engine KIA STONIC 2018 Manual Online

ISG (IDLE STOP AND GO) SYSTEM (IF EQUIPPED)
Your vehicle may be equipped with the
ISG system, which reduces fuel con‐ sumption by automatically shutting
down the engine, when the vehicle is at
a standstill. (For example : red light, stop sign and traffic jam)
The engine starts automatically as
soon as the starting conditions are
met.
The ISG system is ON whenever the en‐ gine is running.
NOTICE
When the engine automatically
starts by the ISG system, some
warning lights (ABS, ESC, ESC OFF,
EPS or Parking brake warning light)
may turn on for a few seconds.
This happens because of low battery
voltage. It does not mean the sys‐
tem is malfunctioning.
Auto stop
To stop the engine in idle stop
mode
• Manual transaxle 1. Decrease the vehicle speed to less than 5 km/h.
2. Shift into N (Neutral) position.
3. Release the clutch pedal.
• Automatic transaxle 1. Decrease the vehicle speed to less than 5 km/h.
2. Press the brake pedal. The engine will stop and the green AU‐
TO STOP indicator (
) on the instru‐
ment cluster will illuminate. If your ve‐ hicle is equipped with a supervision
cluster, the notice will illuminate on the
LCD display.
Driving your vehicle
6-16

NOTICE
•You must reach a speed of at least
10 km/h since last idle stop.
•If you unfasten the seat belt or
open the driver’s door (engine
hood) in auto stop mode, the light
on the ISG OFF button will illumi‐
nate and ISG system is deactiva‐
ted. If your vehicle is equipped
with a supervision cluster, the no‐
tice will illuminate on the LCD dis‐
play. Turn the ignition switch to
the START position to start the
engine manually.
Auto start
To restart the engine from idle stop
mode
• Manual transaxle- Press the clutch pedal when theshift lever is in the N (Neutral) po‐
sition.
• Automatic transaxle - Release the brake pedal.
The engine will start and the green AU‐
TO STOP indicator (
) on the instru‐
ment cluster will go out. If your vehicle is equipped with a supervision cluster,
the notice will illuminate on the LCD
display.

6-17
6
Driving your vehicle

The engine will also restart
automatically without the driver's
any actions if the following occurs:
-The fan speed of manual climate con‐
trol system is set above the 3rd posi‐
tion when the air conditioning is on.
- The fan speed of automatic climate
control system is set above the 6th
position when the air conditioning is on.
- When a certain amount of time has
passed with the climate control sys‐
tem on.
- When the defroster is on.
- The brake vacuum pressure is low.
- The battery charging status is low.
- The vehicle speed exceeds 5 km/h.
The green AUTO STOP indicator (
) on
the instrument cluster will blink for 5
seconds.
Condition of ISG system
operation
The ISG system will operate under
the following condition:
- The driver’s seat belt is fastened. -
The driver’s door and hood are closed.
- The brake vacuum pressure is ade‐
quate.
- The battery is sufficiently charged.
- The outside temperature is more
than -2°C (28.4°F).
- The outside temperature is under
32°C (89.6°F).
- The engine coolant temperature is
not too low.
NOTICE
•If the ISG system does not meet
that operation condition, the ISG
system is deactivated. The light on
the ISG OFF button will illuminate.
•If the light comes on continuously,
please check the operation condi‐
tion.
ISG system deactivation
• If you want to deactivate the ISG system, press the ISG OFF button.
The light on the ISG OFF button will il‐ luminate.
Driving your vehicle
6-18

• If you press the ISG OFF button again,the system will be activated and the
light on the ISG OFF button will turn off.
ISG system malfunction
The system may not operate
when:
- The ISG related sensors or system
error occurs.
The yellow AUTO STOP indicator (
)
on the instrument cluster will stay on
after blinking for 5 seconds and the light on the ISG OFF button will illumi‐
nate.
NOTICE
•If the ISG OFF button light is not
turned off by pressing the ISG OFF
button again or if the ISG system
continuously does not work cor‐
rectly, have your vehicle inspected
by a professional workshop as
soon as possible.
Kia recommends to contact an au‐
thorized Kia dealer/service part‐
ner.
•When the ISG OFF button light
comes on, it may stop illuminating
after driving your vehicle at ap‐
proximately 80 km/h for a maxi‐
mum of two hours and setting the
fan speed control knob below the
2nd position. If the ISG OFF button
light continues to be illuminated in
spite of the procedure, have your
vehicle inspected by a professional
workshop as soon as possible. Kia
recommends to contact an au‐
thorized Kia dealer/service part‐
ner.
NOTICE
If you want to use the ISG function,
the battery sensor needs to be cali‐
brated for approximately 4 hours
with the ignition off and then, turn
the engine on and off 2 or 3 times.
WARNING
When the engine is in Idle Stopmode, it's possible to restart the en‐gine without the driver taking anyaction.Before leaving the car or doing any‐thing in the engine room area, stopthe engine by turning the ignitionswitch to the LOCK(OFF) position orremoving the ignition key.

