warning lights KIA STONIC 2018 User Guide

INSTRUMENT CLUSTER
0:#0:#$
5ZQF
"
5ZQF
#
1. Tachometer
2. Speedometer
3. Engine coolant temperature gauge
4. Fuel gauge
5. Warning and indicator lights
6. LCD display
❈ The actual cluster in the vehicle
may differ from the illustration.
For more details, refer to L

0:#0:#
5ZQF
$
5ZQF
%
1. Tachometer
2. Speedometer
3. Engine coolant temperature gauge
4. Fuel gauge
5. Warning and indicator lights
6. LCD display
❈ The actual cluster in the vehicle
may differ from the illustration.
For more details, refer to L

WARNING AND INDICATOR LIGHTS
Warning lights
NOTICE
nWarning lights
Make sure that all warning lights are
OFF after starting the engine. If any
light is still ON, this indicates a situa‐
tion that needs attention.
Air bag Warning Light
This warning light illumi‐nates:
• Once you set the ignition switch or Engine Start/Stop Button
to the ON position. - It illuminates for approximately 6 seconds and then goes off.
• When there is a malfunction with the SRS.
In this case, have the vehicle inspec‐
ted by a professional workshop. Kia
recommends to visit an authorized
Kia dealer/service partner.
Seat Belt Warning Light
This warning light informs the driver that the seat belt
is not fastened.
❈ For more details, refer to the L

WARNING
nParking Brake & Brake FluidWarning Light
Driving the vehicle with a warninglight ON is dangerous. If the ParkingBrake & Brake Fluid Warning Light il‐luminates with the parking brake re‐leased, it indicates that the brakefluid level is low.In this case, have the vehicle inspec‐ted by a professional workshop. Kiarecommends to visit an authorizedKia dealer/service partner.
Anti-lock Brake System
(ABS) Warning Light
This warning light illumi‐nates:
• Once you set the ignition switch or Engine Start/Stop button to the ON
position. - It illuminates for approximately 3 seconds and then goes off.
• When there is a malfunction with theABS (the normal braking system will
still be operational without the assis‐ tance of the anti-lock brake system).
In this case, have the vehicle inspec‐
ted by a professional workshop. Kia
recommends to visit an authorized
Kia dealer/service partner.
Electronic Brake force
Distribution (EBD)
System Warning Light
These two warning lights il‐luminate at the same timewhile driving:
• When the ABS and regular brake system may not
work normally.
In this case, have the vehicle inspec‐ ted by a professional workshop. Kia
recommends to visit an authorized
Kia dealer/service partner.
WARNING
nElectronic Brake force Distri‐bution (EBD) system warninglight
(Continued)
(Continued)
When both ABS and Parking Brake &Brake Fluid Warning Lights are on,the brake system will not work nor‐mally and you may experience anunexpected and dangerous situationduring sudden braking.In this case, avoid high speed drivingand abrupt braking.Have the vehicle inspected by a pro‐fessional workshop as soon as possi‐ble. Kia recommends to visit an au‐thorized Kia dealer/service partner.
NOTICE
nElectronic Brake force Distri‐
bution (EBD) system warning
light
When the ABS Warning Light is on or
both ABS and Parking Brake & Brake
Fluid Warning Lights are on, the
speedometer, odometer, or tripme‐
ter may not work. Also, the EPS
Warning Light may illuminate and
(Continued)
Features of your vehicle
4-66

The high beam indicator will light when
the headlight high beams are switched on. To prevent the battery from being
discharged, do not leave the lights on
for a prolonged time while the engine is not running.
WARNING
Do not use high beam when thereare other vehicles. Using high beamcould obstruct the other driver's vi‐sion.
¥
5ZQF
"
To flash the headlights, pull the lever
towards you. It will return to the nor‐ mal (low beam) position when released.
The headlight switch does not need to
be on to use this flashing feature .
Turn signals and lane change
signals
¥
5ZQF
"
¥
5ZQF
#
Features of your vehicle
4-84

