instrument cluster KIA STINGER 2022 Features and Functions Guide

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Lane Keeping Assist (LKA)†6
Lane Keeping Assist is designed to detect the lane markers on the road with a front view camera on the windshield, and may assist the driver ’s steering to help keep the vehicle in the lane . When turned on, the instrument cluster
indicator will initially illuminate white . It will remain white when the vehicle is traveling slower than 40 mph or when the system does not detect the lane markers . When the system detects the lane markers and can assist the steering, the LK A icon will illuminate green .
If LK A detects that you are moving outside of your lane, the system may give an audible warning and display Lane Departure Warning on the instrument cluster . If the vehicle continues to move outside of the lane, LK A may provide steering, trying to prevent the vehicle from moving outside its lane .
LK A is the operating mode by default when the Lane Safety button* A is depressed to ON . To activate/deactivate LK A , press A .
There are three available modes:
•Assist: LK A will automatically assist the driver ’s steering when lane departure is detected to help prevent the vehicle from moving out of its lane
•Warning Only: LK A will warn the driver with an audible warning when lane departure is detected . The driver must steer the vehicle
•Off: LK A will turn off . The B indicator light will turn off on the cluster
•All systems will operate under the following conditions:
–The vehicle speed exceeds approximately 40 mph
–
LK A recognizes both sides of the lane markers the vehicle is traveling in
–
The vehicle is between the lane markers
Lane Keeping AssistLane Keeping AssistLane Keeping Assist
Lane Keeping Assist is not a substitute for safe driving and may not always warn the driver if the vehicle is driven outside of its lane . Always drive safely and use caution .
For illustrative purposes only . Your actual display, buttons and/or features may vary . Actual User Settings steps may vary by model .
Refer to section 5 in the Owner’s Manual for more information .
When the front-view camera does not detect the lane traveling in, the lanes are not illuminated gray
When the front-view camera detects the lane traveling in, both lanes are illuminated gray
Lane Keeping Assist
When the front-view camera detects the vehicle moving outside of the lane it is traveling in, a vehicle crossing lane indicator will blink, either on the left or right lane (as shown in both images above)
(But ton located on driver ’s panel, left of the steering wheel)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Lane Keeping Assist (LKA) Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED13
REMINDERS:
•
LK A will not issue a warning if the turn signal or hazard signal is activated
•
LK A will return to its previous state when the ignition is cycled
•
LK A is not a substitute for safe and proper driving . Always drive safely and use caution
•
LK A may not always aler t the driver if the vehicle is about to be driven outside of its lane
A
B

ADAS
Blind-Spot Collision-Avoidance Assist (BCA)†6
BCA uses rear corner radar sensors in the rear bumper to monitor and warn the driver in certain situations if it detects an approaching vehicle in the driver ’s blind spot area and before changing lanes . Initially, BCA provides
Blind-Spot Collision Warning (BCW) when it detects a potential collision with a vehicle, emitting an audible warning and visual alert on the outside rearview mirrors . If the system detects that the collision risk has increased, Blind-Spot Collision-Avoidance Assist (BCA) automatically applies the opposite side front brake to try and mitigate a potential collision .
•
1st-stage: When another vehicle is detected within BCW warning boundary A, an indicator will illuminate on the outside rearview mirrors B .
•
2nd-stage: When 1st stage warning is on and the driver activates a turn
signal, a flashing indicator will illuminate on the outside rearview mirrors and the system will sound a warning .
• 3 r d - s t a g e : When 1st stage warning is on and the 2nd stage warning has already occurred, and the collision risk has increased, braking is applied to the opposite side front wheel and a visual warning occurs .
BCA User Settings:
To turn BCA on, go to the User Settings menu in the Instrument Cluster, press the Mode button C on the Steering Wheel when the vehicle is at a standstill, gear shift in Park and with the ignition switch or the Engine Start/Stop button* in the ON position, and select User Settings . Press the Move (OK) button D up/down and select Driver Assistance, Blind-Spot Safety and then press the OK button D .

Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then Vehicle on the screen to enter Vehicle Settings

To set BCA when in Blind-Spot Safety, select:
•Active Assist: BCA will provide a warning (audible & visual) and may activate Electronic Stability Control (ESC) and temporarily apply braking power
•Warning Only: Vehicle will provide a warning only (audible & visual)
•Off: System is off, no warnings provided

To set the initial warning activation time, go to User Settings , then Driver Assistance, Warning Time and press the OK button D . Adjust the warning timing:
•
Early/Normal: Maximizes the amount of distance between the vehicles before the initial warning occurs
• L a t e : Reduces the amount of distance between the vehicles before the initial warning occurs
(Blind-spot area monitoring)
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
RESOKSET
(But ton layout on right of steering wheel)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Blind-Spot Collision-Avoidance Assist (BCA) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED14STINGER FEATURES & FUNCTIONS GUIDE
A
B
C
D

ADAS
Blind-Spot Collision-Avoidance Assist (BCA)† 6 (continued)
REMINDERS:
•
BCW will not issue a warning if the vehicle speed is 6 mph or more above the surrounding vehicles
•
When BCW is ON and the ignition is cycled, BCW returns to its previous state
•
BCW is a supplemental system . Do not solely rely on this system . Always pay at tention to the road and drive safely
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
The BCA system is not a substitute for safe and proper driving . Always drive safely and use caution .
Refer to section 5 in the Owner’s Manual for more information .
The images on this page are for illustrative purposes only and may not reflect actual feature or operation .
Safe Exit Assist (SEA)†6
Safe Exit Assist can help prevent passengers from opening their door by displaying a warning message on the Instrument Cluster and sounding an audible warning when a vehicle is detected, approaching from behind, after your vehicle has stopped .
SEA warns the driver of the risk of collision with a vehicle approaching the blind spot area .
To turn on SEA , go to User Settings in the Instrument cluster or press SETUP in the Vehicle Settings* in the audio head unit, then select Driver Assistance, Blind-Spot Safety, and select Safe Exit Assist .
Images are for illustrative purposes only and may not reflect actual feature or operation .
See section 4 in the Owner’s Manual for more information .
Watch for traffic
3FGFS
UP
UIF
JOTJEF
GSPOU
DPWFS
GPS

NPSF
JOGPSNBUJPO
PO
23
DPEFTXXXZPVUVCF DPN,JB'FBUVSF7JEFPT
Safe Exit Assist (SEA) Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED15
•
BCW Warning Volume can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings* on the audio head unit . Go to Driver Assistance, then Warning Volume
•
BCW will activate when:
-The system is turned on
-Other vehicles are detected on the rear sides of the vehicle
-Vehicle speed is above approximately 20 mph
QUICK TIPS

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Driver Attention Warning (DAW)†7
Driver Attention Warning is designed to alert the driver if it detects inattentive driving practices and, in certain situations, can give a warning signal to take a break from driving .
•Inattentive Driving Warning: DAW will inform the driver of the driver ’s attention level and will recommend taking a break when it falls below a certain level
•Leading Vehicle Departure Alert: DAW will inform the driver when the front vehicle departs from a stop
If DAW is activated, the DAW information A will appear on the Instrument Cluster LCD when you select the Driving Assist menu in User Settings . A message, “Consider taking a break,” B appears on the LCD and a warning sounds to suggest the driver take a break when the driver ’s attention level
becomes low C .
DAW User Settings:
To turn DAW on/off, with the ignition on, press the Mode button D on the Steering Wheel and go to User Settings in the Instrument Cluster . Then go to Driver Assistance and select Driver Attention Warning .
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then press Vehicle on the screen to enter Vehicle Settings
REMINDERS:
•
The set-up of DAW will be maintained, as selected, when the ignition is cycled
•
When activated, DAW does not display the “Consider taking a break ” message when the total trip driving time is less than 10 minutes
•DAW will enter a standby mode if the camera does not detect the lanes
Refer to section 5 in the Owner’s Manual for more information .
Consider taking a break
Attention Level
High
Driver Attention Warning is not a substitute for safe driving and may not detect all instances of inattentive driving practices . Failure to pay attention to travel conditions and vehicle operation could result in loss of vehicle control . Always drive safely and use caution .
RESOKSET
(But ton layout on right of steering wheel)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Driver Attention Warning (DAW) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED16STINGER FEATURES & FUNCTIONS GUIDE
AB
C
D

