change time KIA STONIC 2018 User Guide

3. Set the air intake control to theoutside air or recirculated air posi‐
tion.
4. Adjust the fan speed control and temperature control to maintain
maximum comfort.
CAUTION
•The refrigerant system should on‐ly be serviced by trained and certi‐fied technicians to insure properand safe operation.
•The refrigerant system should beserviced in a well-ventilated place.
•The air conditioning evaporator(cooling coil) shall never be re‐paired or replaced with one re‐moved from a used or salvagedvehicle and new replacement MACevaporators shall be certified (andlabeled) as meeting SAE StandardJ2842.
NOTICE
•When using the air conditioning
system, monitor the temperature
gauge closely while driving up hills
or in heavy traffic when outside
temperatures are high. Air condi‐
tioning system operation may
cause engine overheating. Contin‐
ue to use the blower fan but turn
the air conditioning system off if
the temperature gauge indicates
engine overheating.
•When opening the windows in hu‐
mid weather air conditioning may
create water droplets inside the
vehicle. Since excessive water
droplets may cause damage to
electrical equipment, air condition‐
ing should only be used with the
windows closed.
Air conditioning system operation tips
• If the vehicle has been parked in di‐ rect sunlight during hot weather,
open the windows for a short time to let the hot air inside the vehicle es‐
cape. • To help reduce moisture inside of the
windows on rainy or humid days, de‐
crease the humidity inside the vehicle
by operating the air conditioning sys‐ tem.
• During air conditioning system opera‐ tion, you may occasionally notice a
slight change in engine speed as the
air conditioning compressor cycles.
This is a normal system operation characteristic.
• Use the air conditioning system every month only for a few minutes to en‐
sure maximum system performance.
• When using the air conditioning sys‐ tem, you may notice clear waterdripping (or even puddling) on the
ground under the passenger side of
the vehicle. This is a normal system
operation characteristic.
• Operating the air conditioning system in the recirculated air position pro‐vides maximum cooling, however,
continual operation in this mode may
cause the air inside the vehicle to be‐
come stale.
• During cooling operation, you may oc‐ casionally notice a misty air flow be‐
cause of rapid cooling and humid air
intake. This is a normal system oper‐
ation characteristic.

4-115
4
Features of your vehicle

Climate control air filter (if
equipped)
A : Outside air
B : Recirculated air
C : Climate control air filterD : Blower
E : Evaporator core
F : Heater core
The climate control air filter installed
behind the glove box filters the dust or other pollutants that come into the ve‐
hicle from the outside through the
heating and air conditioning system. If dust or other pollutants accumulate
in the filter over a period of time, the
air flow from the air vents may de‐
crease, resulting in moisture accumula‐ tion on the inside of the windshield
even when the outside (fresh) air posi‐
tion is selected. If this happens, have the climate control air filter replaced by
a professional workshop. Kia recom‐
mends to visit an authorized Kia dealer/ service partner.
NOTICE
•Replace the filter according to the
Maintenance Schedule.
If the vehicle is being driven in se‐
vere conditions such as dusty or
rough roads, more frequent air
conditioner filter inspections and
changes are required.
•When the air flow rate suddenly
decreases, have the system
checked by a professional work‐
shop. Kia recommends to visit an
authorized Kia dealer/service part‐
ner.
Air Conditioning refrigerant label
¥
&YBNQMF
5ZQF
"
5ZQF
#
❈ The actual Air Conditioning refriger‐
ant label in the vehicle may differ
from the illustration.
Features of your vehicle
4-116

