key battery Lancia Musa 2009 Owner handbook (in English)

13
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
THE KEY AND
DOOR LOCKING
KIT
CODE CARD Fig. 10
(Optional for versions/markets
where applicable)
The car is delivered with the ignition
key and the CODE card which bears
the following data:
❒the mechanical key code Bto be
given to the Lancia Dealership
when ordering duplicate keys.
IMPORTANT In order to ensure per-
fect efficiency of the electronic devices
inside the keys, they should never be
exposed to direct sunlight.MAIN KEY WITH REMOTE
CONTROL fig. 11
The metal insert of the key Ais re-
cessed in the grip.
The key operates:
❒the ignition switch;
❒the lock of the door on the driver’s
side;
❒the lock/release device of the fuel
flap (on versions equipped with a
lockable fuel plug)
fig. 10L0D0376m
All the keys and the CODE
card must be handed over to
the new owner when selling
the car.
fig. 11L0D0377m
❒engagement of the device, D-fig.
12, for locking external opening of
the front and rear doors when the
electric system does not work (e.g.
the battery is down);
❒engagement of the child safety
lock device, E-fig. 12, installed on
the rear doors.
ButtonB-fig. 11enables opening of
the metal insert A.
fig. 12L0D0246m
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 13

16
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Request for additional remote
controls
The system acknowledges up to 8 re-
mote controls. Should a new remote
control be necessary, contact a Lancia
Dealership and be ready to present
the CODE card, a personal identity
document and the car’s ownership
documents.
Replacing the battery of the key
with remote control fig. 16
Battery replacement:
❒press button Aand bring the metal
insertBto the “open” position;
❒turn the screw Cusing a fine bit
screwdriver;
❒take out the battery case Dand re-
place the battery Erespecting its
polarity;
❒fit the battery case Dback inside
the key and lock it turning screw
C.
fig. 16L0D0379m
Used batteries are harmful to
the environment. They
should be disposed of as
specified by law in special
containers or taken to a Lancia Deal-
ership, which will take care of their
disposal.
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 16

17
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
(SPARE) MECHANICAL
KEY, fig. 17-18
Depending on the version, the car is
either supplied with a recessed key 1
or fixed key 2.
The metal insert Aof the key 1is re-
cessed in the grip.
The button Bactivates opening of the
metal insert A.
The metal insert Ais placed back in
the grip as follows.
❒Press button Band hold it pressed.
❒Move the metal insert A.
❒Release buttonBand turn the
metal insertAuntil hearing the
click that indicates correct locking.The keys are used to activate:
❒the ignition switch;
❒the lock of the door on the driver’s
side;
❒the fuel flap lock/release (on ver-
sions supplied with a lockable
plug)
❒engagement of the child safety
lock device when the electric sys-
tem does not work (e.g. when the
battery is down);
❒engagement of the child safety
lock device on the rear doors.
fig. 17L0D0014mfig. 18L0D0380m
Only press button B with
the key away from your
body, specifically from your eyes
and from objects which could get
damaged (e.g. your clothes). Do not
leave the key unattended, because
someone, a child especially, may ac-
cidentally press the button while
handling the key.
WARNING
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 17

36
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
New mission
The new mission begins after:
– “manual” resetting by the user, by
pressing the relevant button;
– “automatic” resetting, when the
“Trip distance” reaches 9999.9 km or
when the “Travel time” reaches 99.59
(99 hours and 59 minutes);
– disconnection/reconnection of the
battery.
IMPORTANT The reset operations
performed after the “General Trip”
message appears are used to also re-
set the “Trip B”, which, on its turn, is
used to reset the values of the corre-
sponding function. Travel time
This value shows the time elapsed
since the start of a new mission.
IMPORTANT If information is not
available, the message “----” will ap-
pear instead of the Trip Computer
values. Displaying of the values will
be resumed regularly when normal
operation is restored without resetting
the values displayed before the failure
nor starting a new mission.
TRIP button fig. 32
ButtonTRIPlocated on the top of the
right steering column stalk is used
(with ignition key at MAR) to display
and reset the previously described val-
ues to start a new mission:
– short pressing to display the differ-
ent values;
– long pressing to reset and then start
a new mission. Values displayed
Range
It indicates the distance left to travel
based on the fuel in the tank assuming
that driving conditions will not change.
The message “----” will appear on the
display in the following cases:
- the range value is below 50 km (30
miles) or the fuel level is below 4
litres;
– car left parked with engine running
for long.
Trip distance
This value shows the distance covered
from the start of a new mission.
Average consumption
This value shows the average con-
sumption from the start of a new mis-
sion.
Instant consumption
This indicates the fuel consumption.
The value is constantly updated. The
message “----” will appear on the dis-
play if the car is parked with the en-
gine running.
Average speed
This value shows the car average
speed as a function of the overall time
elapsed since the start of the a mis-
sion.
fig. 32L0D0027m
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 36

