service KIA STONIC 2018 Repair Manual

• Use your air conditioning sparingly.The air conditioning system is oper‐
ated by engine power so your fuel economy is reduced when you use it.
• Open windows at high speeds can re‐ duce fuel economy.
• Fuel economy is less in crosswinds and headwinds. To help offset some
of this loss, slow down when driving
in these conditions.
Keeping a vehicle in good operating
condition is important both for econo‐
my and safety. Therefore, have the system serviced by a professional
workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
WARNING
nEngine off during motion
Never turn the engine off to coastdown hills or anytime the vehicle isin motion. The power steering andpower brakes will not function prop‐erly without the engine running. In‐stead, keep the engine on and down‐
(Continued)
(Continued)
shift to an appropriate gear for en‐gine braking effect. In addition, turn‐ing off the ignition while drivingcould engage the steering wheel lockresulting in loss of vehicle steeringwhich could cause serious injury ordeath.

6-77
6
Driving your vehicle

To keep locks from freezing
To keep the locks from freezing, squirt
an approved de-icer fluid or glycerine
into the key opening. If a lock is covered with ice, squirt it with an approved de-
icing fluid to remove the ice. If the lock
is frozen internally, you may be able to thaw it out by using a heated key. Han‐
dle the heated key with care to avoid
injury.
Use approved window washer
anti-freeze in system
To keep the water in the window wash‐
er system from freezing, add an ap‐ proved window washer anti-freeze sol‐
ution in accordance with instructions on
the container. Window washer anti- freeze is available from an authorized
Kia dealer/service partner and most au‐
to parts outlets. Do not use engine
coolant or other types of anti-freeze asthese may damage the paint finish.
Don't let your parking brake
freeze
Under some conditions your parking brake can freeze in the engaged posi‐
tion. This is most likely to happen when
there is an accumulation of snow or ice around or near the rear brakes or if the
brakes are wet. If there is a risk the
parking brake may freeze, apply it only temporarily while you put the shift lev‐
er in P (automatic transaxle) or in first
or reverse gear (manual transaxle) and block the rear wheels so the vehicle
cannot roll. Then release the parking
brake.
Don't let ice and snow
accumulate underneath
Under some conditions, snow and ice
can build up under the fenders and in‐ terfere with the steering. When driving
in severe winter conditions where this
may happen, you should periodically check underneath the car to be sure
the movement of the front wheels and
the steering components is not ob‐ structed.
Carry emergency equipment
Depending on the severity of the
weather, you should carry appropriate
emergency equipment. Some of the items you may want to carry include
tire chains, tow straps or chains, flash‐
light, emergency flares, sand, shovel, jumper cables, window scraper, gloves,
ground cloth, coveralls, blanket, etc.

6-85
6
Driving your vehicle

TRAILER TOWING (FOR EUROPE)
If you are considering towing with your
car, you should first check with your
country’s Department of Motor Vehi‐ cles to determine their legal require‐
ments.
Since laws vary the requirements for
towing trailers, cars, or other types of vehicles or apparatus may differ. Kia
recommends to ask an authorized Kia
dealer/service partner.
WARNING
nTowing a trailer
If you don't use the correct equip‐ment and drive improperly, you canlose control when you pull a trailer.For example, if the trailer is tooheavy, the brakes may not work well- or even at all. You and your pas‐sengers could be seriously or fatallyinjured. Pull a trailer only if you havefollowed all the steps in this section.
WARNING
nWeight limits
(Continued)
(Continued)
Before towing, make sure the totaltrailer weight, gross combinationweight, gross vehicle weight, grossaxle weight and trailer tongue loadare all within the limits.
NOTICE
nFor Europe
•The technically permissible maxi‐
mum load on the rear axle(s) may
be exceeded by not more than
15 % and the technically permissi‐
ble maximum laden mass of the
vehicle may be exceeded by not
more than 10 % or 100 kg
(220.4 lbs), whichever value is low‐
er. In this case, do not exceed
100 km/h (62.1 mph) for vehicle of
category M1 or 80 km/h
(49.7 mph) for vehicle of category
N1.
(Continued)
(Continued)
•When towing a trailer, the addi‐
tional load imposed at the trailer
coupling device may cause the
rear tire maximum load ratings to
be exceeded, but not by more
than 15%. In such a case, do not
exceed 100 km/h, and the rear tire
pressure should be at least 20 kPa
(0.2 bar) above the tire pressure(s)
as recommended for normal use
(i.e. without a trailer attached).
CAUTION
Pulling a trailer improperly can dam‐age your vehicle and result in costlyrepairs not covered by your warran‐ty. To pull a trailer correctly, followthe advice in this section.
Your vehicle can tow a trailer. To identi‐
fy what the vehicle trailering capacity is for your vehicle, you should read the in‐
formation in L

