ignition KIA TELLURIDE 2022 Features and Functions Guide
[x] Cancel search | Manufacturer: KIA, Model Year: 2022, Model line: TELLURIDE, Model: KIA TELLURIDE 2022Pages: 70, PDF Size: 5.27 MB
Page 34 of 70
AUTO Light – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically depending on the amount of light outside the vehicle .
Daytime Running Lights (DRL) – DRL may help others to see the front of your vehicle during the day . The lights will turn on automatically when the ignition or Engine Start/Stop button is ON and the headlight switch is in the AUTO position, unless one of the following occurs:
• Headlights are on
• Parking brake is applied
• Engine is turned off
• Switch is in the DRL OFF position
Headlight / High Beam Lever Operation
•Rotate lever switch to change the headlight function:
•
Press lever away from you to turn high beam headlights ON
•
Pull lever to flash headlights/high beams or to turn off the high beams
High Beam Assist (HBA)* – High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from other vehicles and road conditions .
To enable HBA , toggle the light switch to the AUTO Light position and turn on the high beams by pushing the lever away from you . The High Beam Assist indicator will illuminate .
*IF EQUIPPED32TELLURIDE FEATURES & FUNCTIONS GUIDE
REMINDERS:
•
High Beam Assist does not operate below cer tain speeds, or in some lighting and driving conditions . Please be aware of your surroundings and exercise proper road etiquet te when operating a vehicle using the high beams
•HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously . If the lever is pulled toward you while HBA is operational, HBA will turn off
•If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
•
When the HBA indicator illuminates on the instrument cluster, the HBA is not working properly . See an authorized Kia dealer for ser vice
OFF
OFF
) F B E M J H I U Q P T J U J P O
1 B S L J O H - J H I U \
Q P T J U J P O
AUTOAuto Light /DRL/ High Beam Assist*
OFFOFF position
Headlights & High Beams
See section 4 in the Owner’s Manual for more information .
A
To operate Turn Signals: Move lever up/down for right/left turn signal .
One-touch lane change signal is activated by briefly pressing the turn signal lever slightly for less than 1 second and then releasing . The lane change signal will blink 3 times .
To change how many times the lane change signal blinks (3/5/7), go to User Settings in the LCD instrument cluster modes .
To operate Fog Lights: Press switch A up/down to turn on/off the Fog Lights .
Turn Signals & Fog Lights*
REMINDER: Headlights must be on for fog light operation .
See section 4 in the Owner’s Manual for more information . For illustrative purposes only . Your actual display, buttons and/or features may vary .
STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS
Page 35 of 70
See section 4 in the Owner’s Manual for more information .
STEERING WHEEL
CONTROLS
STEERING WHEEL CONTROLS
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED33
Headlight position
Parking Light position
AUTOAuto Light /DRL/ High Beam Assist*
OFFOFF position
To operate front wipers & washers:
•Move lever up/down to change wiper modes
MIST: Single wipe LO: Slow wipeOFF: Wiper off HI: Fast wipeINT*/AUTO*: Intermittent*/Auto Rain Sensing*
•Pull to spray and wipe
To operate rear wipers & washers:
•Rotate Rear Wiper switch to change Wiper modes
•Push lever to spray and wipe
Auto Rain Sensing (Auto Control)*
The rain sensor located on the upper end of the windshield glass is designed to sense the amount of rainfall and control the wiping cycle for the proper interval . The more it rains, the faster the wiper operates . When the rain stops, the wiper stops .
To turn ON the auto rain sensing wipers, move lever up/down to AUTO . To adjust the auto rain sensing wiper speed setting, move the speed control switch A up/down .
Auto Rear Wiper* – The feature can be enabled in the User Settings on the Instrument Cluster . When the lever is in the AUTO position, the gear shift is moved into Reverse (R), Auto Rear Wiper activates and will wipe the rear windshield .
Front & Rear Windshield Wipers & Washers
HI
LO
OFF
"
#
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wipers and Wiper Stalk Video
QR CODE
CImage for illustrative purposes only . See section 7 in the Owner’s Manual for more information .
To lift the windshield wipers to clean the windshield, inspect or replace wiper blades or raise the wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the middle of the windshield (service position) C .
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch up to the MIST position B and hold the switch for more than two seconds until the wiper blade is in the fully up position .
To return wipers to the normal position, turn the ignition ON, then activate MIST .