69
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
LIGHTS
FRONT LIGHT fig. 76
SwitchA-turn on/off these lights.
With switch Ain central position,
lightsCandDwill turn on/off when
opening/closing the front doors.
With switch Apressed on the left side,
lightsCandDwill always stay off.
With switch Apressed on the right
side, lights CandCwill always stay
on.
Light turning on/off is gradual.
SwitchBperforms the spot function;
with light off, it will turn on:
❒lightCif pressed on the left side;
❒lightDif pressed on the right side.Light timing when getting into the
car
Lights will turn on as follows:
❒for about 10 seconds when un-
locking the doors;
❒for about 3 minutes when opening
one of the doors;
❒for about 10 seconds when closing
the doors (within 3 minutes).
Timing will stop when turning the ig-
nition key to MAR.
Light timing when getting out of the
car
After removing the key from the igni-
tion switch, the lights will turn on as
follows:
❒within 2 minutes from turning the
engine off for about 10 seconds;
❒when opening one of the doors for
about 3 minutes;
❒when closing the doors for about
10 seconds (within 3 minutes).
Timing will stop automatically when
locking the doors. IMPORTANT Before getting out of
the car, make sure the switch is at
central position: lights off with doors
closed in order to avoid draining the
battery.
In any case, if the switch is left inad-
vertently to the On position, the lights
will turn off automatically 15 minutes
after turning the engine off.
Ceiling light timing
To facilitate getting in/out of the car
at night or with poor lighting, 2 dif-
ferent timed switching on modes have
been provided:
fig. 76L0D0077m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 69

72
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
INERTIAL FUEL
CUT-OFF SWITCH
It is located in the bottom, near the
passenger side pillar; to access it, re-
move the carpet. It trips in the event
of a collision cutting the fuel supply
off; as a consequence, the engine turns
off.
When the switch trips, the instrument
panel warning light
èturns on and
the relevant message (where pro-
vided) is displayed on the reconfig-
urable multifunctional display.
Carefully inspect the car to ensure
that there are no fuel leaks, e.g. from
the engine compartment, under the
car or near the tank.
If, after a crash, you smell
fuel or see leaks from the
fuel system, do not reset the switch
to avoid fine risk.
WARNING
fig. 84L0D0388m
If no fuel leaks are detected and the
car can start, press button A-fig. 84
in order to reactivate the fuel feeding
system and turn the lights on.
After a crash, turn the ingition key to
STOPto avoid draining the battery.
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 72

114
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
STARTING
THE ENGINE
The car is provided with an electronic
engine lock device: refer to “The Lan-
cia CODE system” paragraph in
“Dashboard and controls” if you can-
not start the engine. The engine may
be noisier during the first seconds of
operation, particularly after a long pe-
riod of inactivity. This does not impair
functionality and reliability and is
typical of hydraulic tappets: the dis-
tribution system selected for the petrol
engines of your car in order to limit
the maintenance required.
STARTING PROCEDURE FOR
PETROL VERSIONS
Proceed as follows:
❒ensure that the handbrake is up;
❒put the gear lever into neutral;
❒press the clutch pedal down to the
floor without touching the accel-
erator;
❒turn the ignition to AV Vand re-
lease the key as soon as the engine
starts.If the engine does not start at the first
attempt, return the ignition key to
STOPbefore repeating starting.
If, when the ignition key is on MAR,
the instrument panel warning light
Yremains on together with the
warning light U, turn the key to
STOPand then back to MAR; if the
warning light remains on, try with the
other keys provided with the car.
Is is dangerous to let the en-
gine run in enclosed spaces.
The engine depletes the oxygen and
discharges carbon dioxide, carbon
monoxide and other toxic gases.
WARNING
In the first period of use, we
recommend to avoid exces-
sive stress for the car (for in-
stance excessive accelera-
tions, extended travel at maximum
speed, sudden braking etc.).
With engine off, do not leave
the key in the ignition switch
on MAR to prevent draining
the battery.
If you still cannot start the engine,
perform emergency start (see “Emer-
gency start” in chapter “In an emer-
gency”) and then contact a Lancia
Dealership.
IMPORTANT Never leave the ignition
key to MARwhen the engine is off.
STARTING PROCEDURE FOR
MULTIJET VERSIONS
Proceed as follows:
❒ensure that the handbrake is up;
❒put the gear lever into neutral;
❒turn the ignition key to MAR; the
instrument panel warning lights
m,
UandY;
113-124 MUSA 1ed GB 10-07-2008 9:37 Pagina 114

