buttons KIA RIO 2021 Features and Functions Guide

*IF EQUIPPED6RIO FEATURES & FUNCTIONS GUIDE
VEHICLESETTINGS
VEHICLE SETTINGS
OKRES+
SET
-
( Type B shown; located on the right side of the Steering Wheel)
Your vehicle’s steering wheel buttons may differ from those in the illustrations. Refer to section 4 in the Owner’s Manual for more information.
Trip Modes / Trip Computer
The Trip Computer is a driver information system that
displays information related to driving on the display when
the Engine Start /Stop button is in the ON position.
To cycle through the LCD Instrument Cluster modes, press
the Mode button A.
To select and enter the Trip Computer mode , press the
Move button B up/down and then press Set /Reset (OK ) B
to enter. To cycle through and select the different screens
(Fuel Economy, Trip A, Trip B), press the Move button B
up/down again and then press the OK button B. When
displaying the TRIP A or TRIP B screens, press and hold
the OK button B to reset the Tripmeter to zero.
Press the OK button B to go back to the previous mode/item.
REMINDERS:
•
Appearance of Trip Computer / Tripmeter display may differ, as equipped
•
All stored driving information (except Odometer and Range / Distance to Empty) is reset if the battery is disconnected
( Type B cluster)
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
QR CODES
Instrument Cluster’s LCD Display Video
TRIP• Average Fuel Economy• Instant Fuel Economy
ACCUMULATE INFO• Tr ipme t er• Average Fuel Economy• Timer
DRIVE INFO• Tr ipme t er• Average Fuel Economy• Timer
B
A
C
LCD Instrument Cluster Modes
Press the Mode button A to cycle through the different
LCD Instrument Cluster Modes:
Trip Computer Mode: Displays driving information for
tripmeter, fuel economy, drive info, drive mode, etc.
Information Mode*: Displays the speedometer, engine temperature, TPMS and
AWD traction information
User Settings Mode: Change settings of the Driver Assistance, doors, lights, sound
other features
Master Warning Mode: Informs on low tire pressure warnings, Blind-Spot Collision
Warning (BCW )* system malfunction and other systems
Driving Assist Mode: Displays information on Smart
Cruise Control with Stop & Go*, Lane Safety and
Driver Attention Warning*. In AWD AUTO MODE, the
cluster displays the traction force distribution status
of the front and rear wheels. In AWD LOCK MODE,
the cluster doesn’t display the status
Driving while distracted is dangerous and should be avoided. Drivers should remain attentive to driving and always exercise caution when using the steering-wheel-mounted controls while driving.
Refer to section 4 in the Owner’s Manual for more information.

ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED7
VEHICLESETTINGS
VEHICLE SETTINGS
When service is required, the following screens will
be displayed:
•Rotate Tire
•Change Engine Oil
To enter Service Interval Mode, press the Mode button A and scroll to User Settings . Then scroll to Service
Interval using the Move button B.
To reset or deactivate the Maintenance system reminder,
press the Reset button B for more than one second.
Then toggle to the preference and select by pressing the
Reset button B.
Service Interval Setting ( Type B Steering Wheel)
When in User Settings mode, press the Mode
button A to scroll to Service Interval and select by
pressing the OK button C.
When in the Service Interval mode, scroll to the menu
item and press the OK button C to enter:
•Engine Oil
•Tire
Scroll to your selection and press the OK button C to set.
( Type B cluster)
( Type B shown; located on the right side of the Steering Wheel)
For more information on the User Settings mode, please refer to your Owner’s Manual.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
Driving Assist*:
•Warning Timing*
•Driver Attention Warning*
•Forward Safety*
•Lane Safety*
•Blind-Spot Safety*
•Parking Safety*
Lights:
•One Touch Turn Signal
•Headlight Delay
•High Beam Assist (HBA)
Door*:
•Automatically Lock
•Automatically Unlock
•Two Press Unlock*
•Horn Feed Back*
Language:
•To select the language
Convenience:
•Rear Occupant Alert*
•Wiper/Light Display*
•Icy road warning*
Service Interval:
•Enable Service Interval
•Adjust Interval
•Reset
Theme Selection*:
•Select the theme for the
Instrument Cluster
Other Features:
•Fuel Economy Auto Reset
•Speed Unit
•Fuel Economy Unit
•Temperature Unit
•Tire Pressure Unit*
Reset:
•Reset menus in User Settings
User Settings* (Type B cluster)
To enter the User Settings mode in the
LCD Instrument Cluster modes, press the
Mode button A when the vehicle is at a
standstill, gear shift in Park, and with the
ignition ON, select User Settings .
You can navigate the selections on the
display by toggling the Move button B.
Select the item by pressing the OK (Set /
Reset) button C.
User Settings Menu
Service Interval Mode* (Type A cluster)
MPG030
60
INSTFuel
Economy
MPG0 30
60
INSTFuel
Economy
MPG0 30
60
INSTFuel
Economy
BackTire Rotation
OFF9000 km
10000 kmBack OFF7500 mi
15000 mi Engine Oil
Set Tire Service Set Oil Service
Notify Later
Maintenance Reset OFF Notify Later
Maintenance Reset OFF
Rotate Tire
Change Engine Oil
Set Alarm
Set Alarm
RESETRESET
Change Engine Oil
Set Alarm
RESET
Set Oil ServiceNotify Later
Maintenance Reset OFF
Back
OFF7500 mi
15000 mi Engine Oil
MPG0
30
60
INSTFuel
Economy
MPG0 30
60
INSTFuel
Economy
MPG0 30
60
INSTFuel
Economy
BackTire Rotation
OFF9000 km
10000 kmBack OFF7500 mi
15000 mi Engine Oil
Set Tire Service Set Oil Service
Notify Later
Maintenance Reset OFF Notify Later
Maintenance Reset OFF
Rotate Tire
Change Engine Oil
Set Alarm
Set Alarm
RESETRESET
Change Engine Oil
Set Alarm
RESET
Set Oil ServiceNotify Later
Maintenance Reset OFF
Back
OFF7500 mi
15000 mi Engine Oil
MPG0
30
60
INSTFuel
Economy
MPG0 30
60
INSTFuel
Economy
MPG0 30
60
INSTFuel
Economy
BackTire Rotation
OFF9000 km
10000 kmBack OFF7500 mi
15000 mi Engine Oil
Set Tire Service Set Oil Service
Notify Later
Maintenance Reset OFF Notify Later
Maintenance Reset OFF
Rotate Tire
Change Engine Oil
Set Alarm
Set Alarm
RESETRESET
Change Engine Oil
Set Alarm
RESET
Set Oil ServiceNotify Later
Maintenance Reset OFF
BackOFF
7500 mi
15000 mi
Engine Oil
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
QR CODES
Ambient, Mood & Theme Lighting Video
LCD Display: Maintenance Video
OKRES+
SET-B
A
C

ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER9
Lane Keeping Assist and Lane Departure Warning are not substitutes for safe driving and may not always alert the driver if the vehicle is driven outside of its lane. Always drive safely and use caution.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
Actual User Settings steps may vary by model. Refer to section 4 in the Owner’s Manual for more information.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
QR CODES
Lane Keeping Assist (LKA) VideoLK A User Settings:
• To turn LK A ON, with the ignition on or the Engine Start /Stop button* in the ON
position, press the Lane Safety/LK A button* A. The instrument cluster indicator
will initially illuminate white indicating the system is on
• To turn LK A on in the user settings, go to the User Settings menu in the
Instrument Cluster, press the Mode button B on the Steering Wheel when
the vehicle is at a standstill, gear shift in Park and with the ignition on or the
Engine Start /Stop button* in the ON position, and select User Settings
• To switch between LK A modes (Lane Keep Assist, Lane Departure Warning),
go to User Settings in the Instrument Cluster. Press the Move (OK ) button C
up/down and select desired setting and press the OK button C
REMINDERS:
•
LK A will not issue a warning if the turn signals or hazard lights are activated
•
When the ignition is cycled, LK A will return to the previously set state
•
Some models access settings through the Vehicle Settings in the audio head unit. Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings

The LK A Warning Volume can be adjusted in the User Settings in the Instrument Cluster or the Vehicle Settings* on the audio head unit
QUICK TIP
Lane Keeping Assist (LKA)*†6 (continued)
HOLDA
(Located on Panel to the left of the steering wheel)
Lane Keeping Assist and Lane Departure Warning are not substitutes for safe driving and may not always alert the driver if the vehicle is driven outside of its lane. Always drive safely and use caution.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
Actual User Settings steps may vary by model. Refer to section 4 in the Owner’s Manual for more information.
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
( Type B shown; located on the right side of the Steering Wheel)
OKRES+
SET
-
B
C

ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER11
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
QR CODES
Forward Collision-Avoidance Assist (FCA)Video
COLLISION WARNING
EMERGENCY BRAKING
FCA is designed to detect and monitor a vehicle ahead or detect a pedestrian in the roadway through front
view camera recognition and front radar signals to warn the driver that a collision is imminent,
and if necessary, temporarily apply emergency braking. Initially, FCA provides Forward Collision Warning
(FCW ) when it detects a potential collision with a vehicle, pedestrian, or cyclist, emitting an audible
warning and visual alert on the instrument cluster A.
If the system detects that the collision risk has increased, Forward Collision-Avoidance Assist (FCA)
automatically applies the brakes to reduce your speed, potentially
helping to reduce the effects of a possible collision.
FCA User Settings:
• FCA is ON by default in most Kia models. FCA can be turned
ON/ OFF by going to the User Settings in the Instrument Cluster
• To go to User Settings , press the Mode button B on the Steering Wheel when the vehicle is at a
standstill, gear shift in Park and with the ignition on or the Engine Start /Stop button* in the ON position
• Press the OK button C up/down and select User Settings then Driver Assistance
– In some models, go to Driving Assist, then Forward Collision-Avoidance Assist or Forward Collision
Warning and press the OK button C
– In other models, go to Forward Safety and select Active Assist, Warning Only or Off
• Active Assist: Vehicle will provide a warning (audible & visual) and apply the brakes if needed
• Warning Only: Vehicle will provide a warning only (audible & visual)
• Off: System is off, no warnings or braking provided
• To adjust the FCA initial warning activation time, go to User Settings , Driver Assistance, Warning
Timing then select Normal, Early or Late, depending on your Kia model:
–
Early/Normal: Maximizes the amount of distance between the vehicles before the initial warning occurs
– Late: Reduces the amount of distance between the vehicles before the initial warning occurs
FCA/FCW will become active when the:
• Ignition is on or the Engine Start /Stop button* is ON
• Vehicle is traveling faster than 5 mph
• Electronic Stability Control (ESC) is ON

FCA Warning Volume can be adjusted in the User Settings in the Instrument Cluster or the Vehicle Settings* on the audio head unit. Go to Driver Assistance, then Warning Volume
QUICK TIP
A
Forward Collision-Avoidance Assist (FCA)†6
Forward Collision-Avoidance Assist (FCA) is not a substitute for safe driving and may not detect all objects in front of the vehicle. Always drive safely and use caution.
Actual User Settings steps may vary by model. Refer to section 4 in the Owner’s Manual for more information.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
REMINDERS:
• FCA will be activated by default when the ignition is cycled ON, even when previous setting was OFF
• If FCA is operating and the ESC (Electronic Stability Control) is turned off, FCA system is automatically turned off
• When the FCA system is off, the FCA warning indicator is on in the Instrument Cluster
( Type B shown; located on the right side of the Steering Wheel)
OKRES+
SET-B
A
C

ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER13
DRIVER'S PANEL
DRIVER’SPANEL
Instrument Cluster Control
Press switch A up or down to adjust display brightness of the
instrument panel illumination.
REMINDER: The Instrument Cluster Control does not adjust brightness on the audio control unit screen. Use setup to adjust brightness on the audio control unit screen.
Electronic Stability Control (ESC)†8
The ESC system is designed to help stabilize the vehicle during certain
cornering maneuvers. It is a good idea to keep the ESC turned ON for
daily driving whenever possible.
Press the ESC OFF button B to disable Traction Control in ESC (ESC
OFF indicator will illuminate).
To turn both the Tr action Control and Stability Control off, press and
hold the ESC OFF button B (ESC OFF indicator will illuminate, and an
alert sounds).
REMINDERS:
•
ESC is active by default at vehicle startup. When ignition is cycled, ESC will turn ON again
•
The ESC Indicator Light in the instrument cluster will be lit momentarily whenever the ESC is active
For more information on Electronic Stability Control (ESC) and its specific features and operation, please refer to your Owner’s Manual.For illustrative purposes only. Your actual display, buttons and/or features may vary.
Hill-Start Assist Control (HAC)†8
HAC can help to prevent the vehicle from rolling backwards when
accelerating from a stop while on a steep incline.
The HAC automatically activates whether the ESC is OFF or ON but
does NOT activate when the ESC has malfunctioned.
REMINDERS:
•
The HAC does not operate when the gear shift is in the P (Park) or the N (Neutral) position
•HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
•In the event of HAC system malfunction, see an authorized Kia dealer for service
• When HAC is active (e.g., during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator – this is normal HAC operation
• HAC provides a 2-second delay before the vehicle may start rolling backwards
QUICK TIPS(Buttons located on left side of Driver’s Panel)
BA