(Continued)
•To prevent overheating the seatwarmer, do not place anything onthe seats that insulates againstheat, such as blankets, cushions orseat covers while the seat warmeris in operation.
•Do not place heavy or sharp ob‐jects on seats equipped with seatwarmers. Damage to the seatwarming components could occur.
•Do not change the seat cover. Itmay damage the seat warmer orairventilation system.
WARNING
nSeat warmer burns
Passengers should use extreme cau‐tion when using seat warmers dueto the possibility of excess heatingor burns. The seat warmer maycause burns even at low tempera‐tures, especially if used for long pe‐riods of time. In particular, the drivermust exercise extreme care for thefollowing types of passengers:
(Continued)
(Continued)
1.Infants, children, elderly orhandicapped persons, or hospitaloutpatients
2.Persons with sensitive skin orthose that burn easily
3.Fatigued individuals
4.Intoxicated individuals
5.Individuals taking medicationthat can cause drowsiness orsleepiness (sleeping pills, coldtablets, etc.)
Power outlet
The power outlet is designed to provide
power for mobile telephones or other devices designed to operate with vehi‐
cle electrical systems. The devices
should draw less than 10 amps with the engine running.

4-129
4
Features of your vehicle

ENGINE EXHAUST CAN BE DANGEROUS!
WARNING
nENGINE EXHAUST CAN BE DANGEROUS!
Engine exhaust fumes can be extremely dangerous. If, at any time, you smell exhaust fumes inside the vehicle, open thewindows immediately.•Do not inhale exhaust fumes.Exhaust fumes contain carbon monoxide, a colorless, odorless gas that can cause unconsciousness and death by asphyx‐iation.
•Be sure the exhaust system does not leak.The exhaust system should be checked whenever the vehicle is raised to change the oil or for any other purpose. If youhear a change in the sound of the exhaust or if you drive over something that strikes the underneath side of the vehicle,have the system checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
•Do not run the engine in an enclosed area.Letting the engine idle in your garage, even with the garage door open, is a hazardous practice. Never run the engine inyour garage any longer than it takes to start the engine and back the vehicle out.
•Avoid idling the engine for prolonged periods with people inside the vehicle.If it is necessary to idle the engine for a prolonged period with people inside the vehicle, be sure to do so only in an openarea with the air intake set at "Fresh" and fan operating at one of the higher speeds so fresh air is drawn into the interi‐or.
If you must drive with the tailgate/trunk open because you are carrying objects that make this necessary:1.Close all windows.
2.Open side vents.
3.Set the air intake control at "Fresh", the air flow control at "Floor" or "Face" and the fan at one of the higher speeds.
To assure proper operation of the ventilation system, be sure the ventilation air intakes located just in front of the wind‐shield are kept clear of snow, ice, leaves or other obstructions.


6-03
6
Driving your vehicle

NOTICE
If you press the ENGINE START/
STOP button without depressing the
clutch pedal for manual transaxle
vehicles or without depressing the
brake pedal for automatic transaxle
vehicles, the engine will not start
and the engine start/stop button
changes as follow:
OFF ➔ACC ➔ ON ➔ OFF or ACC
NOTICE
If you leave the ENGINE START/STOP
button in the ACC or ON position for
a long time, the battery will dis‐
charge.
WARNING
•Never press the ENGINE START/STOP button while the vehicle is inmotion. This would result in loss ofdirectional control and brakingfunction, which could cause an ac‐cident.
•The anti-theft steering columnlock is not a substitute for theparking brake. Before leaving thedriver's seat, always make surethe shift lever is engaged in P(Park), set the parking brake fullyand shut the engine off. Unexpec‐ted and sudden vehicle movementmay occur if these precautions arenot taken.
•Never reach for the ENGINESTART/STOP button or any othercontrols through the steeringwheel while the vehicle is in mo‐tion. The presence of your hand orarm in the area could cause loss ofvehicle control, an accident and se‐rious bodily injury or death.
(Continued)
(Continued)
•Do not place any movable objectsaround the driver's seat as theymay move while driving, interferewith the driver and lead to an acci‐dent.
Starting the engine
WARNING
•Always wear appropriate shoeswhen operating your vehicle. Un‐suitable shoes (high heels, skiboots, etc.) may interfere withyour ability to use the brake andaccelerator pedal.
•Do not start the vehicle with theaccelerator pedal depressed. Thevehicle can move and lead to anaccident.
•Wait until the engine rpm is nor‐mal. The vehicle may suddenlymove if the brake pedal is releasedwhen the rpm is high.
Driving your vehicle
6-12

