display KIA STONIC 2018 Owner's Manual
[x] Cancel search | Manufacturer: KIA, Model Year: 2018, Model line: STONIC, Model: KIA STONIC 2018Pages: 523, PDF Size: 24.99 MB
Page 247 of 523
(Continued)
•Always check the surroundingareas near your vehicle for people,especially children, before shiftinga car into D (Drive) or R (Reverse).
•Before leaving the driver’s seat, al‐ways make sure the shift lever isin the P (Park) position; then setthe parking brake fully and shutthe engine off. Unexpected andsudden vehicle movement can oc‐cur if these precautions are notfollowed in the order identified.
•Do not use the engine brake (shift‐ing from a high gear to lower gear)rapidly on slippery roads.The vehicle may slip causing an ac‐cident.
CAUTION
•To avoid damage to your trans‐axle, do not accelerate the enginein R (Reverse) or any forward gearposition with the brakes on.
(Continued)
(Continued)
•When stopped on an incline, do nothold the vehicle stationary withengine power.Use the service brake or the park‐ing brake.
•Do not shift from N (Neutral) or P(Park) into D (Drive), or R (Reverse)when the engine is above idlespeed.
Transaxle ranges
The indicator in the instrument cluster
displays the shift lever position when the ignition switch is in the ON position.
P (Park)
Always come to a complete stop before
shifting into P (Park). This position
locks the transaxle and prevents the drive wheels from rotating.
WARNING
•Shifting into P (Park) while the ve‐hicle is in motion will cause thedrive wheels to lock which willcause you to lose control of thevehicle.
•Do not use the P (Park) position inplace of the parking brake. Alwaysmake sure the shift lever is latch‐ed in the P (Park) position and setthe parking brake fully.
•Never leave a child unattended in avehicle.
CAUTION
The transaxle may be damaged ifyou shift into P (Park) while the ve‐hicle is in motion.
R (Reverse)
Use this position to drive the vehicle
backward.
6-25
6
Driving your vehicle
Page 273 of 523
3. Move the lever up (to RES+) ordown (to SET-), and release it at
the desired speed. Move the lever
up (to RES+) or down (to SET-) and
hold it. The speed will increase or
decrease by 5 km/h (3 mph).
The set speed limit will be displayed.
To drive over the preset speed limit you
must depress hard on the accelerator pedal (more than approximately 80%)
until the kick down mechanism works
with a clicking noise. Then the set speed limit will blink and chime will
sound until you return the vehicle
speed within the speed limit.
NOTICE
•Depressing the accelerator pedal
less than approximately 50%, the
vehicle will not speed over the pre‐
set speed limit but maintain the
vehicle speed within the speed lim‐
it.
•A clicking noise heard from the
kick down mechanism by depress‐
ing the accelerator pedal fully is a
normal condition.
To turn off the speed limit
control, do one of the following:
6-51
6
Driving your vehicle
Page 275 of 523
FORWARD COLLISION-AVOIDANCE ASSIST (FCA) SYSTEM (IF EQUIPPED)
The FCA system is to reduce or to avoid
accident risk. It recognizes the distance
from the vehicle ahead or the pedes‐ trian through the sensors (i.e. radar
and camera), and, if necessary, warns
the driver of accident risk with the warning message or the warning
alarms.
WARNING
Take the following precautions whenusing the Forward Collision-Avoid‐ance Assist (FCA) System:•This system is only a supplemen‐tal system and it is not intendedto, nor does it replace the need forextreme care and attention of thedriver. The sensing range and ob‐jects detectable by the sensors arelimited. Pay attention to the roadconditions at all times.
•NEVER drive too fast in accordancewith the road conditions or whilecornering.
(Continued)
(Continued)
•Always drive cautiously to preventunexpected and sudden situationsfrom occurring. FCA does not stopthe vehicle completely and doesnot avoid collisions.
System setting and activation
System setting
The driver can activate the FCA by plac‐
ing the ignition switch to the ON posi‐
tion and by selecting 'User Settings', 'Driving Assist', and 'Forward Collision-
Avoidance Assist (FCA)'. The FCA deac‐
tivates, when the driver cancels the system setting.
The warning light illuminates on the LCD display, when youcancel the FCA system.
The driver can monitor the FCAON/OFF status on the LCD display.
When the warning light remains ON
with the FCA activated, have the sys‐tem checked by a professional work‐
shop. Kia recommends to visit an au‐
thorized Kia dealer/service partner. The driver can select the initial warning
activation time in the User Settings and Driving Assist in the instrument cluster
LCD display. The options for the initial
Forward Collision Warning include the following:
• EARLY - When this condition is se‐
lected, the initial Forward
Collision Warning is activa‐ted earlier than normal.This setting maximizesthe amount of distance
between the vehicle or
pedestrian ahead beforethe initial warning occurs.