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Smart Cruise Control is designed to maintain a predetermined distance from vehicles detected ahead by automatically adjusting the driving speed as needed . When traffic is detected, the vehicle will slow down to maintain a
set distance behind traffic without depressing the accelerator or brake pedal .
With SCC on and activated, the vehicle distance set, and the system detects a vehicle slowing or stopping, the system can bring the vehicle to a complete stop . When the vehicle ahead starts to move forward, SCC re-engages . If the vehicle ahead stops for more than 3 seconds, the accelerator pedal or the RES+ button must be pressed to start moving the vehicle .
Smart Cruise Control will adjust acceleration based on the drive mode selected in the Drive Mode Integrated Control system .
Press the Driving Assist button* on the Steering Wheel A to activate and the speed will be set to the current vehicle speed . SCC may decrease the speed to maintain the distance with the vehicle in front .
To set/adjust the SCC speed:
•Press the Driving Assist button A to turn the system ON . The CRUISE indicator will illuminate on the instrument cluster
•Accelerate/decelerate to the desired speed
•Press the R E S + / S E T– button B to set the speed . Press the R E S + / S E T– button B up/down to increase/decrease the set speed
To set the vehicle distance:
•Press the Vehicle Distance button C on the steering wheel
•
Each time you press C the vehicle distance will change D, indicated by the number of bars that appear on the display E
To pause/resume SCC operation: Depress the brake pedal or press the Pause/Resume button* B . The
cruise indicator on the instrument cluster will change .
To turn SCC OFF: Press the Driving Assist button A . The CRUISE indicator on the instrument cluster will turn OFF .
To adjust the sensitivity of SCC: Press the mode button F on the Steering Wheel . With the OK button H, select Drive Assistance, then SCC Response . Then select Fast, Normal or Slow .
Images are for illustrative purposes only and may not reflect actual feature or operation .
See section 5 in the Owner’s Manual for more information .
CRUISE
CANCEL
RESOKSET
RESOKSETCRUISE60MPH
(Distances are approximate and var y depending on vehicle speed)
(Display on LCD screen)
172ft130ft
82ft
106ft
Smart Cruise Control (SCC)†6
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Smart Cruise Control with Stop & Go Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED18STINGER FEATURES & FUNCTIONS GUIDE
AD
E
F
HB
CF

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Lane Following Assist is designed to help ensure that the vehicle stays centered in its lane A by monitoring the detected lane markings ahead and adjust the steering . When driving, LFA can be switched on and off
by pressing the Driving Assist button B . When turned on, the instrument cluster indicator will initially illuminate white when turned ON . It will remain white when the system does not detect the lane markers . When LFA detects the lane markers and can assist the steering, the LFA icon will illuminate green C .
LFA will operate only when these conditions are met:
•LFA recognizes both sides of the lane markers the vehicle is traveling in
•The vehicle is traveling slower than 120 mph
LFA User Settings:
•
To go to User Settings in the Instrument Cluster, press the Mode button D on the Steering Wheel when the vehicle is at a standstill, gear shift is in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To enable LFA , when in User Settings, press the Move (OK) button E up/down and Select Driver Assistance then Driving Assist, and select Lane Following Assist . Press the OK button E
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings
•
Some vehicles have a Lane Driving Assist / Lane Safety button* on the Driver ’s Panel or the Steering Wheel B . Press to activate Lane Following Assist
Lane Following Assist (LFA)†6
RESOKSET
RESOKSET
Images are for illustrative purposes only and may not reflect actual feature or operation .
LFA is supplemental . Do not solely rely on this system and always pay attention to the road and its conditions .
See section 5 in the Owner’s Manual for more detailed information, limitations and conditions .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Lane Following Assist (LFA) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED20STINGER FEATURES & FUNCTIONS GUIDE
A
C
D
E
B
REMINDER: LFA is not a substitute for safe and proper driving . Always drive safely and use caution .