Disc brakes wear indicator
Your vehicle has disc brakes.
When your brake pads are worn andnew pads are required, you will hear a
high-pitched warning sound from your
front brakes or rear brakes. You may hear this sound come and go or it may
occur whenever you depress the brake
pedal.
Please remember that some driving conditions or climates may cause a
brake squeal when you first apply (or
lightly apply) the brakes. This is normal and does not indicate a problem with
your brakes.
CAUTION
•To avoid costly brake repairs, donot continue to drive with wornbrake pads.
•Always replace the front or rearbrake pads as pairs.
WARNING
nBrake wear
(Continued)
(Continued)
This brake wear warning soundmeans your vehicle needs service. Ifyou ignore this audible warning, youwill eventually lose braking perform‐ance, which could lead to a seriousaccident.
Rear drum brakes (if equipped)
Your rear drum brakes do not have
wear indicators. Therefore, have the rear brake linings inspected if you hear
a rear brake rubbing noise. Also have
your rear brakes inspected each time you change or rotate your tires and
when you have the front brakes re‐
placed.
Parking brake
Applying the parking brake
To engage the parking brake, first apply
the foot brake and then pull up the
parking brake lever as far as possible.
In addition it is recommended that when parking the vehicle on a incline,
the shift lever should be in a low gear
on manual transaxle vehicles or in the P (Park) position on automatic transaxle
vehicles.

6-31
6
Driving your vehicle

NOTICE
•When operating the vehicle on a
dynamometer, ensure that the
ESC is turned off (ESC OFF light il‐
luminated).
•Turning the ESC off does not af‐
fect ABS or brake system opera‐
tion.
WARNING
Never press the ESC OFF buttonwhile ESC is operating.If the ESC is turned off while ESC isoperating, the vehicle may go out ofcontrol.To turn ESC off while driving, pressthe ESC OFF button while driving ona flat road surface.
Hill-start assist control (HAC) (if
equipped)
Hill start Assist Control is a comfort
function. The main intend is to prevent the vehicle from rolling backwards
while driving off uphill on an inclined
surface. HAC holds the braking pressure
builtup by driver during stopping proce‐ dure for 2 seconds after releasing
brake pedal.
During the pressure-hold period, the
driver has enough time to press the ac‐ celerator pedal to drive off.
The braking pressure is reduced as
soon as the system detects the driver’s
intention to drive off.
WARNING
The HAC is usually activated only for2 seconds. The driver should becareful from the rolling backwardcausing the accident with behind ob‐jects or human, when the driver mayfeel the unintended rolling backwardwhile driving off on hill due to insuf‐ficient brake hold pressure built-upby driver during stopping procedure.
NOTICE
•The HAC does not operate when
the transaxle shift lever is in the P
(Park) or N (Neutral) position.
•The HAC activates even though
the ESC is off but it does not acti‐
vate when the ESC has malfunc‐
tioned.
Vehicle stability management
(VSM) (if equipped)
This system provides further enhance‐
ments to vehicle stability and steering responses when a vehicle is driving on a
slippery road or a vehicle detected
changes in coefficient of friction be‐ tween right wheels and left wheels
when braking.
VSM operation
When the VSM is in operation, ESC indi‐
cator light () blinks.
When the vehicle stability management
is operating properly, you can feel a slight pulsation in the vehicle. This is
only the effect of brake control and in‐
dicates nothing unusual.

6-39
6
Driving your vehicle

Follow either of these procedures:• Move the lever down (to SET-) and hold it. Your vehicle will gradually
slow down. Release the lever at the speed you want to maintain.
• Move the lever down (to SET-) and release it immediately. The cruising
speed will decrease by 2.0 km/h (1.2
mph) each time you move the lever
down (to SET-) in this manner.
To temporarily accelerate with
the cruise control on:
If you want to speed up temporarily when the cruise control is on, depress
the accelerator pedal. Increased speed
will not interfere with cruise control op‐ eration or change the set speed.
To return to the set speed, take your
foot off the accelerator pedal.
To cancel cruise control, do one
of the following:
¥
5ZQF
"
¥
5ZQF
#