Remember that trailering is different
than just driving your vehicle by itself. Trailering means changes in handling,
durability, and fuel economy. Success‐
ful, safe trailering requires correct equipment, and it has to be used prop‐
erly.
This section contains many time-tes‐
ted, important trailering tips and safety
rules. Many of these are important for your safety and that of your passen‐
gers. Please read this section carefully
before you pull a trailer.
Load-pulling components such as the engine, transaxle, wheel assemblies,
and tires are forced to work harder
against the load of the added weight. The engine is required to operate at
relatively higher speeds and under
greater loads. This additional burden generates extra heat. The trailer also
considerably adds wind resistance, in‐
creasing pulling requirements.
0:#%
NOTICE
nLocation of trailer mounting
CUV
After removing rear bumper and
back beam, hitch equipment can be
installed. The rear bumper should be
reinstalled after completion of hitch
equipment installation.
Hitches
It's important to have the correct hitch
equipment. Crosswinds, large trucks going by, and rough roads are a few
reasons why you’ll need the right hitch.
Here are some rules to follow: • Do you have to make any holes in the
body of your vehicle when you installa trailer hitch? If you do, then be sure
to seal the holes later when you re‐
move the hitch.
If you don’t seal them, deadly carbon
monoxide (CO) from your exhaust can get into your vehicle, as well as
dirt and water.
• The bumpers on your vehicle are not intended for hitches. Do not attach
rental hitches or other bumper-type
hitches. Use only a frame-mounted hitch that does not attach to the
bumper.
• Kia trailer hitch accessary is available at an authorized Kia dealer/service
partner.
Safety chains
You should always attach chains be‐
tween your vehicle and your trailer. Cross the safety chains under the
tongue of the trailer so that the tongue
will not drop to the road if it becomes separated from the hitch.

6-87
6
Driving your vehicle

Making turns
When you’re turning with a trailer,
make wider turns than normal. Do this so your trailer won’t strike soft should‐
ers, curbs, road signs, trees, or other
objects. Avoid jerky or sudden maneu‐ vers. Signal well in advance.
Turn signals when towing a trailer
When you tow a trailer, your vehicle
has to have a different turn signal flasher and extra wiring. The green ar‐
rows on your instrument panel will
flash whenever you signal a turn or lane change. Properly connected, the
trailer lights will also flash to alert oth‐
er drivers you’re about to turn, change lanes, or stop.
When towing a trailer, the green ar‐
rows on your instrument panel will
flash for turns even if the bulbs on the trailer are burned out. Thus, you may
think drivers behind you are seeing
your signals when, in fact, they are not. It’s important to check occasionally to
be sure the trailer bulbs are still work‐
ing. You must also check the lights ev‐ ery time you disconnect and then re‐
connect the wires.
Do not connect a trailer lighting system
directly to your vehicle’s lighting sys‐ tem. Use only an approved trailer wir‐
ing harness. Have yourself assisted by a professio‐
nal workshop in installing the wiring harness.
Kia recommends to visit an authorized
Kia dealer/service partner.
WARNING
Failure to use an approved trailerwiring harness could result in dam‐age to the vehicle electrical systemand/or personal injury.
Driving on grades
Reduce the speed and shift to a lower
gear before you start down a long or steep downgrade. If you don’t shift
down, you might have to use your
brakes so much that they would get hot and no longer operate efficiently.
On a long uphill grade, shift down and
reduce your speed to around 70 km/h
(45 mph) to reduce the possibility of engine and transaxle overheating.
If your trailer weighs more than the
maximum trailer weight without trailer
brakes and you have an automatic transaxle, you should drive in D (Drive)
when towing a trailer. Operating your vehicle in D (Drive)
when towing a trailer will minimize heat build up and extend the life of
your transaxle.
CAUTION
•When towing a trailer on steepgrades (in excess of 6%) pay closeattention to the engine coolanttemperature gauge to ensure theengine does not overheat. If theneedle of the coolant temperaturegauge moves across the dial to‐wards L

