drain bolt LAND ROVER DEFENDER 1999 User Guide

ENGINE
27
REPAIR Refit
9.Clean sump and mating faces.
10.Apply a bead of sealant, Part No. STC 3254 to
joint faces of timing chain cover and crankshaft
rear oil seal.
11.Position new sump gasket.
CAUTION: Gasket must be fitted dry.
12.Position sump, fit bolts ensuring they are in their
correct fitted position, lightly tighten bolts.
13.Fit bolts securing sump to gearbox bell housing
and tighten to15 Nm (11 lbf.ft).
14.Using sequence shown, tighten sump bolts to25
Nm (18 lbf.ft).
15.Tighten sump to gearbox bell housing bolts to50
Nm (37 lbf ft).
16.Fit new gasket to centrifuge drain pipe and
tighten bolts to10 Nm (7 lbf.ft).
17.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair.
18.Refill engine with oil.
19.Reconnect battery negative lead.
20.Refit battery cover.
ProCarManuals.com

ENGINE
29
REPAIR VALVE - RELIEF - OIL PRESSURE
Service repair no - 12.60.56
Remove
1.Remove sump gasket.See this Section.
2.Remove and discard oil pressure relief valve
plug from oil pump housing.
3.Remove spring and valve.
Refit
4.Clean valve and spring.
5.Clean valve seating inside oil pump housing.
6.Lubricate valve and seating.
7.Fit valve and spring to pump.
8.Apply Loctite 243 sealant to threads of a new
plug.
9.Fit plug and tighten to23 Nm ( 17 lbf.ft).
10.Fit sump gasket.See this Section.
11.Check engine oil level, top-up if necessary.COOLER - ENGINE OIL
Service repair no - 12.60.68
Remove
1.Drain cooling system.See COOLING
SYSTEM, Adjustment.
2.Remove centrifuge assembly.See this
Section.
3.Remove clutch housing bolt and release coolant
pipe from rear of engine.
4.Release clip and coolant hose from oil cooler.
5.Disconnect oil pressure switch multiplug.
6.Remove oil filter element using a suitable strap
wrench.
7.Remove 3 bolts, remove oil filter adaptor and
discard gasket.
8.Remove 7 bolts, remove oil cooler and discard
gasket.
9.Remove oil pressure switch.
ProCarManuals.com

12ENGINE
30
REPAIR Refit
10.Clean oil cooler and mating faces.
11.Fit oil pressure switch and tighten to9Nm(7
lbf.ft).
12.Position oil cooler using a new gasket and
tighten bolts to25 Nm (18 lbf.ft).
13.Position oil filter adaptor, fit new gasket and
tighten bolts to25 Nm (18 lbf.ft).
14.Position oil filter element hand tight then a
further half turn.
15.Position coolant hose to oil cooler and secure
clip.
16.Position coolant pipe and tighten clutch housing
bolt to50 Nm (37 lbf.ft).
17.Connect oil pressure switch multiplug.
18.Fit centrifuge assembly.See this Section.
19.Refill cooling system.See COOLING SYSTEM,
Adjustment.
20.Top up engine oil.CENTRIFUGE ASSEMBLY
Service repair no - 12.60.90
Remove
1.Remove fixings and remove underbelly panel.
See CHASSIS AND BODY, Repair.
2.Remove 2 bolts securing centrifuge drain pipe to
engine sump and discard gasket.
3.Remove turbocharger.See FUEL SYSTEM,
Repair.
Models with air conditioning only
4.Remove auxiliary drive belt.See
ELECTRICAL, Repair.
5.Remove 4 bolts securing compressor and move
to one side.
ProCarManuals.com

ENGINE
31
REPAIR All Models
6.Remove 3 bolts securing centrifuge to engine oil
cooler.
7.Remove centrifuge and discard’O’ring.
8.Remove 2 bolts, remove drain pipe from
centrifuge and discard gasket.Refit
9.Clean mating faces of centrifuge, oil cooler and
sump.
10.Position drain pipe to centrifuge using new
gasket and tighten bolts to10 Nm (7 lbf.ft).
11.Position new’O’ring to oil cooler.
12.Position centrifuge and tighten bolts to25 Nm
(18 lbf.ft).
13.Align drain pipe to sump, fit new gasket and
tighten bolts to10 Nm (7 lbf.ft)
Models with air conditioning only
14.Position compressor and tighten bolts to25 Nm
(18 lbf.ft).
15.Fit auxiliary drive belt.See ELECTRICAL,
Repair.
All Models
16.Fit turbocharger.See FUEL SYSTEM, Repair.
17.Fit underbelly panel.See CHASSIS AND
BODY, Repair.
ProCarManuals.com