• NORMAL - When this condition is se‐
lected, the initial Forward
Collision Warning is activa‐ted normally. This settingallows for a nominalamount of distance be‐
tween the vehicle or pe‐
destrian ahead before theinitial warning occurs.
• LATE - When this condition is se‐ lected, the initial Forward
Collision Warning is activa‐ted later than normal.
This setting reduces theamount of distance be‐
6-53
6
Driving your vehicle
Page 276 of 523
tween the vehicle or pe‐
destrian ahead before theinitial warning occurs.
Prerequisite for activation
The FCA gets ready to be activated,
when the FCA is selected on the LCD display, and when the following prereq‐
uisites are satisfied.
- The ESC is activated.
- The driving speed is over 10km/h.
(However, FCA is activated within cer‐ tain driving speed.)
- When recognizing the vehicle or the
pedestrian in front. (However, FCA
does not activate according to condi‐
tions in front and vehicle systems,
but it notices only certain warnings.)
WARNING
•The FCA automatically activatesupon placing the ignition switch tothe ON position. The driver can de‐activate the FCA by canceling thesystem setting on the LCD display.
(Continued)
(Continued)
•The FCA automatically deactivatesupon cancelling the ESC, even withthe FCA system ON, and the driverwill not be able to activate the FCAon the LCD display.
•Set or cancel FCA with controllingswitches on steering wheel afterstopping the vehicle in the safeplace for your safety.
FCA warning message and
system control
The FCA produces warning messages
and warning alarms in accordance with the collision risk levels of followings like
vehicle’s sudden braking in front or lack
of vehicle to vehicle distance or collision to pedestrians. Also, it controls the
brakes in accordance with the collision
risk levels.
Forward warning (1st warning)
The warning message appears on the
LCD display with the warning alarms.
Driving your vehicle
6-54
Page 277 of 523
Collision warning (2nd warning)
• The warning message appears on theLCD display with a warning alarm.
• The vehicle will reduce its speed to a certain limit.- The brake activates gradually for vehicles ahead.
- The brake control activates within an arranged limit to ease the im‐
pact from a collision.
Emergency braking (3rd warning)
• The warning message appears on the LCD display with a warning alarm.
• The vehicle will reduce its speed to a certain limit.
- The brake control activates within an arranged limit to ease the im‐
pact from a collision. Maximum
brake control is activated just be‐
fore the collision.
Brake operation
• In an urgent situation, the braking system enters into the ready status
for prompt reaction against the driv‐ er’s depressing the brake pedal. • The FCA provides additional braking
power for optimum braking perform‐
ance, when the driver depresses the
brake pedal.
• The braking control is automatically deactivated, when the driver sharplydepresses the brake pedal, or when
the driver abruptly operates the
steering wheel.
• The braking control is automatically canceled, when risk factors disappear.
CAUTION
The driver should always pay greatcaution to vehicle operation, eventhough there is no warning messageor warning alarm.
WARNING
The FCA cannot avoid all collisions.The FCA might not completely stopthe vehicle before collision, due toambient, weather and road condi‐tions. The driver has the responsibili‐ty to drive safely and control the ve‐hicle.
6-55
6
Driving your vehicle
Page 282 of 523
-When the stopped vehicle in front
gets out of the lane, it may not be
recognized by your FCA. Always pay great attention.
- Recognizing the vehicle
When the vehicle in front has heavy
loading extended rearward, or when
the vehicle in front has higher ground clearance, it may induce a hazardous
situation.
Recognizing pedestrians
- The pedestrian is not fully captured
by the camera sensor, or the pedes‐
trian does not walk in the upright po‐ sition.
- The pedestrian moves very fast.
- The pedestrian abruptly appears in
front.
- The pedestrian wears clothes in the
color similar to the background.
- The outside is too bright or too dark.
- The vehicle drives at night or in the
darkness.
- There is an item similar to a person’s
body structure.
- The pedestrian is small.
- The pedestrian has impaired mobility.
- It is difficult to distinguish the pedes‐
trian from the surroundings.
- The sensor recognition is limited. -
There is a group of pedestrians.
WARNING
•Cancel the FCA in the User Set‐tings on the LCD display, beforetowing another vehicle. While tow‐ing, the brake application may ad‐versely affect your vehicle safety.
•Pay great caution to the vehicle infront, when it has heavy loadingextended rearward, or when it hashigher ground clearance.
•The sensor only detects pedes‐trian, not carts, bicycles, motorcy‐cles, luggage bags, or strollers.
•The FCA does not operate in a cer‐tain situation. Thus, never test-operate the FCA against a personor an object. It may cause a severeinjury or even death.
