battery KIA STONIC 2018 Owner's Manual

1. Turn the ignition switch to the ONposition.
2. Turn the mode selection knob to the defrost position (
).
3. Push the air intake control button at least 5 times within 3 seconds.
The indicator light in the air intake con‐
trol button will blink 3 times. It indi‐ cates that the defogging logic is can‐
celed or returned to the programmed
status.
If the battery has been discharged or disconnected, it resets to the defog
logic status.
Automatic climate control system
(if equipped)
1. Turn the ignition switch to the ON position.
2. Select the defrost position pressing defrost button (
).
3. While holding the air conditioning button (A/C) pressed, press the air
intake control button at least 5
times within 3 seconds.
The A/C display blinks 3 times. It indi‐ cates that the defogging logic is can‐
celed or returned to the programmed
status.
If the battery has been discharged or disconnected, it is reset to the defog
logic status.
Auto defogging system (Only for
automatic climate control system,
if equipped)
Auto defogging reduces the possibility
of fogging up the inside of the wind‐ shield by automatically sensing the
moisture of inside the windshield and
air flow toward the windshield can in‐ crease.
The auto defogging system operates
when the AUTO mode is on.
For Europe
If your vehicle is equipped with the auto
defogging system, it is automatically
activated when the conditions are met.
Features of your vehicle
4-120

CAUTION
•Use the power outlet only whenthe engine is running and removethe accessory plug after use. Usingthe accessory plug for prolongedperiods of time with the engine offcould cause the battery to dis‐charge.
•Only use 12V electric accessorieswhich are less than 10A in electriccapacity.
•Adjust the air-conditioner or heat‐er to the lowest operating levelwhen using the power outlet.
•Close the cover when not in use.
•Some electronic devices can causeelectronic interference when plug‐ged into a vehicle’s power outlet.These devices may cause exces‐sive audio static and malfunctionsin other electronic systems or de‐vices used in your vehicle.
•Using electrical products which ex‐ceed the limited capacity mightcause heating to the power outletand wiring that could lead to anelectrical breakdown.
(Continued)
(Continued)
•Always make sure the electricalpart is firmly plugged into thepower outlet. Incomplete pluggingmay cause electrical breakdown.
•Electrical products with a built-inbattery might cause current flow,which could lead to malfunction ofthe electric/ electronic device inyour vehicle. Only use electricalproducts which include reversecurrent prevention.
WARNING
Do not put a finger or a foreign ele‐ment (pin, etc.) into a power outletand do not touch with a wet hand.You may get an electric shock.
USB charger (if equipped)
The USB charger is designed to re‐
charge batteries of small size electrical devices using a USB cable. The electrical
devices can be recharged when the En‐
gine Start/Stop button is in ACC/ON/ START position.
The battery charging state may be
monitored on the electrical device.
Disconnect the USB cable from the USB
port after use. • Some devices are not supported for fast charging but will be charged withnormal speed.
• Use the USB charger when the engine is running to prevent battery dis‐
charge.
Features of your vehicle
4-130

• Only devices that fits the USB portcan be used.
• The USB charger can be used only for battery charging purposes.
• Battery chargers cannot be charged.
Floor mat anchor(s) (if
equipped)
0:#
When using a floor mat on the front
floor carpet, make sure it attaches to the floor mat anchor(s) in your vehicle.
This keeps the floor mat from sliding
forward.
WARNING
The following must be observedwhen installing ANY floor mat to thevehicle.•Ensure that the floor mats are se‐curely attached to the vehicle'sfloor mat anchor(s) before drivingthe vehicle.
•Do not use ANY floor mat thatcannot be firmly attached to thevehicle's floor mat anchors.
•Do not stack floor mats on top ofone another (e.g. all-weather rub‐ber mat on top of a carpeted floormat). Only a single floor matshould be installed in each position.
IMPORTANT - Your vehicle was man‐ufactured with driver's side floormat anchors that are designed tosecurely hold the floor mat in place.To avoid any interference with pedaloperation, Kia recommends that onlythe Kia floor mat designed for use inyour vehicle be installed.
Shopping bag holder
CAUTION
•Do not hang a bag weighing morethan 3 kg (7 lbs.). It may causedamage to the shopping bag hold‐er.
•Do not hang the frail objects whenyou drive rough road, the objectsmay be damaged.