116
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
PARKING THE CAR
Proceed as follows:
❒stop the engine and engage the
handbrake;
❒when on a slope, engage a gear
(engage first gear if the car is
faced uphill or reverse if it is faced
downhill) and leave the wheels
steered.
When parking the car on a steep
slope, it is advisable to also place a
wedge or a rock under the wheels.
PROLONGED parking with a wheel
on the pavement or steered against a
step should be avoided. Do not leave
the ignition key on MARto prevent
draining the battery. Always remove
the key when you leave the car.
HANDBRAKE
The handbrake lever is located be-
tween the two front seats.
Pull the lever upwards to operate the
handbrake.
Four or five notches are normally suf-
ficient to lock the car on flat terrain,
while nine or ten may be necessary on
a steep slope with the car loaded. IMPORTANT If this is not the case,
contact a Lancia Dealership to have
the handbrake adjusted.
When the handbrake lever is pulled
up and the ignition key is on MAR,
the instrument panel warning light
xwill turn on.
Proceed as follows to release the
handbrake:
❒slightly lift the handbrake and
press release button A-fig. 1;
❒keep button Apressed and lower
the lever. Warning light
xwill
turn off.
Press the brake pedal when carrying
out this operation to prevent the car
from moving accidentally.
IMPORTANT If the handbrake lever
tends to reach end of its stroke
(groove on the central console), con-
tact a Lancia Dealership to have the
handbrake adjusted.
fig. 1L0D0149m
Never leave children unat-
tended in the car. Always re-
move the ignition key when
leaving the car and take it
out with you.
113-124 MUSA 1ed GB 10-07-2008 9:37 Pagina 116

127
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
If when turning the key to
MAR the warning light ¬does not turn on or stays on during
car travel (together with the message
on the multifunctional display,
where provided), a failure may have
occurred in the restraint systems. In
this case the airbags or pretension-
ers may not be deployed after an im-
pact or, in a minor number of cases,
they may be deployed accidentally.
Contact Lancia Dealership immedi-
ately to have the system checked im-
mediately.
The failure of the warning
light
¬is indicated by the
warning light flashing longer than
the expected 4 seconds“, thus sig-
nalling that the front passenger
airbag is deactivated. In addition,
the airbag system automatically dis-
ables the airbag on the passenger’s
side (both front and side airbags,
where provided). In this case, the
warning light
¬does not neces-
sarily indicate a failure in the re-
straining systems. Contact Lancia
Dealership immediately to have the
system checked.
WARNING
WARNING
HOT ENGINE COOLANT
(red)
When the ignition key is
moved to MAR, the warning
light turns on and should go off after
a few seconds.
The warning light turns on when the
engine is overheated.
If the warning light comes on, proceed
as follows:
❒during normal travel: stop the car,
stop the engine and check that the
water level in the vessel is not un-
der the MINline. If this is the case,
wait for a few minutes for the en-
gine to cool down. Then, slowly
and carefully open the cap, top-up
with coolant and check that the
level is between the MINandMAX
reference lines on the vessel. Also
check for leakages. Should the
warning light turn on again at the
next start-up, contact Lancia Deal-
ership.
u
❒If the vehicle is used under severe
conditions(e.g. towing of trailers up-
hill or fully loaded vehicle): slow
down and stop the car if the warn-
ing light stays on. Stop for 2 or 3
minutes with the engine running
and slightly accelerated to favour
better coolant circulation. Then stop
the engine. Check correct fluid level
as described above.
IMPORTANT Under severe use of the
car, keep the engine on and slightly
accelerated for a few minutes before
switching it off.
The display will show the dedicated
message.
LOW BATTERY
CHARGE (red)
When the ignition key is
moved to MAR, the warning
light turns on and should go out as
soon as the engine is started (with the
engine running at idle speed a brief
delay in going out is allowed). If the
warning light stays on, immediately
contact Lancia Dealership.
w
125-134 MUSA 1ed GB 10-07-2008 9:38 Pagina 127

136
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
OPENING/
CLOSING OF
DOORS
Emergency device for locking doors
from the outside
The doors are fitted with an emer-
gency device so that they can be
closed using a lock in the event of a
current failure.
In this case, to close the doors of the
car, proceed as follows:
❒fit the ignition key into the revolv-
ing plug B-fig. 1.
❒turn it to 1and close the door.
fig. 1L0D0247m
STARTING
THE ENGINE
STARTING WITH AN AUXILIARY
BATTERY
If the battery is lat, the engine may be
started using an auxiliary battery with
the same capacity or a little higher
than the flat one.
Proceed as follows:
❒connect the positive terminals (+
sign near the terminal) of the two
batteries using an appropriate ca-
ble; To re-open the door, proceed as fol-
lows:
❒fit the ignition key in the revolving
plug of the lock on the driver’s side
and turn it anticlockwise
❒open the door on the driver side
❒from the inside of the car, open the
remaining doors by lifting the re-
spective levers on the door han-
dles.
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 136