6-19
6
Driving your vehicle

This shift pattern is imprinted on the
shift knob. The transaxle is fully synchronized in all forward gears so
shifting to either a higher or a lower
gear is easily accomplished.
Depress the clutch pedal down fully while shifting, then release it slowly.
If your vehicle is equipped with an igni‐
tion lock switch, the engine will not
start when starting the engine without depressing the clutch pedal. (if equip‐
ped)
The shift lever must be returned to the
neutral position before shifting into R (Reverse).
Push the button located immediately
below the shift knob and pull the gear‐
shift lever to the left sufficiently, and then shift into reverse (R) gear position.
Make sure the vehicle is completely
stopped before shifting into R (Re‐verse).
Never operate the engine with thetachometer (rpm) in the red zone.
CAUTION
•When downshifting from fifth gearto fourth gear, caution should betaken not to inadvertently pressthe shift lever sideways in such amanner that the second gear isengaged. Such a drastic downshiftmay cause the engine speed to in‐crease to the point that the tach‐ometer will enter the red-zone.Such over-revving of the engineand transaxle may possibly causeengine damage.
•Do not downshift more than 2gears or downshift the gear whenthe engine is running at high speed(5,000 RPM or higher). Such adownshifting may damage the en‐gine, clutch and the transaxle.
• During cold weather, shifting may be difficult until the transaxle lubricant
is warmed up. This is normal and not harmful to the transaxle. • If you've come to a complete stop
and it's hard to shift into 1st or R(Re‐
verse), leave the shift lever at N(Neu‐
tral) position and release the clutch.
Press the clutch pedal back down, and then shift into 1st or R(Reverse)
gear position.
CAUTION
•To avoid premature clutch wearand damage, do not drive withyour foot resting on the clutchpedal. Also, don’t use the clutch tohold the vehicle stopped on an up‐hill grade, while waiting for a traf‐fic light, etc.
•Do not use the shift lever as ahandrest during driving, as this canresult in premature wear of thetransaxle shift forks.
•To prevent possible damage to theclutch system, do not start withthe 2nd (second) gear engaged ex‐cept when you start on a slipperyroad.

6-21
6
Driving your vehicle

WARNING
•Before leaving the driver’s seat, al‐ways set the parking brake fullyand shut the engine off. Thenmake sure the transaxle is shiftedinto 1st gear when the vehicle isparked on a level or uphill grade,and shifted into R (Reverse) on adownhill grade. Unexpected andsudden vehicle movement can oc‐cur if these precautions are notfollowed in the order identified.
•Do not use the engine brake (shift‐ing from a high gear to lower gear)rapidly on slippery roads.The vehicle may slip causing an ac‐cident.
Using the clutch
The clutch should be pressed all theway to the floor before shifting, then
released slowly. The clutch pedal should
always be fully released while driving. Do not rest your foot on the clutch
pedal while driving. This can cause un‐
necessary wear. Do not partially en‐ gage the clutch to hold the vehicle on
an incline. This causes unnecessary
wear. Use the foot brake or parking brake to hold the vehicle on an incline.
Do not operate the clutch pedal rapidly
and repeatedly.
CAUTION
When operating the clutch pedal,press the clutch pedal down fully. Ifyou don’t press the clutch pedalfully, the clutch may be damaged ornoise may occur.
Downshifting
When you must slow down in heavy
traffic or while driving up steep hills, downshift before the engine starts to
labor. Downshifting reduces the chance
of stalling and gives better acceleration when you again need to increase your
speed. When the vehicle is traveling
down steep hills, downshifting helps maintain safe speed and prolongs brake life.
Good driving practices
• Never take the vehicle out of gear and coast down a hill. This is ex‐
tremely hazardous. Always leave the vehicle in gear.
• Don't "ride" the brakes. This can cause them to overheat and malfunc‐
tion. Instead, when you are driving
down a long hill, shift to a lower gear.
When you do this, engine braking will help slow down the vehicle.
• Slow down before shifting to a lower gear. This will help avoid over-revving
the engine, which can cause damage.
• Slow down when you encounter cross winds. This gives you much better
control of your vehicle.
Driving your vehicle
6-22