4-131
4
Features of your vehicle

The Lane Departure Warning (LDW) System
does not operate when:....................................................... 6-64
The Lane Departure Warning (LDW) System
may not warn you even if the vehicle leaves the
lane, or may warn you even if the vehicle does
not leave the lane when:......................................................6-64
Driver Attention Warning (DAW) system (if equipped) ..... 6-66
System setting and activation............................................6-66
Resetting the system.......................................................... 6-67
System standby.................................................................... 6-67
System malfunction............................................................. 6-68
Blind-Spot Collision Warning (BCW) ...................................... 6-70 BCW (Blind-Spot Collision Warning) / LCA (Lane
Change Assist)....................................................................... 6-71
Rear Cross-Traffic Collision Warning................................. 6-73
Driver's attention.................................................................. 6-75
Economical operation............................................................... 6-76
Special driving conditions......................................................... 6-78 Hazardous driving conditions.............................................. 6-78
Rocking the vehicle............................................................... 6-78
Smooth cornering................................................................. 6-79
Driving at night...................................................................... 6-79
Driving in the rain.................................................................. 6-80
Driving in flooded areas....................................................... 6-80
Driving off-road.................................................................... 6-81
Highway driving..................................................................... 6-81
Winter driving............................................................................ 6-82 Snowy or icy conditions....................................................... 6-82
Use high quality ethylene glycol coolant...........................6-84
Check battery and cables.................................................... 6-84 Change to "winter weight" oil if necessary...................... 6-84
Check spark plugs and ignition system............................. 6-84
To keep locks from freezing................................................ 6-85
Use approved window washer anti-freeze in system.... 6-85
Don't let your parking brake freeze...................................6-85
Don't let ice and snow accumulate underneath.............. 6-85
Carry emergency equipment.............................................. 6-85
Trailer towing (for Europe)...................................................... 6-86 Hitches.................................................................................... 6-87
Safety chains......................................................................... 6-87
Trailer brakes......................................................................... 6-88
Driving with a trailer............................................................. 6-88
Maintenance when trailer towing...................................... 6-91
If you do decide to pull a trailer.......................................... 6-91
Vehicle weight............................................................................ 6-94 Base curb weight.................................................................. 6-94
Vehicle curb weight...............................................................6-94
Cargo weight.......................................................................... 6-94
GAW (Gross axle weight)..................................................... 6-94
GAWR (Gross axle weight rating)....................................... 6-94
GVW (Gross vehicle weight)................................................ 6-94
GVWR (Gross vehicle weight rating).................................. 6-94
Overloading............................................................................ 6-94


6

KEY POSITIONS
Ignition switch position
LOCK
0:##
5ZQF
"
-0$, "$$
0/
45"35
¥
5ZQF
#
The steering wheel locks to protect
against theft. The ignition key can be removed only in the LOCK position.
ACC (Accessory)
The steering wheel is unlocked and
electrical accessories are operative.
NOTICE
If difficulty is experienced turning
the ignition switch to the ACC posi‐
tion, turn the key while turning the
steering wheel right and left to re‐
lease the tension.
ON
The warning lights can be checked be‐
fore the engine is started. This is the normal running position after the en‐
gine is started.
Do not leave the ignition switch ON if
the engine is not running to prevent battery discharge.
START
Turn the ignition switch to the START
position to start the engine. The engine will crank until you release the key;
then it returns to the ON position. The
brake warning light can be checked in this position.
WARNING
nIgnition switch
•Never turn the ignition switch toLOCK or ACC while the vehicle ismoving. This would result in loss ofdirectional control and brakingfunction, which could cause an ac‐cident.
(Continued)
Driving your vehicle
6-06

(Continued)
GINE START/STOP button while
turning the steering wheel right and
left to release the tension.
•If difficulty is experienced turning
the engine start/stop button to
the ACC position, turn the steering
wheel right and left to release the
tension while pressing the engine
start/stop button.
•When you turn off the engine, the
vehicle should be stopped.
CAUTION
You are able to turn off the engine(START/RUN) or vehicle power (ON),only when the vehicle is not in mo‐tion. In an emergency situation whilethe vehicle is in motion, you are ableto turn the engine off and to theACC position by pressing the enginestart/stop button for more than 2seconds or 3 times successivelywithin 3 seconds. If the vehicle is stillmoving, you can restart the engine
(Continued)
(Continued)
without depressing the brake pedalby pressing the engine start/stopbutton with the shift lever in the N(Neutral) position.
ACC (Accessory)
With manual transaxle
Press the engine start/stop button when the button is
in the OFF position without depressing the clutch pedal.
With automatic transaxle
Press the ENGINE START/STOP button
while it is in the OFF position without depressing the brake pedal.
The steering wheel unlocks and electri‐
cal accessories are operational.
If the ENGINE START/STOP button is in
the ACC position for more than 1 hour, the button is turned off automatically
to prevent battery discharge.
0SBOHF
ON
With manual transaxle
Press the engine start/stop button when the button is
in the ACC position without depressing the clutch pedal.
3FE
With automatic transaxle
Press the ENGINE START/STOP button
while it is in the ACC position without depressing the brake pedal.
The warning lights can be checked be‐
fore the engine is started. Do not leave
the ENGINE START/STOP button in the ON position for a long time. The bat‐
tery may discharge, because the engineis not running.
START/RUN
With manual transaxle
To start the engine, depress the clutch pedal and brake
pedal, then press the engine start/stop button with theshift lever in the N (Neutral) position.
With automatic transaxle
To start the engine, depress the brake
pedal and press the engine start/stop
button with the shift lever in the P (Park) or the N (Neutral) position. For
your safety, start the engine with the
shift lever in the P (Park) position.
/PU
JMMVNJOBUFE

