turn signal bulb KIA Rio 2005 2.G Owner's Manual

4-35 Turn Signals
The same lever that controls the headlights also con-
trols the turn signals.
The ignition switch must be ON for the turn signals
to function. Move the lever up or down to activate the
turn signals. The turn signals will self-cancel after a
turn is completed. If the indicator continues to flash
after a turn, manually return the lever to the OFF (mid-
dle) position.
Lane Change Signals
To signal a lane change, move the turn signal lever
slightly and hold it in position. The lever will return to
the OFF (middle) position when released.
Green arrow indicators on the instrument panel indi-
cate which turn signal is operating. If an indicator
stays ON and does not flash or if it flashes abnormally,
one or more of the turn signal bulbs may be burned out
and will require replacement.Daytime Running Lights (DRL)Daytime Running Lights (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving condi-
tions, but they can be especially helpful in the short
periods after dawn and before sunset. The DRL system
will make your low-beam headlights turn OFF when:
 The headlight switch is ON.
 The parking brake is engaged.
 The engine stops.
AS2B04023
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 35

7-43 Front Turn Signal / Parking Light Bulb Replacement
1. Turn the parking light bulb socket counterclockwise
and remove it from the headlight assembly.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb in the socket.
4. Re-install the parking light bulb socket into the
headlight assembly and rotate it clockwise to lock
the socket in place.
1B3106006
Rear Combination Light Bulb Replacement1. Using a cross-tip screwdriver, remove the screws
and bolts attaching the rear combination light
assembly to the body.
2. Carefully remove the light assembly from the
vehicle.
1B3106007A
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 43

5. Insert a new bulb in the socket, then push the bulb
in and rotate it one-quarter turn clockwise to lock
the bulb in place.
6. Re-install the bulb socket into the rear combination
light assembly and rotate it one-quarter turn
clockwise to lock the socket in place.
7. Carefully re-install the light assembly in the
vehicle.
Maintenance7-44
AS2B07033
3. Turn the bulb socket counterclockwise and remove
it from the housing.
4. Push the bulb in, then rotate it one-quarter turn
counterclockwise and remove the bulb from the
socket.
1B3106007C
Turn signal bulbStop/tail light bulb
Backup light bulb
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 44

8-3
LIGHT BULBS
Light Bulb Wattage
Front Headlights 60/55
Turn signal lights 28/8
Rear Fog light (if equipped) 27
Stop and tail lights 28/8
Turn signal lights4 Door 27
5 Door 21
Backup lights 27
Side marker lights 5
License plate lights 5
Interior Interior lights 10
High mounted stop 4 Door 21
lights (if equipped) 5 Door 5
Map lights(if equipped) 5
TIRES
SizeInflation Pressure
Front Rear
TypeP175/65R 14 81T 29 psi (200 kPa) 29 psi (200 kPa)
T105/70D 14
60 psi (415 kPa)
T105/70R 14
Spare tire
(Temporary
spare)
RIO ENG CNA 8.qxd 7/29/05 5:19 PM Page 8-3