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
116mi
R5643mi80°F
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) is designed to warn the driver under certain conditions . It may activate the Electronic Stability Control (ESC) and temporarily apply braking if it detects cross traffic
approaching the vehicle when the vehicle is in reverse .
When the RCCA rear-corner radar sensors detect approaching vehicles from the rear left or rear right side of the vehicle A, RCCA will sound a warning, the warning indicators on the outside rearview mirror will illuminate and a message will appear on the Instrument Cluster LCD B and the audio head unit .* If RCCA detects that the collision risk has increased, RCCA automatically applies the brakes to reduce your speed, potentially helping to minimize the effects of a possible collision .
RCCA is designed to operate under the following conditions:
•When the gear shift is in Reverse
•When the vehicle is moving slower than 6 mph
RCCA User Settings:
•To go to the User Settings menu in the Instrument Cluster, press the Mode button C on the Steering Wheel when the vehicle is at a standstill, gear shift in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To turn RCCA on when in User Settings , press the Move (OK) button D up/down, select Driver Assistance, Parking Safety, Rear Cross-Traffic Safety and then press OK D
•
To set the warning timing, go to User Settings , press the Move (OK) button D up/down, then go to Driver Assistance, Warning Timing and press the OK button D
•Select one of the settings:
–
Early/Normal/Standard: Maximizes the amount of distance between the vehicles before the initial warning occurs
– L a t e : Reduces the amount of distance between the vehicles before the initial warning occurs
•The default Warning Timing is set to Normal . If the Warning Timing is changed, the warning time of other Driver Assistance systems may also change
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings
Rear Cross-Traffic Collision-Avoidance Assist (RCCA)†6
RESOKSET
See section 5 in the Owner’s Manual for more information .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED22STINGER FEATURES & FUNCTIONS GUIDE
A
B
C
D
REMINDERS:
•
The RCCA feature can be activated or deactivated in User Set tings, under Driver Assistance, Parking Safet y
•
When vehicle power is cycled, RCCA will remain in the previous state
•
When a vehicle is approaching within the sensing range, and traveling faster than 3 mph, the RCCA system will show a warning
•
RCCA is a supplemental system . Do not solely rely on this system and always pay at tention to the road and its conditions
•RCCA Warning Volume can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings on the audio head unit . Go to Driver Assistance, then Warning Volume
QUICK TIP

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Head-Up Display is a supplemental system . Do not solely rely on the system, always drive safely, and pay attention to the driving conditions on the road .
Images are for illustrative purposes only and may not reflect actual feature or operation . See section 4 in the Owner’s Manual for more information .
Head-Up Display (HUD)*† 13
The Head-Up Display (HUD) is a semi-transparent display that projects a snippet of information from the instrument cluster and navigation system* onto the windshield glass .
To turn HUD ON or OFF, go to User Settings in the LCD Modes .
The HUD displays:
•Turn By Turn (TBT) navigation information
•Road signs
•
Speedometer
•
SCC vehicle distance information
•
Lane Departure Warning information
•
Blind-Spot Safety information
•Warning lights (low fuel)
•
AC mode information
•Lane Following Assist information
•Highway Driving Assist information (if equipped)
•Navigation-based Smart Cruise Control information*
Head-Up Display (HUD) User Settings
Drivers can adjust the HUD settings from the LCD Instrument Cluster modes in User Settings . HUD settings include:
•Enable Head-Up Display
•Display Height: Adjust the height of the HUD image on the windshield glass
•
Rotation: Adjust the degree of HUD rotation
•
Brightness: Adjust the intensity of the HUD brightness
•
Contents Select: Activate or deactivate HUD content (TBT*, SCC, LK A , BCW)
•
Speedometer Size: Choose the size of the HUD speedometer (Small, Medium, Large)
•Speedometer Color*: Choose the color of the HUD speedometer (White, Amber, Green*)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Head-Up Display (HUD) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED24STINGER FEATURES & FUNCTIONS GUIDE
REMINDERS:
•
The HUD image on the windshield glass may not be visible when:
–
The driver has poor sit ting posture
–The driver is wearing polarized sunglasses
–There is an object covering the HUD
–Driving on a wet road
–Excessive lighting inside or outside the vehicle
•
Modifications made to the windshield, such as tinting or other aftermarket treatments, could affect the HUD . When replacing the front windshield glass of vehicles equipped with the HUD, owners must replace it with windshield glass designed for HUD operation . Other wise, duplicated images may be displayed on the windshield glass
•
If Turn By Turn (TBT) navigation information is selected as HUD content, TBT information will not be displayed on the LCD