6-11
6
Driving your vehicle

NOTICE
If you press the ENGINE START/
STOP button without depressing the
clutch pedal for manual transaxle
vehicles or without depressing the
brake pedal for automatic transaxle
vehicles, the engine will not start
and the engine start/stop button
changes as follow:
OFF ➔ACC ➔ ON ➔ OFF or ACC
NOTICE
If you leave the ENGINE START/STOP
button in the ACC or ON position for
a long time, the battery will dis‐
charge.
WARNING
•Never press the ENGINE START/STOP button while the vehicle is inmotion. This would result in loss ofdirectional control and brakingfunction, which could cause an ac‐cident.
•The anti-theft steering columnlock is not a substitute for theparking brake. Before leaving thedriver's seat, always make surethe shift lever is engaged in P(Park), set the parking brake fullyand shut the engine off. Unexpec‐ted and sudden vehicle movementmay occur if these precautions arenot taken.
•Never reach for the ENGINESTART/STOP button or any othercontrols through the steeringwheel while the vehicle is in mo‐tion. The presence of your hand orarm in the area could cause loss ofvehicle control, an accident and se‐rious bodily injury or death.
(Continued)
(Continued)
•Do not place any movable objectsaround the driver's seat as theymay move while driving, interferewith the driver and lead to an acci‐dent.
Starting the engine
WARNING
•Always wear appropriate shoeswhen operating your vehicle. Un‐suitable shoes (high heels, skiboots, etc.) may interfere withyour ability to use the brake andaccelerator pedal.
•Do not start the vehicle with theaccelerator pedal depressed. Thevehicle can move and lead to anaccident.
•Wait until the engine rpm is nor‐mal. The vehicle may suddenlymove if the brake pedal is releasedwhen the rpm is high.
Driving your vehicle
6-12

(Continued)
tion. If the traffic and road condi‐tions permit, you may put the shiftlever in the N (Neutral) position whilethe vehicle is still moving and pressthe ENGINE START/STOP button inan attempt to restart the engine.
NOTICE
•If the battery is weak or the smart
key does not work correctly, you
can start the engine by pressing
the engine start/stop button with
the smart key.
•When the brake switch fuse is
blown, you can't start the engine
normally. Replace the fuse with a
new one. If it is not possible, you
can start the engine by pressing
the ENGINE START/STOP button
for 10 seconds while it is in the
ACC position. The engine can start
without depressing the brake ped‐
al. But for your safety always de‐
press the brake pedal before
starting the engine.
CAUTION
Do not press the ENGINE START/STOP button for more than 10 sec‐onds except when the stop lampfuse is blown.

6-15
6
Driving your vehicle

ISG (IDLE STOP AND GO) SYSTEM (IF EQUIPPED)
Your vehicle may be equipped with the
ISG system, which reduces fuel con‐ sumption by automatically shutting
down the engine, when the vehicle is at
a standstill. (For example : red light, stop sign and traffic jam)
The engine starts automatically as
soon as the starting conditions are
met.
The ISG system is ON whenever the en‐ gine is running.
NOTICE
When the engine automatically
starts by the ISG system, some
warning lights (ABS, ESC, ESC OFF,
EPS or Parking brake warning light)
may turn on for a few seconds.
This happens because of low battery
voltage. It does not mean the sys‐
tem is malfunctioning.
Auto stop
To stop the engine in idle stop
mode
• Manual transaxle 1. Decrease the vehicle speed to less than 5 km/h.
2. Shift into N (Neutral) position.
3. Release the clutch pedal.
• Automatic transaxle 1. Decrease the vehicle speed to less than 5 km/h.
2. Press the brake pedal. The engine will stop and the green AU‐
TO STOP indicator (
) on the instru‐
ment cluster will illuminate. If your ve‐ hicle is equipped with a supervision
cluster, the notice will illuminate on the
LCD display.
Driving your vehicle
6-16

The engine will also restart
automatically without the driver's
any actions if the following occurs:
-The fan speed of manual climate con‐
trol system is set above the 3rd posi‐
tion when the air conditioning is on.
- The fan speed of automatic climate
control system is set above the 6th
position when the air conditioning is on.
- When a certain amount of time has
passed with the climate control sys‐
tem on.
- When the defroster is on.
- The brake vacuum pressure is low.
- The battery charging status is low.
- The vehicle speed exceeds 5 km/h.
The green AUTO STOP indicator (
) on
the instrument cluster will blink for 5
seconds.
Condition of ISG system
operation
The ISG system will operate under
the following condition:
- The driver’s seat belt is fastened. -
The driver’s door and hood are closed.
- The brake vacuum pressure is ade‐
quate.
- The battery is sufficiently charged.
- The outside temperature is more
than -2°C (28.4°F).
- The outside temperature is under
32°C (89.6°F).
- The engine coolant temperature is
not too low.
NOTICE
•If the ISG system does not meet
that operation condition, the ISG
system is deactivated. The light on
the ISG OFF button will illuminate.
•If the light comes on continuously,
please check the operation condi‐
tion.
ISG system deactivation
• If you want to deactivate the ISG system, press the ISG OFF button.
The light on the ISG OFF button will il‐ luminate.
Driving your vehicle
6-18