lock Lancia Delta 2009 Owner handbook (in English)

166IN AN EMERGENCY
CYLINDER REPLACEMENTPROCEDURE
To replace the cylinder proceed as follows:
disconnect connection A-fig. 7;
turn the cylinder to be replaced anticlockwise and
raise it;
fit the new cylinder and turn it clockwise;
connect connection A to the cylinder and fit the trans-
parent tube B into the proper space.
fig. 7L0E0080m

IN AN EMERGENCY169
4
REMOVING THE SUBWOOFER
(versions with Bose HI-FI system, where provided)
IMPORTANT The following procedure only applies to ve-
hicles equipped with Bose Hi-Fi systems with Subwoofer
(where provided).
SUBWOOFER AND SMALL SPARE WHEEL
Proceed as follows to remove the Subwoofer:
open the luggage compartment, pull tab A-fig. 10 and
lift up the mat;
undo locking device A-fig. 8 and lift up the Subwoofer.
Then remove connection cable B from Velcro attach-
ment C;rest the Subwoofer to one side in the luggage com-
partment, remove the container and take out the small
spare wheel;
replace the wheel as described in this chapter.
After tyre replacement:
reposition the container and place the Subwoofer on
top of it, taking care to position it according to the in-
structions on the container (fig. 9) so that the arrow
on the spacer is pointing in the direction of travel;
rest cable B-fig. 8 into Velcro Attachment C to avoid
pinching it. Then tighten locking device A-fig. 8. Re-
place the luggage compartment mat.
fig. 8L0E0176mfig. 9L0E0177m

174IN AN EMERGENCY
After tyre replacement
stow the small spare wheel D-fig. 10 in the space pro-
vided in the luggage compartment;
fit the partially-opened jack in its box, forcing it light-
ly to prevent it from vibrating when travelling;
put the tools back into place in the container;
stow the container, complete with tools, into the spare
wheel and tighten the locking device B-
fig. 10;
put back the luggage compartment mat into the prop-
er position.
IMPORTANT Do not use an inner tube with tubeless tyres.
Periodically check the inflation pressure of the tyres and
small spare wheel.
IMPORTANT If you choose to install wheels of a different
type (with alloy rims instead of the steel ones or vice ver-
sa) you must change all the retaining bolts with others of
a suitable size and use a specific small spare wheel, with
different specifications.
It is advisable to keep the replaced bolts and small spare
wheel, as they are necessary if in future you decide to re-
install the original wheels.CHANGING A BULB
GENERAL INSTRUCTIONS
Before changing a bulb check the contacts for oxida-
tion;
blown bulbs must be replaced with others of the same
type and power;
after replacing a headlight bulb, always check its align-
ment for safety reasons;
when a bulb is not working, check that the corre-
sponding fuse is intact before replacing it: refer to the
“Replacing fuses” paragraph in this chapter for fuse
location.
Modifications or repairs to the electrical sys-
tem that are not carried out properly or do
not take the system’s technical specifications
into account can cause malfunctions leading to the
risk of fire.

176IN AN EMERGENCY
fig. 14L0E0084m
BULB TYPES fig. 14
Various types of bulbs are fitted to your car:
A. All glass bulbs: clipped into place. Pull to extract.
B. Bayonet bulbs: to remove this type of bulb from its
holder, press the bulb and turn it anticlockwise.
C. Cylindrical bulbs: release from the contacts to extract.
D. Halogen bulbs: release the fastening clip from the cor-
responding seat to remove the bulb.
E. Halogen bulbs: release the fastening clip from the cor-
responding seat to remove the lamp.

180IN AN EMERGENCY
SIDELIGHTS/DAYTIME LIGHTS
The direction indicators/daylight lights are LED-based.
Contact a Lancia dealership to have there lights replaced.
DIRECTION INDICATORS
Front indicators
To change the bulb, proceed as follows:
remove the protective cover C-fig. 15;
press down near the bulb holder locking tabs (shown
in fig. 18 by the arrows) and simultaneously pull the
unit;
remove the bulb A and replace it;
refit the protective cover C.Side indicators
To change the bulb, proceed as follows:
work on lens A-fig. 19 to compress catch B, then pull
the unit outwards;
turn the bulb holder C, anticlockwise, extract the press-
fitted bulb D and replace it;
refit the bulb holder C in the lens and turn it clock-
wise;
refit the unit making sure that internal catch B clips
into position.
fig. 18L0E0157mfig. 19L0E0158m

182IN AN EMERGENCY
THIRD BRAKE LIGHT fig. 23
Contact a Lancia Dealership to replace the LED lights in
the third brake light.
NUMBER PLATE LIGHTS
To change the bulb proceed as follows:
operate in the area shown by the arrows and remove
the lens cover unit A-fig. 24;
fig. 23L0E0162mfig. 25L0E0164m
fig. 24L0E0163m
turn the bulb holder B-fig. 25 anti-clockwise;
remove the bulb C and replace it.