Maintenance when trailer
towing
Your vehicle will need service more of‐
ten when you regularly pull a trailer.
Important items to pay particular at‐ tention to include engine oil, automatic
transaxle fluid, axle lubricant and cool‐
ing system fluid. Brake condition is an‐ other important item to frequently
check. Each item is covered in this man‐
ual, and the Index will help you find them quickly. If you’re trailering, it’s a
good idea to review these sections be‐
fore you start your trip.
Don’t forget to also maintain your trail‐ er and hitch. Follow the maintenance
schedule that accompanied your trailer
and check it periodically. Preferably, conduct the check at the start of each
day’s driving. Most importantly, all
hitch nuts and bolts should be tight.
CAUTION
•Due to higher load during trailerusage, overheating might occur inhot days or during uphill driving. Ifthe coolant gauge indicates over‐heating, switch off the A/C andstop the vehicle in a safe area tocool down the engine.
•When towing, check the transaxlefluid more frequently.
•If your vehicle is not equipped withan air conditioner, you should in‐stall a condenser fan to improveengine performance when towinga trailer.
If you do decide to pull a trailer
Here are some important points if you
decide to pull a trailer:
• Consider using a sway control. You can ask a hitch dealer about swaycontrol. • Do not do any towing with your car
during its first 2,000 km (1,200 miles)
in order to allow the engine to prop‐
erly break in. Failure to heed this cau‐
tion may result in serious engine or transaxle damage.
• When towing a trailer, Kia recom‐ mends that you consult an author‐
ized Kia dealer/service partner on ad‐
ditional requirements such as a tow‐
ing kit, etc.
• Always drive your vehicle at a moder‐ ate speed (less than 100 km/h
(60 mph)).
• On a long uphill grade, do not exceed 70 km/h (45 mph) or the posted tow‐
ing speed limit, whichever is lower.
• The chart contains important consid‐ erations that have to do with weight:
For Europe
Item1.0L T-GDI1.2L MPI1.4L MPI1.6L Diesel
6M/T5M/T6M/T6M/T
Maximum trailerweight Without brake System 450 (992) 450 (992) 450 (992) 450 (992)


6-91
6
Driving your vehicle

Road warning............................................................................. 7-02Hazard warning flasher........................................................7-02
In case of an emergency while driving.................................. 7-03 If the engine stalls at a crossroad or crossing................. 7-03
If you have a flat tire while driving.................................... 7-03
If the engine stalls while driving......................................... 7-03
If the engine will not start....................................................... 7-04 If the engine doesn't turn over or turns over slowly...... 7-04
If the engine turns over normally but does not start.... 7-04
Emergency starting.................................................................. 7-05 Jump starting.........................................................................7-05
Push-starting........................................................................ 7-06
If the engine overheats............................................................ 7-07
Tire pressure monitoring system (TPMS) ........................... 7-08 System Overview.................................................................. 7-08
TPMS Setting......................................................................... 7-08
Indication of Low Tire Pressure.......................................... 7-09
Tire Pressure Monitoring System malfunction................7-10
Reference : Indicator Light Status..................................... 7-11
If You Have A Flat Tire (With Spare Tire).............................. 7-12 Jack and tools........................................................................ 7-12
Removing and storing the spare tire................................. 7-12
Changing tires........................................................................ 7-13
Jack label.................................................................................7-18
EC Declaration of Conformity for Jack.............................. 7-19
If you have a flat tire (with tire mobility kit)........................7-20 Introduction............................................................................7-21
Components of the Tire Mobility Kit (TMK)......................7-22
Using the Tire Mobility Kit................................................... 7-23
Distributing the sealant....................................................... 7-24 Checking the tire inflation pressure...................................7-24
Notes on the safe use of the Tire Mobility Kit................ 7-25
Technical data........................................................................ 7-25
Towing......................................................................................... 7-26 Towing service....................................................................... 7-26
Removable towing hook ..................................................... 7-27
Emergency towing................................................................ 7-27
Emergency commodity ........................................................... 7-30 Fire extinguisher................................................................... 7-30
First aid kit............................................................................. 7-30
Triangle reflector.................................................................. 7-30
Tire pressure gauge .............................................................7-30
What to do in an emergency

7

EMERGENCY STARTING
Connect cables in numerical order and
disconnect in reverse order.
Jump starting
Jump starting can be dangerous if done
incorrectly. Therefore, to avoid harm to yourself or damage to your vehicle or
battery, follow the jump starting pro‐
cedures. If in doubt, we strongly rec‐ ommend that you have a competent
technician or towing service jump start
your vehicle.
CAUTION
Use only a 12-volt jumper system.You can damage a 12-volt startingmotor, ignition system, and otherelectrical parts beyond repair by useof a 24- volt power supply (eithertwo 12-volt batteries in series or a24-volt motor generator set).
WARNING
nBattery
Never attempt to check the electro‐lyte level of the battery as this maycause the battery to rupture or ex‐plode causing serious injury.
WARNING
nBattery
(Continued)
(Continued)
•Keep all flames or sparks awayfrom the battery. The batteryproduces hydrogen gas which mayexplode if exposed to flame orsparks.If these instructions are not fol‐lowed exactly, serious personal in‐jury and damage to the vehiclemay occur! If you are not sure howto follow this procedure, seekqualified assistance. Automobilebatteries contain sulfuric acid. Thisis poisonous and highly corrosive.When jump starting, wear protec‐tive glasses and be careful not toget acid on yourself, your clothingor on the vehicle.
•Do not attempt to jump start thevehicle if the discharged battery isfrozen or if the electrolyte level islow; the battery may rupture orexplode.
•Do not allow the (+) and (-) jumpercables to touch. It may causesparks.
•The battery may rupture or ex‐plode when you jump start with alow or frozen battery.