*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER14RIO FEATURES & FUNCTIONS GUIDE
DRIVER'S PANEL
DRIVER’SPANEL
Power Windows, Window Lock
& Central Door Lock
A Pull/Press to operate Driver’s Window Auto Up/Down*
B Press to Unlock /Lock All Doors
C Press the Power Window Lock button* to disable the
Rear Passenger Window switches
Automatic Door
Lock/Unlock*
Auto Door Lock /Unlock will engage
when the gear shift is moved into
or out of the P (Park) position. Refer
to the User Settings in the LCD
Instrument Cluster modes on how to
turn Auto Door Lock/Unlock ON/OFF.
Power/Heated
Outside Mirrors
To adjust outside mirror positions,
press the switch D left or right to
select mirror, then press the arrows E to adjust.
Mirror heaters are activated when
Rear Defroster is turned on.
Press button again to stop Auto Up/Down function.
QUICK TIP
LR
M I R R O R
For illustrative purposes only. Your actual display, buttons and/or features may vary.
A
B
C
D
E
Engine Start/Stop Button*†1 0
To start the engine:
1. Depress the brake pedal
2.
Press the Engine Start /Stop button while
gear shift is in P (Park) or N (Neutral)
To turn the engine OFF: Press
the Engine Start /Stop button.
To use the Engine Start /
Stop button, you must have
the Smart Key fob inside the
vehicle.
To use electrical accessories:
ACC position •When in the OFF position and without depressing the brake pedal, press the Engine Start/Stop button once (amber light)
ON position •When already in the ACC position (amber light) and without depressing the brake pedal, press the Engine Start /Stop button (red light) •
When in the OFF position and without depressing the brake pedal, press the Engine Start /Stop button twice (red light)
Keeping the vehicle in the ACC or ON position for extended periods of time without turning the engine on may discharge the vehicle’s battery.
QUICK TIPS
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
QR CODES
Engine Start/Stop Button Video
See section 5 in the Owner’s Manual for more information.

ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED15
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
Headlight position
Parking light position
AUTOAuto Light*/HBA position
OFFOFF position
One-Touch Lane Change Signal
(Type A shown)
(Type A shown)
Headlights & High Beams
To o p e r a t e :
•Rotate lever to change the
Headlight function
•Push lever to turn High
Beams ON
•Pull lever to flash Headlights/
High Beams
Turn Signals
To o p e r a t e :
•Turn Signals – Move lever Up/Down for Right /Left
Turn Signal
•One-Touch Lane Change Signal is activated by
briefly pressing the Turn Signal Lever Up/Down
slightly for less than 1 second and then releasing.
The lane change signal will blink 3 times.
•To turn the One-Touch Lane Change Signal off/on, go
to User Settings Mode in the LCD Instrument Cluster
modes.
•To change how many times the Lane Change Signal
blinks (3/5/7), go to User Settings Mode in the LCD
Instrument Cluster modes.
AUTO Light Position — When the light switch is in the AUTO Light position, the tail lights
and headlights will turn ON/OFF automatically depending on the amount of light outside
the vehicle.
High Beam Assist (HBA)* – High Beam Assist is designed to automatically adjust the
headlight range by switching between high and low beams based on light detected from
other vehicles and road conditions.
To enable HBA, toggle the light switch to the AUTO Light position and turn on the high
beams by pushing the lever away from you. The High Beam Assist indicator will illuminate.
Refer to section 4 in the Owner’s Manual for more information.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
REMINDERS:
•
High Beam Assist does not operate below certain speeds, or in some lighting and driving conditions. Please be aware of your surroundings and exercise proper road etiquette when operating a vehicle using the high beams
•HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously. If the lever is pulled toward you while HBA is operational, HBA will turn off
•
If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
•
When the HBA indicator illuminates on the instrument cluster, the HBA is not working properly. See an authorized Kia dealer for service
See section 4 in the Owner’s Manual for more information.

