ignition KIA STINGER 2023 Features and Functions Guide

STEERING WHEEL
CONTROLS
STEERING WHEEL CONTROLS
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED33
To operate:
•Move lever up/down to change wiper modes
–MIST: Single wipe
–OFF: Wiper off
–AUTO: Auto Rain Sensing
–LO: Slow wipe
–HI: Fast wipe
•
Pull to spray and wipe
Auto Rain Sensing
The rain sensor located on the upper end of the windshield glass is designed to sense the amount of rainfall and control the wiping cycle for the proper interval . The more it rains, the faster the wiper operates . When the rain stops, the wiper stops .
To turn ON the auto rain sensing wipers, move lever up/down to AUTO .
To adjust the auto rain sensing wiper speed setting, move the speed control switch A up/down .
MIST
OFF
AUTO LOHIAUTO
Windshield Wipers & Washers
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wipers and Wiper Stalk Video
Lifting Wipers / Wiper Service Mode Video
QR CODES
•
When the Engine Star t/Stop but ton is in the ON position and the wiper switch is in AUTO mode, the wiper will automatically operate once to per form a self-check of the system
•
Set the wiper to the OFF position when the wiper is not in use
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the Smar t Power Liftgate* lid control, turn off the auto rain sensing wipers and fold in the mirrors
•
Moving lever to HI increases Intermit tent wipe frequency and wipe speed . Moving lever to LO decreases frequency of wipes
•
Pressing but ton A up increases Intermit tent wipe frequency and wipe speed . Pressing but ton down decreases frequency of wipes
QUICK TIPS
A
Lifting Wipers (Wiper Service Mode)
To lift the windshield wipers to clean windshield, inspect or replace wiper blades or raise wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the service position B .
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch to the MIST position C and hold the switch for more than two seconds until the wiper blade is in the fully up position .
To return wipers to normal position, turn the ignition ON, then activate MIST .See section 4 in the Owner’s Manual for more information .
B
C

INFOTAINMENT SYSTEM
Kia Access†1 App Download
Go to an app marketplace to download the Kia Access App . Once you download the app, make sure you register your vehicle and start an account (refer to Kia
Connect link Activation page) . Get to know your new Kia and the available convenient features on the app .
Download the Kia Access App by clicking this dynamic QR code . Some phone’s operating systems may need to be updated to scan dynamic QR codes .
Kia Access App Features Guide. Click this dynamic QR code to access the guide . Some phone’s operating systems may need to be updated to scan dynamic QR codes .
2020 SOULMILEAGE722 mi.
355 miEst. RangeDOOR LOCKS REMOTE STARTFind My Car
Kia Access†1 App Features Guide
The Kia Access App Features Guide helps you
utilize the app to its full potential by detailing how to set up and use each feature and adjust various settings . Below are some of the topics included:
•Remote Commands
•Set Climate
•Schedule Service
Do not use remote climate control or remote start if vehicle is in an enclosed area (e .g ., closed garage) or a partially enclosed area without ventilation . Close all doors leading from adjacent living areas to the vehicle area before executing a remote climate control or remote start command .
Kia App Screen for illustrative purposes only . Actual App screen and functionality may vary .
Kia Connect may be unavailable for model year 2022 and later vehicles sold or purchased in Massachusetts . See Kia Connect Terms of Service at owners .kia .com for more information .
For further Kia Connect operations, refer to the Car Infotainment System Quick Reference Guide .
QR CODES
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED41
INFOTAINMENT
SYSTEM
•The smar tphone and vehicle need to be connected to a cellular net work with a good wireless signal strength in order to use Kia Connect . If these conditions are not met, remote command may not execute or may take a long time . It will also affect voice commands such as navigation POI or address search
•To use Remote Star t or Remote Star t with Climate Control feature, all doors, hood and trunk/liftgate must be closed and locked
•When Remote Star t is activated, if the driver does not enter the vehicle within 10 minutes, the Remote Star t will turn the engine off
•When using Remote Star t with Climate Control, turn on for at least a few minutes before get ting into the vehicle, allowing the vehicle interior to reach your desired temperature
•The quickest way to obtain accurate vehicle status through the app is by pressing the refresh but ton on the app or refreshing the web page when using the customer web por tal
•In order to preser ve the vehicle bat ter y, Kia Connect will not turn on seven days after the last ignition was on . You will need to restar t the vehicle with a key fob in order to use Kia Connect again
•To keep your map and soft ware up to date, free of charge, visit the of ficial Kia update webpage at ht tps://update .kia .com/US/EN/Main . Note, visiting a dealer for soft ware update may include an additional charge .
QUICK TIPS

ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED43
See section 4 in the Owner’s Manual for more information .
12V180WUSB
(Located in center console in front of gearshift)
Multimedia USB Ports, Power Outlets & USB Charger Ports
Power Outlets A : Use the power outlets for mobile phones and other devices designed to operate on a 12V (180W max) power outlet .
Multimedia Ports B : Use the USB port to connect audio devices and the USB port to connect USB audio devices and smartphones .
USB Charger Port (on back of center console): Devices can be recharged using a USB cable . The Engine Start/Stop button needs to be in the ACC/ON/START position to operate the USB Charger .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Multimedia USB Port, Power Outlets & USB Charger Port Video
QR CODE
•
The power outlets are inactive when ignition is in the OFF position
•
USB data por t is located next to the Power Outlets B . USB Charger does not suppor t data transfer
QUICK TIPS
REMINDERS:
•
Using the power outlets (accessor y plugs) for prolonged periods of time with the Engine Star t/Stop but ton in the ACC position (Engine OFF) may cause the bat ter y to discharge
•
Only use manufacturer cables that came with your device as third par t y cables may cause damage to the device . It is recommended to always update your phone to the latest operating system release
Digital Clock - Infotainment System
Select SETUP key on the infotainment system . Press General and then scroll to and select DATE/TIME, and adjust .
Refer to the Car Multimedia System User ’s Manual for more information .
REMINDERS:
•
Daylight Saving must be enabled or disabled in the Clock Set tings screen .
•
To access manual date and time set ting, turn GPS Time OFF in the Clock Set tings
BA
CENTER PANEL
CENTER PANEL

CENTER PANEL
CENTER PANEL
Charge a Qi Certified smartphone wirelessly by placing it on the charging pad A at the front of the console, near the Multimedia USB ports and the charging indicator, while the ignition is on .
1 .
Enable Wireless Charging in the User Settings* in the Instrument Cluster LCD or the Vehicle Settings* in the infotainment system, select Convenience then Wireless Charging System
2 .
Slide open tray cover B . Place compatible smartphone on the center of the charging pad A
3 .
Indicator light†2 1 C may change to amber once the wireless charging begins
4 .
Once charging is complete, the orange light C may change to green
(Located in center console in front of gearshift)
12V180WUSB
Wireless Smartphone Charging System*†1 7
See section 4 in the Owner’s Manual for more information .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wireless Charging Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED44STINGER FEATURES & FUNCTIONS GUIDE
•
For wireless charging to occur, all doors (excluding rear hatch) must be closed and the Smar t Key Fob must be detected inside the vehicle
•
For best results, place smar t-phone on the center of the charging pad
•
If wireless charging does not work, move smar tphone around the pad until the charging indicator turns amber .
•
Avoid placing other metal items in the bin while charging as to not impede the charging area
QUICK TIPS
REMINDERS:
•If driver door is opened, charging will be disabled . All doors must be closed
•
The smar tphone must be a compatible QI cer tified phone with QI function available . Some smar tphone models are not QI cer tified, which may affect the availabilit y, speed or per formance of the wireless charging
•
Avoid placing other metal items in the bin while charging as to not impede the charging area
•
Wireless charging technology allows for a device to be charged using inductive charging . See your Owner ’s Manual for more detailed information and the back page for legal disclaimers
•
Inductive charging systems are less ef ficient than conventional charging through cable . As a result, higher device operating temperatures may be experienced during use
•
Charging Per formance – Device position on the wireless charging system can affect charging per formance . Other factors that may affect the charging rate includes foreign objects, such as coins or pens, and phone case thickness
CA
B

