brake LAND ROVER DEFENDER 1996 Owners Manual

BRAKES
1
OVERHAUL REV: 05/99
Key to master cylinder
1.Water ingress seal
2.Transfer housing
3.Vacuum seal
4.Guide ring
5.Retaining ring
6.'O' ring seal
7.Primary plunger assembly
8.'L' seal
9.Secondary plunger10.Washer
11.Recuperating seal (primary cup)
12.Seal retainer
13.Springs
14.Swirl tube
15.Master cylinder body
16.Reservoir seals
17.Reservoir
18.Low fluid level switch and cap

70BRAKES
2
OVERHAUL MASTER CYLINDER
Service repair no - 70.30.09
Before starting overhaul procedure refer to general
brake service practice
See Repair, General brake
service practice
.
Dismantling master cylinder
1.Disconnect battery and remove master cylinder
from servo
See Repair, Master cylinder.
2.Before commencing overhaul procedure
thoroughly clean master cylinder and inspect
outer surfaces for damage and condition, renew
complete assembly if necessary.
3.The reservoir is a push fit in master cylinder and
secured by seals. Carefully ease reservoir from
master cylinder by rolling it from seals as
illustrated.
4.Using soft jaws, one either side of master
cylinder flange and clamp flange in a suitable
vice. Remove water ingress 'O' ring seal from
master cylinder to servo flange and discard.
5.Hold outside of transfer housing with a suitable
pair of grips, carefully pull, while working pliers in
a backwards and forwards rocking motion to
ease housing off master cylinder, discard
housing and vacuum seal.
6.Withdraw 2 reservoir seals from master cylinder
and note their positions in inlet ports for
reassembly. Discard both seals.
7.Remove retaining ring and 'O' ring seal from
machined outer surface of master cylinder,
discard both seal and retaining ring.

BRAKES
3
OVERHAUL
8.Remove guide ring from mouth of master
cylinder which supports primary plunger
assembly and place to one side, this component
is not part of master cylinder service kit and is to
be refitted on assembly of unit.
9.Pull primary plunger assembly out of master
cylinder.
NOTE: The primary plunger assembly
cannot be broken down any further and is
serviced as a complete unit. Discard
assembly.
10.The secondary plunger assembly will remain at
bottom of master cylinder bore, plunger can be
easily expelled by tapping assembly on a piece
of timber until plunger appears at cylinder mouth,
carefully pull plunger from master cylinder.
11.If swirl tube was not expelled at same time as
secondary plunger, repeat above operation to
expel it from bottom of master cylinder bore and
discard.12.Clean all parts with Girling cleaning fluid or
unused brake fluid and place cleaned parts on to
a clean sheet of paper. Inspect cylinder bore and
plungers for signs of corrosion, ridges and score
marks. Provided working surfaces are in perfect
condition, new seals from a Girling Service
repair kit may be used.
Renewing secondary plunger seals
A.Springs
B.Seal retainer
C.Recuperating seal (primary cup)
D.Washer
E.'L' seal
13.Remove components above from secondary
plunger and discard:
NOTE: A small screwdriver with end
rounded and polished is required to
remove 'L' seal. DO NOT damage
secondary plunger.
14.Coat new seals in unused brake fluid and firstly
fit 'L' seal to plunger.
15.Fit washer followed by recuperating seal. Fit seal
retainer and springs, ensure springs are
correctly seated.

70BRAKES
4
OVERHAUL Assembling master cylinder
CAUTION: It is important that the following
instructions are carried out precisely,
otherwise damage could be caused to new
seals when inserting plungers into cylinder bore.
Generous amounts of new brake fluid should be
used to lubricate parts during assembly.
NOTE: Thoroughly check that no debris is
lodged in fluid passageways and drillings.
If debris is found, carefully remove,
re-clean cylinder and re-check.
16.Fit new swirl tube to bottom of cylinder bore.
17.Lubricate secondary plunger and cylinder bore.
Offer plunger assembly to cylinder until
recuperation seal is resting centrally in mouth of
bore. Gently introduce plunger with a circular
rocking motion, as illustrated. Ensuring that seal
does not become trapped, ease seal into bore
and slowly push plunger down bore in one
continuous movement.
18.Fit primary plunger assembly using same
method as for secondary plunger, push plunger
down bore.
19.Fit original guide ring to support primary plunger.
20.Coat a new 'O' ring with brake fluid and fit to its
respective groove on outer location surface of
master cylinder.
CAUTION: 'O' ring should not be rolled
down outer location surface of master
cylinder but should be slightly stretched
and eased down cylinder and into its groove. Do
not over stretch seal.21.Fit a new retaining ring on outer surface of
master cylinder ensuring that serrations of ring
are facing mounting flange.
22.Fit two new reservoir seals in their respective
ports.
23.Fit a new vacuum seal to either primary plunger
or to bottom of transfer housing bore, open face
of seal towards primary plunger guide ring.
24.Lubricate vacuum seal with brake fluid, fit
transfer housing to master cylinder, push
housing fully up to cylinder mounting flange. Do
not adjust transfer housing after fitting.
25.Lubricate a new water ingress seal with brake
fluid, slightly stretch seal and ease it down
housing until seal is in correct position between
housing and flange.
26.Roll reservoir into top of master cylinder,
reversing procedure described in instruction 3.
27.Fit master cylinder to servo
See Repair,
Master cylinder
.
28.Reconnect battery, and road test vehicle.

74WHEELS AND TYRES
6
REPAIRREV: 05/99 WHEELS
Remove
WARNING: The parking brake acts on
transmission, not rear wheels, and may
not hold vehicle when jacking unless
following procedure is used. If one front wheel
and one rear wheel is raised no vehicle holding or
braking effect is possible. Wheels MUST be
chocked in all circumstances.
Apply parking brake, select a gear in main
gearbox and engage low gear in transfer box.
1.Loosen 5 wheel nuts.
2.Using a suitable trolley jack, raise vehicle and
place on axle stands
See INTRODUCTION,
Information, Jacking
.
3.Remove wheel nuts and carefully withdraw
wheel over studs.
Refit
4.Ensure that retaining studs and nuts are clean.
5.Alloy wheels: Lightly coat wheel mounting spigot
face with a suitable anti-seize compound to
minimise possibility of adhesion between wheel
and spigot face.
6.Refit wheel taking care not to damage stud
threads. (Do not apply oil).
7.Fit wheel nuts and turn by hand for at least three
full threads before using any form of wheel
wrench.
8.Tighten nuts as much as possible using a
suitable wrench.
9.Lower vehicle and finally tighten nuts to correct
torque sequence shown.
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)