DRIVER’S PANEL
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFF
OFF
VIEW
P
For more information on Electronic Stability Control (ESC) and its specific features and operations, please refer to section 5 in the Owner’s Manual .
Electronic Stability Control (ESC)†8 / Traction Control System (TCS)†8
Electronic Stability Control (ESC) is designed to help stabilize the vehicle during certain cornering maneuvers
. Traction Control System (TCS) can help improve traction . It is a good idea to keep both ESC and TCS turned
on for daily driving whenever possible .
Press the ESC button A to turn Traction Control System OFF/ON .
To turn both Electronic Stability Control and Traction Control System OFF, press and hold the ESC button for more than 3 seconds . Press again to turn ON .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electronic Stability Control Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED25
DRIVER’S PANEL
REMINDERS:
•
ESC is active by default at vehicle star t-up . When ignition is cycled, ESC will turn ON again
•
The ESC indicator light in the instrument cluster will be lit momentarily whenever ESC is activeA
Refer to section 4 in the Owner’s Manual for more information .
Instrument Cluster Control (Instrument Panel Dimmer)
With parking lights/headlights ON, press B (+) or (-) to adjust the brightness of the Instrument panel illumination .B
Refer to section 5 in the Owner’s Manual for more information .
Hill-start Assist Control (HAC)†8
Hill-start Assist Control (HAC) is designed to prevent the vehicle from rolling backwards when accelerating from a stop while on a steep incline .
HAC automatically activates whether ESC is OFF or ON but does NOT activate when ESC has malfunctioned .
REMINDERS:
•
HAC does not operate when the gear shift is in P (Park) or N (Neutral) position
•
HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
•
In the event of HAC system malfunction, see an Authorized Kia Dealer for ser vice
•When HAC is active (e .g ., during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator . HAC does not replace the need to apply brakes while stopped on an incline
•
HAC provides a t wo-second delay before the vehicle may star t rolling backwards
QUICK TIPS

DRIVER’S PANEL
A Pull/Press to operate driver and front passenger ’s window auto up/down
B Press to unlock/lock all doors
C Press to disable the rear passenger window controls
Power Windows, Window Lock & Central Door Lock
Power Folding Outside Mirrors
D Press the L or R buttons to select the mirror to adjust
E Press button arrows left/right or up/down to adjust mirror position
F Toggle button left/right to unfold/fold the outside rearview mirrors
F Toggle button to center to automatically fold/unfold mirrors when:
•Smart Key lock/unlock buttons are pressed
•Outside door handle button is pressed
•Driver approaches the vehicle with the Smart Key (if activated in User Settings)
See section 4 in the Owner’s Manual for more information .
*IF EQUIPPED26STINGER FEATURES & FUNCTIONS GUIDE
DRIVER’S PANELREMINDER: When pressed C, the rear window controls for the Rear Passenger Windows are disabled .
Button configuration may vary depending on vehicle model .
See section 4 in the Owner’s Manual for more information .
REMINDERS:
•
When the mirror toggle but ton is in the center, press the lock but ton t wice on the Smar t Key to automatically fold mirrors when exiting vehicle
•
To lock the mirror position, toggle but ton to the neutral (center) position
•
Press but ton A again to stop Auto Up/Down function
•
Auto Door Lock/Unlock* will engage when gear shift is moved in to or out of the P (Park) position
•
To turn Auto Door Lock/Unlock* OFF, go to User Set tings* in the LCD Instrument Cluster Modes
•
While driving with the rear windows down or with the sunroof* in an open or par tially open position, a wind buffeting or pulsation noise may be heard . This noise is a normal occurrence and can be reduced or eliminated by the following:
–
If the noise occurs with one or both of the rear windows down, par tially lower both front windows approximately 1 inch
–
If the noise occurs with the sunroof open, slightly reduce the size of the sunroof opening
QUICK TIPS
•
The mirrors will automatically unfold when the Smar t Key is within close proximit y to the vehicle (if activated in User Set tings)
QUICK TIP
A
B
C
D
D
EF