IN AN EMERGENCY191
4
FUSE SUMMARY TABLE - Dashboard control unit
F12
F12
F13
F13
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F417.5
15
7.5
15
5
–
20
20
5
20
7.5
10
10
30
7.538
38
38
38
38
–
38
38
38
38
38
38
38
38
38
CONSUMERS FUSE AMPERE DIAGRAM
Right dipped beam headlight
Right dipped beam headlight (Xenon gas discharge bulb)
Left dipped beam headlight, headlight alignment corrector
Left dipped beam headlight (Xenon gas discharge bulb)
Climate control system fan relay coil, body computer
Spare
Left rear electric window
Right rear electric window
Reversing lights, engine compartment control unit relay coils,
brake light pedal control (normally closed contact),
water in the diesel fuel sensor, air flow meter
Central locking system control unit, fuel
butterfly, dead lock, tailgate release
Third brake light, instrument panel, Adaptive Headlights Node,
control unit on left-hand gas discharge headlight
Rear and front courtesy ligths (where fitted), sun visor lights,
glove compartment ligtht and luggage compartment light
Radio, radio-navigator, Blue&Me Node, alarm siren,
alarm system on courtesy light, climate control unit, tyre
pressure detection control unit, diagnostic connector,
rear courtesy light
Heated rear window
Electric door mirror demisters, demisters
on windscreen jets

196IN AN EMERGENCY
TOWING THE CAR
The tow ring provided with the car is housed in the tool
box under the luggage compartment mat.
FASTENING THE TOW RING fig. 43-44
Proceed as follows:
release cap A;
take the tow hook B from its seat in the tool support;
tighten the ring on the rear or front threaded pin.
fig. 43L0E0090mfig. 44L0E0091m
Before starting towing operations, turn the ig-
nition key to MAR and then to STOP, without
extracting it. If the key is extracted, the steer-
ing wheel lock will be automatically activated, thus
preventing steering. The power brakes and the elec-
trical power steering will not work while the car is be-
ing towed. More effort on the brake pedal and steer-
ing wheel will therefore be required. Do not use wires
for towing. Do not jerk. Make sure not to damage parts
in contact with the car while towing. Respect the spe-
cific rules of the Highway Code when towing the car
specifically in relation to the towing device and the be-
haviour to maintain on the road. Do not start the en-
gine while towing the car.

CARE AND MAINTENANCE199
5
SCHEDULED SERVICING PLAN
Petrol versions
Thousands of kilometres
Check tyre condition/wear and adjust pressure if required
Check lighting system operation (headlights, direction indicators, hazard lights,
passenger compartment lights, boot lights, instrument panel warning lights, etc.)
Check windscreen wiper/washer operation
Check the position/wear of the windscreen/rearscreen wiper blades
Check condition and wear of front disc brake pads and
brake pad wear indication
Check rear disc brake pad condition and wear
Visually inspect the condition of: bodywork, underbody
protection, pipes and hoses
(exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.)
Check cleanness of bonnet and boot locks and
linkage cleanness and lubrication;
Check and top up, if required, fluid levels (engine coolant, brake/hydraulic
clutch fluid, windscreen washer fluid, battery fluid, etc)
Check the handbrake lever stroke and adjust it, if necessary
visually inspect the condition of the accessory drive belt
Visually inspect the condition of the toothed timing drive belt30 60 90 120 150 180
    
    
    
    
    
    
    
    
    
    



CARE AND MAINTENANCE201
5
Diesel versions
Thousands of kilometres
Check tyre condition/wear and adjust pressure if required
Check lighting system operation (headlights, direction indicators, hazard lights,
passenger compartment lights, boot lights, instrument panel warning lights, etc.)
Check windscreen wiper/washer operation
Check the position/wear of the windscreen/rearscreen wiper blades
Check condition and wear of front disc brake pads and
brake pad wear indication
Check rear disc brake pad seal condition and wear
Visually inspect the condition of: bodywork, underbody
protection, pipes and hoses
(exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.)
Check cleanness of bonnet and boot locks and
linkage cleanness and lubrication
Check and top up, if required, fluid levels
(engine coolant, brake/hydraulic clutch fluid, windscreen washer fluid, battery fluid, etc)
Check the handbrake lever stroke and adjust it, if necessary
Check and if necessary adjust the auxiliary
drive belts (excluding engines equipped with automatic tensioners)
Check exhaust fumes/emissions
Visually inspect the condition of the auxiliary drive belt35 70 105 140 175