Lifting Wipers/Winter Mode (Wiper Service Mode)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wiper Service ModeVideo
QR CODE
MIST: Single wipe
OFF: Wiper off
LO: Slow wipe
HI: Fast wipe
INT*/AUTO: Intermittent*/Auto/Rain Sensing*
•When the Engine Star t/Stop but ton is in the ON position and the wiper switch is in AUTO mode, the wiper will automatically operate once to per form a self-check of the system
•Set the wiper to the OFF position when the wiper is not in use
•Moving lever to HI increases intermit tent wipe frequency and wipe speed . Moving lever to LO decreases frequency of wipes
•Pressing but ton A up increases Intermit tent wipe frequency and wipe speed . Pressing but ton A down decreases frequency of wipes
•On Rear Wipers, intermit tent wipe function is not adjustable
QUICK TIPS
Page 42 of 70
AUDIO SYSTEMS
*IF EQUIPPED40TELLURIDE FEATURES & FUNCTIONS GUIDE
AUDIOSYSTEMS
Kia Access with UVO link App Download
Kia Access with UVO link App Features Guide
Go to an app marketplace to download the new Kia Access with UVO link App . Once you download, make sure you register your vehicle and start an account (refer to UVO link Activation page) . Get to know
your new Kia and the available convenient features on the app .
The Kia Access with UVO link App Features Guide is a step-by-step guide helping you utilize the app to its full potential by detailing how to set up and use each feature and adjust various settings . Below are some of the topics included:
•Remote Commands
•Set Climate
•Schedule Service
Download the Kia Access with UVO link App by clicking this dynamic QR code . Some phone’s operating systems may need to be updated to scan dynamic QR codes .
Kia Access with UVO link App Features Guide. Click this dynamic QR code to access the guide . Some phone’s operating systems may need to be updated to scan dynamic QR codes .
2020 SOULMILEAGE722 mi.
355 miEst. RangeDOOR LOCKSREMOTE STARTFind My Car
Kia App Screen for illustrative purposes only . Actual App screen and functionality may vary .
UVO link is currently unavailable for model year 2022 vehicles sold or purchased in Massachusetts . See UVO Terms of Service at owners .kia .com for more information .
For further UVO link operations, refer to the Car Infotainment System Quick Reference Guide .
UVO link is currently unavailable for model year 2022 vehicles sold or purchased in Massachusetts . See UVO Terms of Service at owners .kia .com for more information .
QR CODES
•
To download map updates for the navigation system, go to update .kia .com . Check for updates that are generally available t wice a year
•The smar tphone and vehicle need to be connected to a cellular net work with good wireless signal strength in order to use UVO . If these conditions are not met, remote command may not execute or takes a long time . It will also effect voice commands
•
To use Remote Star t or Remote Star t with Climate Control feature, all doors, hood and trunk/liftgate must be closed and locked
•
When Remote Star t is activated, if the driver does not enter the vehicle within 10 minutes, the Remote Star t will turn the engine off
•When using Remote Star t with Climate Control, turn on for at least a few minutes before get ting into the vehicle, allowing the vehicle interior to reach your desired temperature
•
The quickest way to obtain accurate vehicle status through the app is by pressing the refresh but ton on the app or refreshing the web page when using the customer web por tal
•
In order to preser ve the vehicle bat ter y, UVO will not turn on seven days after the last ignition was on . You will need to restar t the vehicle with a key fob in order to use UVO again
QUICK TIPS
Page 44 of 70
CENTER PANEL
CENTER PANEL
*IF EQUIPPED42TELLURIDE FEATURES & FUNCTIONS GUIDE
Press the SETUP key on the audio head unit, then press the GENER AL button then date/time button to enter the clock settings . Then use the onscreen buttons to navigate through setup and return to exit .
REMINDERS:
•
Daylight Saving must be enabled or disabled in the Clock Set tings screen
•To access manual date and time set ting, turn GPS Time OFF in the Clock Set tings (UVO link with Navigation*)
Refer to the Car Infotainment System Quick Reference Guide for more information .
Clock
The AC Inverter supplies 115V/100W electrical power to operate accessories or equipment . Press the AC Inverter button to activate .
AC Inverter*
(Located behind center console)
See section 4 in the Owner’s Manual for more information .
•The power outlets are inactive when the ignition is in the OFF position
•The Multimedia USB data por t is located next to the Power Outlets A
•USB Charger does not suppor t data transfer
QUICK TIPS
REMINDERS:
•
Using the power outlets (accessor y plugs) for prolonged periods of time with the Engine Star t/Stop but ton in the ACC position (Engine OFF) may cause the bat ter y to discharge
•Only use manufacturer cables that came with your device as third par t y cables may cause damage to the device
•The Multimedia USB Por t B in the center panel charges more slowly than the USB Chargers C throughout the vehicle
Power Outlets A : Use the power outlets for mobile phones and other devices designed to operate on a 12V (180W max) power outlet .