*IF EQUIPPED16RIO FEATURES & FUNCTIONS GUIDE
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
M I S T: Single wipe
OFF: Wiper off
I N T: Intermittent wipe
LO: Low wiper speed
HI: High wiper speed
HI: High wiper speedLO: Low wiper speedOFF: Wiper off
PUSH
REAR
PULL
PUSH
PULL
Q UIC K T IP
PUSH
REAR
PULL
PUSH
PULL
Q UIC K T IP
Windshield Wipers & Washers
To o p e r a t e :
•Move lever up/down to change Wiper modes
•Press switch A up/down to adjust Intermittent Wipe Speed
•Pull lever to spray and wipe
Rear Wiper & Washer
(5-Door only)*
To o p e r a t e :
•Rotate Rear Wiper switch to change
wiper modes
•Push lever to spray and wipe
• Moving switch up increases intermittent wipe frequency and wipe speed. Moving switch down decreases frequency of wipes
• Set the wiper to OFF position when the wiper is not in use
QUICK TIPS
LO and HI sets wiper speed. No intermittent wipe function is available on rear wipers
QUICK TIP
(5-door model stalk shown)
(5-door model stalk shown)
For illustrative purposes only. Your actual display, buttons and/or features may vary.
Refer to section 4 in the Owner’s Manual for more information.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
Refer to section 4 in the Owner’s Manual for more information.
A
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
QR CODES
Wipers and Wiper Stalk Video

ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER17
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
Tilt Steering Wheel†21
To adjust the Steering Wheel position, press the lock-release lever A
down and adjust the desired angle B. When finished, pull the lock-release
lever A up to lock Steering Wheel in place.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
A
B
C CRUISE Control button: Press to turn the Cruise Control
ON/OFF
D Resume (RES) Cruising Speed button: Press up to resume or
increase cruising speed SET Cruising Speed button: Press down to set or decrease
Cruising Speed
E Cruise Control CANCEL button: To cancel Cruise Control, do one of
the following:
•Press the brake pedal
•Press the CANCEL button
( Type B)
OK
RES+
SET
-
CRUISE
CANCEL
Cruise Control*†19
• Cruise Control is designed to function above approximately 20 mph
• The cruise control system will not activate until the brake pedal has been depressed at least once after ignition ON or engine starting
QUICK TIPS
E
D
C

*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER18RIO FEATURES & FUNCTIONS GUIDE
AUDIO SYSTEMS
AUDIOSYSTEMS
A Talk button: Press to activate voice recognition.
Press and hold to exit voice recognition.
B Volume button: Press up/down to raise/lower
speaker volume
Mute button: Press to mute the microphone during a
call and to mute the audio system speakers
C Receive/Place Call button: Press to receive/place/
transfer calls. In vehicles with navigation, if no phone
is paired, press button to pair a phone
D End Call button: Press to end a call, reject an
incoming call or cancel a function
OKR ES+
SET
-
( Type B)
Bluetooth® Wireless Technology† 5 ,19
REMINDER: Your vehicle’s steering wheel buttons may differ from those in the illustrations. See your Owner’s Manual for more details.
Driving while distracted is dangerous and should be avoided. Drivers should remain attentive to driving and always exercise caution when using the steering-wheel-mounted controls while driving.
For more information, refer to the Car Multimedia System User's Manual. For Bluetooth® Wireless Technology FAQs, go to www.kia.com, Owners section, or call Consumer Information for Bluetooth® Technology at (800) 333-4KIA. Refer to your Owner’s Manual for more specific Bluetooth® Wireless Technology phone pairing and operation instructions.
Pairing a Phone
For instructions on how to pair a phone, refer to the audio
system’s user’s guide or your vehicle’s Quick Start Guide.
• When using the voice command feature, wait for the system BEEP before speaking the command.
• Phone book transfer upload time varies by phone model and with number of phone book entries
• Because of differences in phone quality, service providers and Bluetooth® Wireless Technology chip programming, functionality may differ from one phone to another
QUICK TIPS
During the pairing process, be sure to accept the connection requests on the phone for phone book download and to allow acceptance of all future Bluetooth® connection requests.
QUICK TIPS
How to Place a Call
When using the voice command feature, wait for the system
BEEP before speaking the command.
There are two options for placing a call:
•Option 1: Press the Receive/Place Call button C (displays the
phone screen with number keypad)
•Option 2: Press the Talk button B. Then say the command
“Call {name}” or “Dial {number}” 
B
A
CD