(Continued)
•Always check the surroundingareas near your vehicle for people,especially children, before shiftinga car into D (Drive) or R (Reverse).
•Before leaving the driver’s seat, al‐ways make sure the shift lever isin the P (Park) position; then setthe parking brake fully and shutthe engine off. Unexpected andsudden vehicle movement can oc‐cur if these precautions are notfollowed in the order identified.
•Do not use the engine brake (shift‐ing from a high gear to lower gear)rapidly on slippery roads.The vehicle may slip causing an ac‐cident.
CAUTION
•To avoid damage to your trans‐axle, do not accelerate the enginein R (Reverse) or any forward gearposition with the brakes on.
(Continued)
(Continued)
•When stopped on an incline, do nothold the vehicle stationary withengine power.Use the service brake or the park‐ing brake.
•Do not shift from N (Neutral) or P(Park) into D (Drive), or R (Reverse)when the engine is above idlespeed.
Transaxle ranges
The indicator in the instrument cluster
displays the shift lever position when the ignition switch is in the ON position.
P (Park)
Always come to a complete stop before
shifting into P (Park). This position
locks the transaxle and prevents the drive wheels from rotating.
WARNING
•Shifting into P (Park) while the ve‐hicle is in motion will cause thedrive wheels to lock which willcause you to lose control of thevehicle.
•Do not use the P (Park) position inplace of the parking brake. Alwaysmake sure the shift lever is latch‐ed in the P (Park) position and setthe parking brake fully.
•Never leave a child unattended in avehicle.
CAUTION
The transaxle may be damaged ifyou shift into P (Park) while the ve‐hicle is in motion.
R (Reverse)
Use this position to drive the vehicle
backward.

6-25
6
Driving your vehicle

Sports mode (if equipped)

61

%08/

4QPSUT

NPEF
Whether the vehicle is stationary or in
motion, sports mode is selected by pushing the shift lever from the D
(Drive) position into the manual gate.
To return to D (Drive) range operation, push the shift lever back into the main
gate.
In sports mode, moving the shift lever
backwards and forwards will allow you to make gearshifts rapidly. In contrast
to a manual transaxle, the sports mode
allows gearshifts with the accelerator
pedal depressed.
Using the shift lever
Up (+) : Push the lever forward once to shift up one
gear.
Down (-) : Pull the lever backwards once to shift down one
gear.
NOTICE
•In sports mode, the driver must
execute upshifts in accordance
with road conditions, taking care
to keep the engine speed below
the red zone.
•In sports mode, only the 4 or 6
forward gears can be selected. To
reverse or park the vehicle, move
the shift lever to the R (Reverse)
or P (Park) position as required.
•In sports mode, downshifts are
made automatically when the ve‐
hicle slows down. When the vehicle
stops, 1st gear is automatically
selected.
(Continued)
(Continued)
•In sports mode, when the engine
rpm approaches the red zone shift
points are varied to upshift auto‐
matically.
•To maintain the required levels of
vehicle performance and safety,
the system may not execute cer‐
tain gearshifts when the shift lev‐
er is operated.
•When driving on a slippery road,
push the shift lever forward into
the +(up) position. This causes the
transmission to shift into the 2nd
gear which is better for smooth
driving on a slippery road. Push
the shift lever to the -(down) side
to shift back to the 1st gear.
Shift lock system (if equipped)
For your safety, the automatic trans‐
axle has a shift lock system which pre‐ vents shifting the transaxle from P
(Park) into R (Reverse) unless the brake
pedal is depressed.
To shift the transaxle from P (Park) in‐ to R (Reverse): 1. Depress and hold the brake pedal.