Multimedia USB Port B : Use the USB port to connect USB audio devices and smartphone devices .
USB Charger Ports C : Devices can be recharged using a USB cable . The Engine Start/Stop button needs to be in the ACC/ON/START position to operate the USB Charger .
12V180WUSB
(Located in center panel in front of gearshift)
Multimedia USB Ports, Power Outlets & USB Charger Ports
CBA
See section 4 in the Owner’s Manual for more information .
Page 46 of 70
AUTO
OFFA/C
SYNC888ADS OFFAUTO888AUTO888
CENTER PANEL
Automatic Climate Control System
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Automatic Climate Control Operation Video
Auto Defogging System (ADS) Video
QR CODES
*IF EQUIPPED44TELLURIDE FEATURES & FUNCTIONS GUIDE
A
BGCHDIEF
J
REMINDERS:
•
Continuous use of the climate control system in the recirculated air position may allow humidit y to increase inside the vehicle which may fog the glass and obscure visibilit y
•
When in AUTO mode, Air Flow Mode and Fan Speed do not display on the Climate Control Display
•
Cold or warm ambient air may flow in through vents if Recirculated Air but ton is not pressed ON (LED lit)
CENTER PANEL
Face-Level Floor-Level
Bi-Level Floor/Defrost-Level
Tri-Zone Climate Control
Pressing the SYNC button J synchronizes all climate control zones (driver, passenger, and rear) to the driver ’s temperature control .
Auto Defogging System (ADS)
Auto defogging is designed to reduce the fogging up of the inside of the windshield by automatically sensing the moisture of the inside of the windshield . The system will automatically change to defrost mode when needed .
The ADS is set ON by default . To cancel ADS, press the Front Defrost button C for three seconds, when the ignition is in on (ADS OFF icon will illuminate) . To turn ADS on again, press the Front Defrost button for three seconds .
Defrost Outside Windshield
1 . Set fan speed to the highest position D
2 .
Set temperature to hot A
3 .
Press the front defrost button C
4 . Defog Inside Windshield
5 . Set fan speed to highest position D
6 . Set temperature to highest position A
7 . Press the front defrost button C
Climate Control Auto Function
Press AUTO A to select full auto operation . In AUTO mode the driver and front passenger have full control of their own temperature zones . The mode, fan speed, air intake and air conditioning will activate and adjust accordingly to achieve the temperature settings for each zone .
To set temperatures:
•Tu r n A to set the driver ’s zone temperature
•Tu r n J to set the front passenger ’s zone temperature
A AUTO (Automatic) Climate Control button
B System OFF button
C Front Windshield Defrost button
D Fan Speed Control buttons
E Rear Control Mode button
F Mode Select button
G Air Conditioning button
H Rear Window Defrost button
I Recirculated Air button
J SYNC (Synchronize All Zones) Temperature Control button
Front Climate Control
Air Flow Modes
To select air flow modes, press the Mode Select button F:
•When the Climate Control System’s temperature is turned up to high heat or low cool, the Seat Warmers / Ventilated Seats turn on automatically
QUICK TIP
For illustrative purposes only . Your actual display, buttons and/or features may vary . See section 4 in the Owner’s Manual for more information .
Page 48 of 70
CENTER PANEL
See section 5 in the Owner’s Manual for more information .
*IF EQUIPPED46TELLURIDE FEATURES & FUNCTIONS GUIDE
CENTER PANEL
REMINDERS:
•
To reduce the risk of an accident, do not activate Auto Hold while driving downhill, backing up or parking your vehicle
•
Do not solely rely on the Auto Hold system to keep the vehicle stopped . Always pay at tention to traf fic and road conditions, and be prepared to depress the brakes
•
Auto Hold only operates when the vehicle is in Drive or Neutral
•
Auto Hold turns off when the ignition is cycled
Auto Hold
Auto Hold temporarily maintains the vehicle at a standstill even if the brake pedal is not depressed after the driver brings the vehicle to a complete stop by depressing the brake pedal . Auto Hold can be turned On/Off using the
AUTO HOLD button A on the center panel . Before Auto Hold will operate, the driver ’s door, engine hood and liftgate must be closed and the driver ’s seat belt must be fastened .
Depress the brake pedal, start the engine and then press the AUTO HOLD button A . The white Auto Hold indicator will come on indicating the system is in standby .
The Auto Hold indicator, which is in the instrument cluster, has four states:
White: Standby – When the vehicle is in Park and at a standstill, and the AUTO HOLD button A is turned ON, the indicator will illuminate white . While driving the vehicle (vehicle is not at a standstill), the Auto Hold indicator will remain white .