CENTER PANEL
CENTER PANEL
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . 45*IF EQUIPPED
Idle, Stop and Go (ISG) System*
The ISG system is designed to reduce fuel consumption by automatically shutting down the engine when the vehicle is at a standstill .
When the ISG system is ON and the vehicle is at a standstill the engine will stop, and the green AUTO STOP indicator A on the instrument cluster will illuminate .
The engine will restart when the brake pedal is released or the shift lever is moved from D (Drive) to the R (Reverse) position or to Manual Shift mode* . When the engine restarts, the green AUTO STOP indicator on the instrument cluster will turn off .
To deactivate the ISG System, press the ISG OFF button B . If you press again, the system will be activated .
For more information on Idle, Stop and Go System, refer to section 5 in the Owner ’s Manual or contact your local dealership .
Images are for illustrative purposes only and may not reflect actual feature or operation .
(Type B instrument cluster shown)
0
1 2
3
4
x1000 rpm5
6
7
8
C HE F
km/h
MPH
2030
40
10 0
10 0
80 130
160
200
230
260
290
60
40
20
10 012 0
1 4 0
1 6 0
1 8 0
50
80
60
1 0
0
EPB
AUTO
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFF
OFF
P
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Idle, Stop and Go Video
Launch Control Video
QR CODES
ABC
D
• The ISG system is disabled when:
–A seat belt is unfastened
–The hood or a door is opened
–Bat ter y condition is poor
–
The front or rear defroster is turned on
–
Engine coolant temperature is low
–
The outside ambient temperature is too low/high
–
Emission control devices activate
–
The vehicle is on a steep slope
QUICK TIPSREMINDERS:
•
ISG is active by default at vehicle star t-up . When ignition is cycled, ISG will turn ON again
•
Under cer tain conditions, the engine will restar t automatically even if the brake pedal is still depressed
•
If the AUTO STOP indicator is continuously blinking yellow and the ISG but ton LED is on, please contact an authorized Kia dealer
Refer to section 5 in the Owner’s Manual for more information .
Launch Control aids in controlling acceleration to help the vehicle accelerate smoothly and quickly, while avoiding slipping of the drive wheels and other engine, clutch and gearbox issues .
To turn on, press and hold the ESC OFF button C for more than three seconds while DRIVE MODE D is in SPORT Mode .
To activate, with the left foot press brake firmly while gear shift is in D (Drive) and then press the accelerator pedal fully to the floor . The LCD will display a ready status .
Launch Control*
REMINDERS:
•
When launching, stop vehicle and keep steering wheel straight
•
Brake pedal, EPB and Auto Hold must be released for smooth launching
•
Always drive safely and use caution

CENTER PANEL
AUTOSYNCOFFCLIMATE
A/C
REAR
FRONT
Face-Level Floor-Level
Bi-Level Floor/ Defrost-Level
Auto Defogging System
Auto defogging is designed to reduce the fogging up of the inside of the windshield by automatically sensing the moisture of the inside of the windshield . The system will automatically change to defrost mode when needed .
Auto Defogging is set ON by default . To cancel Auto Defogging, press the Front Defrost button for three seconds (with the ignition ON; the ADS OFF icon will illuminate) . To turn Auto Defogging on again, press the Front Defrost button for three seconds .
Defrost Outside / Defog Inside Windshield
1 . Set Fan Speed to highest position
2 . Set Temperature to highest position
3 . Press the front defrost button B
See section 4 in the Owner’s Manual for more information .
Automatic Climate Control System
Front Climate Control
A AUTO (Automatic) Climate Control
button / Driver ’s Temperature Control Knob
B Front Windshield Defrost button
C Rear Window Defrost button
D Air Conditioning button
E Recirculated Air button
F Fresh Air button
G System OFF button
H Fan Speed Control buttons
I Mode Select button
J Climate Control display on/off
K SYNC (Synchronize All Zones) Temperature Control button / Passenger’s Temperature Control Knob
Climate Control Auto Function
Press AUTO A to select full auto operation . In AUTO mode the driver and front passenger have full control of their own temperature zones . The mode, fan speed, air intake and air conditioning will activate and adjust accordingly to achieve the temperature settings for each zone .
To set temperatures:
•Tu r n A to set the driver ’s zone temperature
•Tu r n K to set the front passenger ’s zone temperature
Dual-Zone Climate Control
Pressing the SYNC button K synchronizes both climate control zones (driver and passenger) to the driver ’s temperature control .
Air Flow Modes
To select air flow modes, press the Mode Select button I :
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Automatic Climate Control Operation Video
Auto Defogging System (ADS) Video
QR CODES
*IF EQUIPPED46STINGER FEATURES & FUNCTIONS GUIDE
AK
B
G
C
H
D
I
EF
J
REMINDERS:
•
Continuous use of the climate control system in the recirculated air position may allow humidit y to increase inside the vehicle which may fog the glass and obscure visibilit y
•
When in AUTO mode, Air Flow Mode and Fan Speed do not display on the Climate Control Display
•
Warm or cold outside air may flow in through vents if Recirculated Air but ton is not pressed ON (LED lit)
•
Continuous use of the A /C and heater may increase Energy Consumption, especially excessive use of the heater
CENTER PANEL