INTERIOR LIGHT
CAUTION
Do not use the interior lights for ex‐tended periods when the engine isnot running.It may cause battery discharge.
WARNING
Do not use the interior lights whendriving in the dark. Accidents couldhappen because the view may beobscured by interior lights.
Map lamp
¥
5ZQF
"
¥
5ZQF
#
• (1) : Press the lamps to turn thefront map lamps on and off. •
(2):
- The map lamp and room lamp comes on when a door is opened.
The lamps go out after approxi‐
mately 30 seconds.
- The map lamp and room lamp comes on for approximately 30
seconds when doors are unlocked
with a transmitter or smart key as
long as the doors are not opened.
- The map lamp and room lamp will stay on for approximately 20 mi‐
nutes if a door is opened with the
ignition switch in the ACC or
LOCK/OFF position.
- The map lamp and room lamp will stay on continuously if the door is
opened with the ignition switch inthe ON position.
- The map lamp and room lamp will go out immediately if the ignition
switch is changed to the ON posi‐
tion or all doors are locked.
- To turn off the DOOR mode, press the DOOR button (2) once again
(not pressed).

4-95
4
Features of your vehicle

KEY POSITIONS
Ignition switch position
LOCK
0:##
5ZQF
"
-0$, "$$
0/
45"35
¥
5ZQF
#
The steering wheel locks to protect
against theft. The ignition key can be removed only in the LOCK position.
ACC (Accessory)
The steering wheel is unlocked and
electrical accessories are operative.
NOTICE
If difficulty is experienced turning
the ignition switch to the ACC posi‐
tion, turn the key while turning the
steering wheel right and left to re‐
lease the tension.
ON
The warning lights can be checked be‐
fore the engine is started. This is the normal running position after the en‐
gine is started.
Do not leave the ignition switch ON if
the engine is not running to prevent battery discharge.
START
Turn the ignition switch to the START
position to start the engine. The engine will crank until you release the key;
then it returns to the ON position. The
brake warning light can be checked in this position.
WARNING
nIgnition switch
•Never turn the ignition switch toLOCK or ACC while the vehicle ismoving. This would result in loss ofdirectional control and brakingfunction, which could cause an ac‐cident.
(Continued)
Driving your vehicle
6-06

(Continued)
GINE START/STOP button while
turning the steering wheel right and
left to release the tension.
•If difficulty is experienced turning
the engine start/stop button to
the ACC position, turn the steering
wheel right and left to release the
tension while pressing the engine
start/stop button.
•When you turn off the engine, the
vehicle should be stopped.
CAUTION
You are able to turn off the engine(START/RUN) or vehicle power (ON),only when the vehicle is not in mo‐tion. In an emergency situation whilethe vehicle is in motion, you are ableto turn the engine off and to theACC position by pressing the enginestart/stop button for more than 2seconds or 3 times successivelywithin 3 seconds. If the vehicle is stillmoving, you can restart the engine
(Continued)
(Continued)
without depressing the brake pedalby pressing the engine start/stopbutton with the shift lever in the N(Neutral) position.
ACC (Accessory)
With manual transaxle
Press the engine start/stop button when the button is
in the OFF position without depressing the clutch pedal.
With automatic transaxle
Press the ENGINE START/STOP button
while it is in the OFF position without depressing the brake pedal.
The steering wheel unlocks and electri‐
cal accessories are operational.
If the ENGINE START/STOP button is in
the ACC position for more than 1 hour, the button is turned off automatically
to prevent battery discharge.
0SBOHF
ON
With manual transaxle
Press the engine start/stop button when the button is
in the ACC position without depressing the clutch pedal.
3FE
With automatic transaxle
Press the ENGINE START/STOP button
while it is in the ACC position without depressing the brake pedal.
The warning lights can be checked be‐
fore the engine is started. Do not leave
the ENGINE START/STOP button in the ON position for a long time. The bat‐
tery may discharge, because the engineis not running.
START/RUN
With manual transaxle
To start the engine, depress the clutch pedal and brake
pedal, then press the engine start/stop button with theshift lever in the N (Neutral) position.
With automatic transaxle
To start the engine, depress the brake
pedal and press the engine start/stop
button with the shift lever in the P (Park) or the N (Neutral) position. For
your safety, start the engine with the
shift lever in the P (Park) position.
/PU
JMMVNJOBUFE