6-47
6
Driving your vehicle

Remember that trailering is different
than just driving your vehicle by itself. Trailering means changes in handling,
durability, and fuel economy. Success‐
ful, safe trailering requires correct equipment, and it has to be used prop‐
erly.
This section contains many time-tes‐
ted, important trailering tips and safety
rules. Many of these are important for your safety and that of your passen‐
gers. Please read this section carefully
before you pull a trailer.
Load-pulling components such as the engine, transaxle, wheel assemblies,
and tires are forced to work harder
against the load of the added weight. The engine is required to operate at
relatively higher speeds and under
greater loads. This additional burden generates extra heat. The trailer also
considerably adds wind resistance, in‐
creasing pulling requirements.
0:#%
NOTICE
nLocation of trailer mounting
CUV
After removing rear bumper and
back beam, hitch equipment can be
installed. The rear bumper should be
reinstalled after completion of hitch
equipment installation.
Hitches
It's important to have the correct hitch
equipment. Crosswinds, large trucks going by, and rough roads are a few
reasons why you’ll need the right hitch.
Here are some rules to follow: • Do you have to make any holes in the
body of your vehicle when you installa trailer hitch? If you do, then be sure
to seal the holes later when you re‐
move the hitch.
If you don’t seal them, deadly carbon
monoxide (CO) from your exhaust can get into your vehicle, as well as
dirt and water.
• The bumpers on your vehicle are not intended for hitches. Do not attach
rental hitches or other bumper-type
hitches. Use only a frame-mounted hitch that does not attach to the
bumper.
• Kia trailer hitch accessary is available at an authorized Kia dealer/service
partner.
Safety chains
You should always attach chains be‐
tween your vehicle and your trailer. Cross the safety chains under the
tongue of the trailer so that the tongue
will not drop to the road if it becomes separated from the hitch.

6-87
6
Driving your vehicle

Making turns
When you’re turning with a trailer,
make wider turns than normal. Do this so your trailer won’t strike soft should‐
ers, curbs, road signs, trees, or other
objects. Avoid jerky or sudden maneu‐ vers. Signal well in advance.
Turn signals when towing a trailer
When you tow a trailer, your vehicle
has to have a different turn signal flasher and extra wiring. The green ar‐
rows on your instrument panel will
flash whenever you signal a turn or lane change. Properly connected, the
trailer lights will also flash to alert oth‐
er drivers you’re about to turn, change lanes, or stop.
When towing a trailer, the green ar‐
rows on your instrument panel will
flash for turns even if the bulbs on the trailer are burned out. Thus, you may
think drivers behind you are seeing
your signals when, in fact, they are not. It’s important to check occasionally to
be sure the trailer bulbs are still work‐
ing. You must also check the lights ev‐ ery time you disconnect and then re‐
connect the wires.
Do not connect a trailer lighting system
directly to your vehicle’s lighting sys‐ tem. Use only an approved trailer wir‐
ing harness. Have yourself assisted by a professio‐
nal workshop in installing the wiring harness.
Kia recommends to visit an authorized
Kia dealer/service partner.
WARNING
Failure to use an approved trailerwiring harness could result in dam‐age to the vehicle electrical systemand/or personal injury.
Driving on grades
Reduce the speed and shift to a lower
gear before you start down a long or steep downgrade. If you don’t shift
down, you might have to use your
brakes so much that they would get hot and no longer operate efficiently.
On a long uphill grade, shift down and
reduce your speed to around 70 km/h
(45 mph) to reduce the possibility of engine and transaxle overheating.
If your trailer weighs more than the
maximum trailer weight without trailer
brakes and you have an automatic transaxle, you should drive in D (Drive)
when towing a trailer. Operating your vehicle in D (Drive)
when towing a trailer will minimize heat build up and extend the life of
your transaxle.
CAUTION
•When towing a trailer on steepgrades (in excess of 6%) pay closeattention to the engine coolanttemperature gauge to ensure theengine does not overheat. If theneedle of the coolant temperaturegauge moves across the dial to‐wards L