•When reinstalling the windshield orLane Departure Warning (LDW)camera after replacement or re‐moval, have the vehicle inspectedby a professional workshop. Kiarecommends to visit an authorizedKia dealer/service partner.
Driving your vehicle
6-60
Page 285 of 523
(Continued)
•Always check road conditions be‐cause you may not hear the warn‐ing chime because of audio and ex‐ternal conditions.
To operate the Lane Departure Warning
(LDW) System, press the switch with the ignition in the ON position. The indi‐
cator illuminates white on the cluster.
To cancel the Lane Departure Warning
(LDW) System, press Lane Departure Warning (LDW) System button again.
The indicator on the cluster will go off.
If you select trip display, the Lane De‐
parture Warning (LDW) System mode on the LCD display will appear.
If your vehicle leaves the lane when the
Lane Departure Warning (LDW) System
is operating and vehicle speed exceeds
60 km/h, the warning operates as fol‐
lows:
¥ - F G U M B O F E F Q B S U V S F X B S O J O H
¥ 3 J H I U M B O F E F Q B S U V S F X B S O J O H
1. Visual warning If you leave a lane, the lane you
cross will blink (yellow) and Lane
Departure Warning (LDW) System
indicator will blink green on LCD
during max 3 seconds.
6-63
6
Driving your vehicle
Page 288 of 523
DRIVER ATTENTION WARNING (DAW) SYSTEM (IF EQUIPPED)
The Driver Attention Warning (DAW)
system displays the condition of the
driver's fatigue level and inattentive driving practices.
System setting and activation
System setting
• The Driver Attention Warning system is set to be in the OFF position, when
your vehicle is first delivered to you from the factory.
• To turn ON the Driver Attention Warning system, turn on the engine,
and then select 'User Settings
Driving Assist Driver Attention
Warning Normal/Early' on the LCD
display.
• The driver can select the Driver At‐ tention Warning system mode.- Off: The Driver Attention Warning system is deactivated.
- Normal: The Driver Attention Warning system alerts the driver
of his/her fatigue level or inatten‐
tive driving practices.
- Early: The Driver Attention Warn‐ ing system alerts the driver of
his/her fatigue level or inattentive
driving practices faster than Nor‐mal mode. • The set-up of the Driver Attention
Warning system will be maintained,as selected, when the engine is re‐
started.
Display of the driver's attention
level
0 : # -
4 Z T U F N P G G
0 : # -
" U U F O U J W F E S J W J O H
0 : # -
* O B U U F O U J W F E S J W J O H
• The driver can monitor their driving conditions on the LCD display.
The DAW screen will appear when
you select the ASSIST mode tab (
)
on the LCD display if the system is
activated. (For more information, re‐
fer to L
Page 289 of 523
• When the driver turns on the systemwhile driving, it displays 'Last Break
time' and level.
Take a break
0 : # -
• The "Consider taking a break" mes‐ sage appears on the LCD display and
a warning sounds in order to suggest the driver to take a break, when the
driver's attention level is below 1.
• The Driver Attention Warning system does not suggest the driver to take a
break, when the total driving time is
shorter than 10 minutes.
Resetting the system
• The last break time is set to 00:00 and the driver's attention level is setto 5 (very attentive) when the driver
resets the Driver Attention Warning
system.
• The Driver Attention Warning system resets the last break time to 00:00
and the driver's attention level to 5 in the following situations. - The engine is turned OFF.
- The driver unfastens the seat belt and then opens the driver's door.
- The engine has been idled continu‐ ously over 10 minutes.
• The Driver Attention Warning system operates again, when the driver re‐
starts driving.
System standby
0 : # -
The Driver Attention Warning system
enters the ready status and displays the 'Standby' screen in the following
situations.
- The camera does not detect the
lanes.
- Driving speed remains under 60 km/h
(40 mph) or over 200 km/h
(125 mph).
6-67
6
Driving your vehicle
Page 294 of 523
0 % &
O E T U B H F
The second stage alarm will activate
when: 1. The first stage alert is on
2. The turn signal is on to change a lane
When the second stage alert is activa‐ ted, a warning light will be blinking on
the outside rearview mirror and an
alarm will sound.
If you move the turn signal switch to origin position, the second stage alert
will be deactivated.
- The second stage alarm can be deac‐
tivated. • To activate the alarm:
Go to the User Settings Mode
Sound and select Blind-Spot Collision
Warning Sound on the LCD display.
• To deactivate the alarm : Go to the User Settings Mode
Sound and deselect Blind-Spot Colli‐
sion Warning Sound on the LCD dis‐
play.
CAUTION
The alarm function helps alert thedriver. Deactivate this function onlywhen it is necessary.
Detecting sensor
0 : # %
The sensors are located inside the rear
bumper.
Always keep the rear bumper clean for the system to work properly.
Warning message
The message (L