6-27
6
Driving your vehicle

2. Move the shift lever.
If the brake pedal is repeatedly de‐
pressed and released with the shift lev‐ er in the P (Park) position, a chattering
noise near the shift lever may be heard.
This is a normal condition.
WARNING
Always fully depress the brake pedalbefore and while shifting out of theP (Park) position into another posi‐tion to avoid inadvertent motion ofthe vehicle which could injure per‐sons in or around the car.
Good driving practices
• Never move the shift lever from P (Park) or N (Neutral) to any other po‐
sition with the accelerator pedal de‐ pressed.
• Never move the shift lever into P (Park) when the vehicle is in motion.
• Be sure the car is completely stopped before you attempt to shift into R
(Reverse) or D (Drive). • Never take the car out of gear and
coast down a hill. This may be ex‐tremely hazardous. Always leave the
car in gear when moving.
• Do not "ride" the brakes. This can cause them to overheat and malfunc‐
tion. Instead, when you are driving
down a long hill, slow down and shift to a lower gear. When you do this,
engine braking will help slow the car.
• Slow down before shifting to a lower gear. Otherwise, the lower gear may
not be engaged.
• Always use the parking brake. Do not depend on placing the transaxle in P
(Park) to keep the car from moving.
• Exercise extreme caution when driv‐ ing on a slippery surface. Be especial‐
ly careful when braking, accelerating
or shifting gears. On a slippery sur‐ face, an abrupt change in vehicle
speed can cause the drive wheels to
lose traction and the vehicle to go out
of control.
• Optimum vehicle performance and economy is obtained by smoothly de‐
pressing and releasing the accelera‐
tor pedal.
WARNING
•Always buckle-up! In a collision, anunbelted occupant is significantlymore likely to be seriously injuredor killed than a properly belted oc‐cupant.
•Avoid high speeds when corneringor turning.
•Do not make quick steering wheelmovements, such as sharp lanechanges or fast, sharp turns.
•The risk of rollover is greatly in‐creased if you lose control of yourvehicle at highway speeds.
•Loss of control often occurs if twoor more wheels drop off the road‐way and the driver over-steers toreenter the roadway.
•In the event your vehicle leavesthe roadway, do not steer sharply.Instead, slow down before pullingback into the travel lanes.
•Never exceed posted speed limits.
Driving your vehicle
6-28

BRAKE SYSTEM
Power brakes
Your vehicle has power-assisted brakesthat adjust automatically through nor‐
mal usage.
In the event that the power-assisted
brakes lose power because of a stalled engine or some other reason, you can
still stop your vehicle by applying
greater force to the brake pedal than you normally would. The stopping dis‐
tance, however, will be longer.
When the engine is not running, the re‐
serve brake power is partially depleted each time the brake pedal is applied. Do
not pump the brake pedal when the
power assist has been interrupted.
Pump the brake pedal only when nec‐ essary to maintain steering control on
slippery surfaces.
WARNING
nBrakes
(Continued)
(Continued)
•Do not drive with your foot restingon the brake pedal. This will createabnormal high brake tempera‐tures, excessive brake lining andpad wear, and increased stoppingdistances.
•When descending a long or steephill, shift to a lower gear and avoidcontinuous application of thebrakes. Continuous brake applica‐tion will cause the brakes to over‐heat and could result in a tempo‐rary loss of braking performance.
•Wet brakes may impair the vehi‐cle’s ability to safely slow down;the vehicle may also pull to oneside when the brakes are applied.Applying the brakes lightly will in‐dicate whether they have been af‐fected in this way. Always testyour brakes in this fashion afterdriving through deep water. To drythe brakes, apply them lightlywhile maintaining a safe forwardspeed until brake performance re‐turns to normal.
(Continued)
(Continued)
•Always, confirm the position ofthe brake and accelerator pedalbefore driving. If you don't checkthe position of the accelerator andbrake pedal before driving, youmay depress the accelerator in‐stead of the brake pedal. It maycause a serious accident.
In the event of brake failure
If service brakes fail to operate while
the vehicle is in motion, you can make an emergency stop with the parking
brake. The stopping distance, however,
will be much greater than normal.
WARNING
nParking brake
Applying the parking brake while thevehicle is moving at normal speedscan cause a sudden loss of control ofthe vehicle. If you must use theparking brake to stop the vehicle,use great caution in applying thebrake.
Driving your vehicle
6-30