Green: Engaged – When coming to a complete stop and depressing the brake pedal, the Auto Hold indicator changes from white to green .
OFF (not illuminated) – The indicator will turn OFF when the AUTO HOLD button A is manually turned OFF or when the EPB is manually turned ON .
Yellow: Malfunction – When the indicator is illuminated yellow, there may be a system malfunction . Take your vehicle to a local Kia dealer .
A
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electric Parking Brake / Auto Hold Video
QR CODE
Page 49 of 70
CENTER PANEL
See section 5 in the Owner’s Manual for more information .
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED47
CENTER PANEL
REMINDERS:
•
As a bulb check, the EPB malfunction indicator will illuminate for approximately 3 seconds when the ignition switch is turned ON
•
If the warning light does not illuminate temporarily or remains continuously lit, take your vehicle to an authorized Kia dealer and have the system checked
•
The EPB should not be operated while the vehicle is moving
•
A click or electric brake motor sound may be heard while operating or releasing the EPB . These conditions are normal and indicate that the EPB is functioning properly
The Electronic Parking Brake (EPB) system utilizes an electric motor to engage the parking brake .
Applying the Parking Brake
Depress the brake pedal and pull up the EPB switch A . Ensure that the indicator light is illuminated on the instrument cluster .
Releasing the Parking Brake
The EPB will automatically release when the shifter is placed in Reverse or Drive . To release EPB manually, depress the brake pedal, then press the EPB switch A , with the ignition switch in the ON position . Ensure that the indicator light is OFF .
Electronic Parking Brake (EPB)
•Pull up and hold the EPB switch again to increase brake pressure if parked on a decline or incline
•When leaving your keys with parking lot at tendants or valet, make sure to inform them how to operate the EPB
•If parked on a steep incline, pull up the EPB switch for more than 3 seconds for a firmer EPB application vehicle slows down . When the vehicle stops, 1st gear is automatically selected
QUICK TIPS
A
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electric Parking Brake / Auto Hold Video
QR CODE
Page 50 of 70
CENTER PANEL
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Idle, Stop & Go (ISG) System Video
QR CODE
*IF EQUIPPED48TELLURIDE FEATURES & FUNCTIONS GUIDE
•The ISG system is disabled when:
-A seat belt is unfastened
-The hood or a door is opened
-Bat ter y condition is poor
-The front or rear defroster is turned on
-Engine coolant temperature is low
-The outside ambient temperature is too low/high
-Emission control devices activate
-The vehicle is on a steep slope
QUICK TIPS
CENTER PANEL
A
Idle, Stop & Go (ISG) System
The ISG system is designed to help reduce fuel consumption by automatically shutting down the engine when the vehicle is at a standstill .
When the ISG system is ON and the vehicle is at a standstill, the engine will stop, and the green AUTO STOP indicator A on the instrument cluster will illuminate .
The engine will restart when the brake pedal is released or the shift lever is moved from D (Drive) to the R (Reverse) position or to Manual Shift mode . When the engine restarts, the green AUTO STOP indicator on the instrument cluster will turn off .
To deactivate the ISG system, press the ISG OFF button B . If you press it again, the system will be activated .
See section 5 in the Owner’s Manual for more information .
Images are for illustrative purposes only and may not reflect actual feature or operation .
EPB
AUTO
08
CH
12
3
4
5
6
7
x1000rpm
AUTO
HOLD
160
00
20
40
60
200
220
240
260
80
180
100
160
1
20 140
E F
2040
60
80
100
12 0
1 4 0
MPH
km/h
(Type A instrument cluster shown)
OFF
B
REMINDERS:
•
ISG is active by default at vehicle star tup . When the ignition is cycled, ISG will turn ON again
•
Under cer tain conditions, the engine will restar t automatically even if the brake pedal is still depressed
•
If the AUTO STOP indicator is continuously blinking yellow and the ISG but ton LED is on, please contact an authorized Kia dealer and indicate that the EPB is functioning properly
Page 54 of 70
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Rear Occupant Alert (ROA) with Ultrasonic Sensors Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED52TELLURIDE FEATURES & FUNCTIONS GUIDE
•The 1st aler t message will not display on Instrument Cluster if the rear doors are never opened . Either rear doors must be opened after unlocking the vehicle before the system will activate .