7-05
7
What to do in an emergency

Jump starting procedure
1. Make sure the booster battery is12-volt and that its negative termi‐ nal is grounded.
2. If the booster battery is in another vehicle, do not allow the vehicles to
come in contact.
3. Turn off all unnecessary electrical loads.
4. Connect the jumper cables in the exact sequence shown in the illus‐
tration. First connect one end of a
jumper cable to the positive termi‐
nal of the discharged battery (1),
then connect the other end to the
positive terminal on the booster
battery (2).
Proceed to connect one end of the other jumper cable to the negative
terminal of the booster battery (3),
then the other end to a solid, sta‐
tionary, metallic point (for example,
the engine lifting bracket) away
from the battery (4). Do not con‐
nect it to or near any part that
moves when the engine is cranked.
Do not allow the jumper cables to
contact anything except the correct
battery terminals or the correct
ground. Do not lean over the bat‐ tery when making connections.CAUTION
nBattery cables
Do not connect the jumper cablefrom the negative terminal of thebooster battery to the negative ter‐minal of the discharged battery. Thiscan cause the discharged battery tooverheat and crack, releasing bat‐tery acid.Make sure to connect one end of thejumper cable to the negative termi‐nal of the booster battery, and theother end to a metallic point, faraway from the battery.
5. Start the engine of the vehicle with the booster battery and let it run
at 2,000 rpm, then start the engine
of the vehicle with the discharged
battery.
If the cause of your battery discharging
is not apparent, have the systemchecked by a professional workshop.Kia recommends to visit an authorized Kia dealer/service partner.
Push-starting
Your manual transaxle-equipped vehi‐
cle should not be push-started because it might damage the emission control
system.
Vehicles equipped with automatic
transaxle cannot be push-started.
Follow the directions in this section for L

IF THE ENGINE OVERHEATS
If your temperature gauge indicates
overheating, you will experience a loss of power, or hear loud pinging or knock‐
ing, the engine is probably too hot. If
this happens, you should: 1. Pull off the road and stop as soon as it is safe to do so.
2. Place the shift lever in P (automatic transaxle) or neutral (manual
transaxle) and set the parking
brake. If the air conditioning is on, turn it off.
3. If engine coolant is running out un‐ der the vehicle or steam is coming
out from the hood, stop the engine.
Do not open the hood until the
coolant has stopped running or the
steaming has stopped. If there is no
visible loss of engine coolant and no
steam, leave the engine running
and check to be sure the engine
cooling fan is operating. If the fan is
not running, turn the engine off.
4. Check to see if the water pump drive belt is missing. If it is not
missing, check to see that it is
tight.
If the drive belt seems to be satis‐
factory, check for coolant leaking
from the radiator, hoses or under
the vehicle. (If the air conditioning had been in use, it is normal for
cold water to be draining from it
when you stop).
WARNING
While the engine is running, keephair, hands and clothing away frommoving parts such as the fan anddrive belts to prevent injury.
5. If the water pump drive belt is bro‐ ken or engine coolant is leaking out,
stop the engine immediately and
call a professional workshop. Kia
recommends to call an authorized
Kia dealer/service partner.
WARNING
Do not remove the radiator capwhen the engine is hot. This can al‐low coolant to blow out of the open‐ing and cause serious burns.
6. If you cannot find the cause of the overheating, wait until the engine
temperature has returned to nor‐
mal. Then, if coolant has been lost,
carefully add coolant to the reser‐
voir to bring the fluid level in the
reservoir up to the halfway mark.
7. Proceed with caution, keeping alert for further signs of overheating. Ifoverheating happens again, call a
professional workshop. Kia recom‐
mends to call an authorized Kia
dealer/service partner.
CAUTION
•Serious loss of coolant indicatesthere is a leak in the cooling sys‐tem. In this case, have the sys‐tem checked by a professionalworkshop. Kia recommends tovisit an authorized Kia dealer/service partner.
•When the engine overheats fromlow engine coolant, suddenlyadding engine coolant may causecracks in the engine. To preventdamage, add engine coolantslowly in small quantities.

7-07
7
What to do in an emergency