CENTER PANEL
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED49
CENTER PANEL
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFFOFF
P
See section 5 in the Owner’s Manual for more information .
The Electric Parking Brake (EPB) system utilizes an electric motor to engage the parking brake .
Applying the Parking Brake
Depress the brake pedal and pull up the EPB switch A . Ensure that the indicator light is illuminated on the instrument cluster .
Releasing the Parking Brake
The EPB will automatically release when the brake pedal is engaged and shifter is shifted out of P (Park) to R (Reverse) or shifted out of N (Neutral) to Reverse or D (Drive) .
To release EPB manually, depress the brake pedal, then press the EPB switch A , with the ignition switch in the ON position . Ensure that the indicator light is OFF .
Electric Parking Brake (EPB)*
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electric Parking Brake / Auto Hold Video
QR CODE
•
Pull up and hold EPB switch again to increase brake pressure if parked on a decline or incline
•
When leaving your keys with parking lot at tendants or valet, make sure to inform them how to operate the EPB
•
If parked on a steep incline, pull up the EPB switch for more than 3 seconds for a firmer EPB application
QUICK TIPSREMINDERS:
•
The EPB malfunction indicator will illuminate for approximately 3 seconds as a bulb check when the ignition switch is turned ON
•
If the warning light does not illuminate temporarily or remains continuously lit, take your vehicle to an authorized Kia dealer and have the system checked
•
The EPB should not be operated while the vehicle is moving
•
A click or electric brake motor sound may be heard while operating or releasing the EPB . These conditions are normal and indicate that the EPB is functioning properly
•
EPB will not release unless the hood, liftgate and all doors are closed and seat belts are fastened
A

Automatic Turn Off Function
The interior lights automatically turn off approximately 20 seconds after the Engine Start/Stop button is
turned OFF .
Map/Room Lamp Operation
Map Lamps – Press lens A to turn the Driver ’s/Passenger ’s Map Lamps ON/OFF . This light produces a spot beam for convenient use as a map lamp or as a personal lamp for the driver or the front passenger .
Room button – Press button B to turn all the Map/Room Lamps ON/OFF .
Door button – Press button C to turn the Map/Room Lamp ON, for 30 seconds, when a door is opened, unlocked from Smart Key or the ignition is turned OFF . When pressed and a door is opened, or doors are unlocked from the Smart Key, the Map and Room Lamps turn ON for approximately 30 seconds .
The lamps will turn OFF immediately if the Engine Start/Stop button is turned ON or all doors are locked .
OTHER KEY FEATURES
Map/Room Lamps
See section 4 in the Owner’s Manual for more information .
*IF EQUIPPED58STINGER FEATURES & FUNCTIONS GUIDE
ABC
A
OTHER KEY

FEATURES
•
When doors are unlocked by the Smar t Key, the lamp turns ON for approximately 30 seconds
•
If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 3 seconds after the system is in armed stage
•
Using interior lights for an extended period of time may cause bat ter y discharge
QUICK TIPS
REMINDER: When room lamp lens is pressed ON it will remain ON, even when the map lamp switch is in the OFF position .
(Overhead lamp console)