•To temporarily disable aler ts, press the OK but ton B on the Steering Wheel while the message is displayed
•To turn the aler t off while sounding, press the unlock but ton on the Smar t Key or press the door lock but ton on the door handle
•Must be enrolled in UVO ser vices and Kia Access app installed on the phone to receive ROA aler t notifications on your smar tphone
QUICK TIPS
S E AT I N G
SEATING
CRUISE
CANCEL
RES
OK SET
This system is not a substitute for one’s attention and may not detect all movement within the vehicle . Always check the vehicle’s interior before exiting .
Images are for illustrative purposes only and may not reflect actual feature or operation .
See section 4 in the Owner’s Manual for more information .
Rear Occupant Alert (ROA) with Ultrasonic Sensors†4
Rear Occupant Alert (ROA) with Ultrasonic Sensors can help alert the driver when rear passenger(s) are left in the rear seats using the ultrasonic sensors and door monitoring . The system is designed to provide three separate alerts:
•The 1st alert is a message on the Instrument Cluster, “Check Rear Seats” A , and a chime will sound
After the 1st alert, when the doors are locked and there is movement detected in the rear seats, the horn will sound for about 25 seconds . This alert may activate up to eight times within 24 hours, if movement is still detected and system has not been disabled
•If you have installed the Kia Access with UVO Link app on your smartphone, logged in and activated the Rear Occupant Alert notification, a third alert (notification) will be sent to your phone
To turn the system on or off, in the Instrument Cluster, go to User Settings, select Convenience, and then Rear Occupant Alert .
Rear Occupant with Ultrasonic Sensors activates under the following conditions:
•A rear passenger door is opened and closed
•The ignition has been turned off
•The driver ’s door has been opened, then closed
•The doors are locked with the Smart Key or the door lock button on the door handle
Check rear seats
: Alarm OffOK
(But ton layout on right of steering wheel)
A
REMINDERS:
•
To avoid false aler ts, make sure the vehicle’s windows are rolled up
•
If objects such as boxes are stacked in front of the ultrasonic sensors, the system may not detect any movement
•
The ultrasonic sensors may occasionally detect movement in the vehicle and cause false aler ts, when there are no rear occupants present
. False aler ts can occur due to:
–The presence of insects near the system sensor
–Rushing air from a window that is rolled down
–Movement around the exterior of the vehicle
–Surrounding noise or vibration
–Vehicle passing through a car wash
–Movement in the driver or front passenger seat is detected
•
The Rear Occupant Aler t with Ultrasonic Sensors system may fail to detect movement and activate an alarm if:
–Movement is subtle or does not continue
–A small child sits directly in a seat without a car seat
–
A rear passenger is covered with an object such as a blanket, obstructing the sensor ’s view
B
Page 61 of 70
UVO
FRONTREAR
ONOFFDOOR
The sunroof and sunshade operation is controlled by a multidirectional switch/lever for the front and rear sunroofs
. The ignition needs to be in the ON position to operate the sunroof/sunshade .
Slide the sunshade and sunroof A :
Auto Open – Slide lever backward to the farthest position and release .
Auto Close – Slide the lever forward to the farthest position and release (manually close the Sunshade) .
Tilt the sunroof (front only) A :
Raise – Press lever upward
Lower – Push lever forward
Slide the rear sunshade B :
Auto Open – Slide the lever backward
Auto Close – Slide the lever forward
OTHER KEY FEATURES
See section 4 in the Owner’s Manual for more information .
Your vehicle’s sunroof controls may differ from that in the illustration .
Sunroof Operation*
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Sunroof Operation Video
QR CODE
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Cargo Cover & Storage Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED59
AB
OTHER KEY
FEATURES
•To stop the sunroof/sunshade at any position, press or pull the sunroof control lever in any direction
QUICK TIP
•Inser t the third-row seat belts into the retaining clips on the left and right sides before removing/installing Cargo Cover
QUICK TIP
REMINDERS:
•When closing, be mindful of any objects or persons
•
Sunshade must remain OPEN while sunroof is open
•
If the ignition is turned off with the Sunroof not fully closed, the Instrument Cluster LCD will display a warning message and a chime will sound for a few seconds
•
Do not adjust the sunroof or sunshade while driving . This could result in loss of control of the vehicle
(But ton located within overhead lamp console)
Cargo Cover Storage*
To store the Cargo Cover*, close the Cargo Cover and remove it from the slots by pulling the Cargo Cover ends inward C . Remove the luggage box cover .
On the left side, remove the small storage cover D to expose the Cargo Cover storage slot . Insert the Cargo Cover on the right side first . Compress the left end of the Cargo
Cover to slide it into the left slot . Replace the small storage cover and the luggage box cover .
C
D
(View from the rear looking in;left end of the cover shown)