6-11
6
Driving your vehicle

ISG (IDLE STOP AND GO) SYSTEM (IF EQUIPPED)
Your vehicle may be equipped with the
ISG system, which reduces fuel con‐ sumption by automatically shutting
down the engine, when the vehicle is at
a standstill. (For example : red light, stop sign and traffic jam)
The engine starts automatically as
soon as the starting conditions are
met.
The ISG system is ON whenever the en‐ gine is running.
NOTICE
When the engine automatically
starts by the ISG system, some
warning lights (ABS, ESC, ESC OFF,
EPS or Parking brake warning light)
may turn on for a few seconds.
This happens because of low battery
voltage. It does not mean the sys‐
tem is malfunctioning.
Auto stop
To stop the engine in idle stop
mode
• Manual transaxle 1. Decrease the vehicle speed to less than 5 km/h.
2. Shift into N (Neutral) position.
3. Release the clutch pedal.
• Automatic transaxle 1. Decrease the vehicle speed to less than 5 km/h.
2. Press the brake pedal. The engine will stop and the green AU‐
TO STOP indicator (
) on the instru‐
ment cluster will illuminate. If your ve‐ hicle is equipped with a supervision
cluster, the notice will illuminate on the
LCD display.
Driving your vehicle
6-16

(Continued)
•The FCA operates only for the ve‐hicle / pedestrian in front, whiledriving forward. It does not oper‐ate for any animals or vehicles inthe opposite direction.
•The FCA does not recognize thevehicle, which horizontally drivesacross the crossroad, or the vehi‐cle, which is parked in the horizon‐tal direction.
Limitation of the system
The FCA is an assistant system for a
driver in a certain risky driving condition
and it does not take every responsibili‐ ty for all risks from driving condition.
The FCA monitors the driving situations
through the radar and the camera sen‐
sor. Thus, for a situation out of the sensing range, the FCA may not nor‐
mally operate. The driver should pay
great caution in the following situa‐ tions. The FCA operation may be limi‐
ted.
Recognizing vehicles
- The radar or the camera is contami‐
nated with foreign substances.
- It heavily rains or snows. -
There is interruption by electric
waves.
- There is severe irregular reflection
from the radar.
- The vehicle in front has a narrow
body. (i.e. motor cycle and bicycle)
- The driver’s view is unclear due to
the backlight, the reflected light, or
darkness.
- The camera cannot contain the full
image of the vehicle in front.
- The vehicle in front is a special vehi‐
cle, such as a heavily-loaded truck or
a trailer.
The vehicle in front does not turn ON
the rear lights, does not have rear
lights, has asymmetric rear lights, or
has rear lights out of angle.
- The outside brightness is greatly
changed, such as entering/exiting the tunnel.
- The vehicle driving is unstable.
- The radar/camera sensor recognition
is limited.
- Driving on unpaved and uneven road
surfaces, or through sudden gradient changes. -
In construction zones or on railroad
tracks, or there are metallic objects
on the road.
- Driving indoors such as in an under‐
ground parking lot.
- Driving on a curve
The FCA performance decreases
while driving on a curve. The FCA may
not recognize the vehicle in front even in the same lane. It may unnec‐
essarily produce the warning mes‐
sage and the warning alarm, or it
may not produce the warning mes‐
sage and the warning alarm at all.
While driving on a curve, pay great caution, and, if necessary, depress
the brake pedal.
Driving your vehicle
6-58