ENGINE
33
REPAIR TIMING CHAIN AND SPROCKETS
Service repair no - 12.65.13
Remove
1.Remove crankshaft front oil seal.See this
Section.
2.Remove cylinder head gasket.See this
Section.
3.Remove sump gasket.See this Section.
4.Release clip securing vacuum pump drain hose
to timing chain cover.
5.Remove 8 bolts securing timing chain cover.
6.Remove cover.
7.Remove timing chain and camshaft sprocket.
8.Remove 2 bolts and remove timing chain fixed
guide.
9.Remove bolt and remove timing chain adjustable
guide.
10.Remove bolt securing oil pump drive sprocket.
11.Remove crankshaft sprocket, oil pump drive
chain and sprocket.
12.Remove bolt and remove timing chain lubrication
jet.
Refit
13.Clean timing chain lubrication jet.
14.Fit lubrication jet and tighten bolt to10 Nm (7
lbf.ft).
15.Clean oil pump drive sprocket bolt threads.
16.Clean timing sprockets and chain guides.
17.Ensure that crankshaft is set to TDC firing No. 1
cylinder.
18.Fit oil pump drive chain to crankshaft sprocket
and fit sprocket to crankshaft.
19.Fit sprocket to oil pump.
20.Apply Loctite 242 to oil pump sprocket bolt
threads and tighten bolt to25 Nm (18 lbf.ft).
21.Fit timing chain fixed guide and tighten M10 bolt
to45 Nm (34 lbf.ft)and M6 bolt to10 Nm (7
lbf.ft).
22.Fit timing chain adjustable guide and tighten bolt
to25 Nm (18 lbf.ft).
ProCarManuals.com

12ENGINE
34
REPAIR
23.Fit camshaft sprocket to timing chain with timing
mark between the 2 bluelinks.
24.Fit timing chain to crankshaft sprocket aligning
blue link to timing mark.
25.Clean timing cover and mating face.
26.Apply an even film of sealant, Part No. STC
4600 to timing cover and spread to an even film
using a roller.
CAUTION: Assembly and bolt tightening
must be completed within 20 minutes of
applying sealant.
27.With assistance, fit timing cover, connect
vacuum pump drain hose and working
progressively, tighten bolts to27 Nm (20 lbf.ft).
28.Secure vacuum hose clip.
29.Fit cylinder head gasket.See this Section.
30.Fit sump gasket.See this Section.
31.Fit crankshaft front oil seal.See this Section.
ProCarManuals.com

12ENGINE
2
OVERHAUL GASKET - EXHAUST MANIFOLD
Service repair no - 30.15.12.01
Remove
NOTE: The following procedure covers
both EU3 and non EU3 engines
NOTE: EU3 engine illustrated.
1.Remove 3 bolts securing heater pipe to cylinder
head and turbocharger heat shield.
2.Remove heater pipe.
3.Remove bolt and remove turbocharger heat
shield.
4.Remove and discard 2 Allen screws securing
EGR pipe to exhaust manifold.
5.Remove banjo bolt securing oil feed pipe to
turbocharger and discard sealing washers.
6.Loosen turbocharger drain hose union at
cylinder block.
7.Remove 10 nuts and remove exhaust manifold
and turbocharger.
8.Remove manifold gasket.Refit
1.Clean exhaust manifold mating faces.
2.Position exhaust manifold to cylinder head using
new gasket and fit manifold nuts.
3.Working from the centre outwards, fit and tighten
nuts to25 Nm (18 lbf.ft).
4.Clean turbocharger drain and feed hose unions.
5.Fit turbocharger oil drain hose to cylinder block
and tighten union to48 Nm (35 lbf.ft).
6.Fit new sealing washers to turbocharger oil feed
pipe, fit banjo bolt and tighten to25 Nm (18
lbf.ft).
7.Position EGR pipe to exhaust manifold. Fit new
Allen screws and tighten to10 Nm (7 lbf.ft).
8.Position turbocharger heat shield.
9.Position heater pipe to cylinder head and tighten
bolts to25 Nm (18 lbf.ft).
10.Position exhaust manifold heatshield and tighten
M6 bolts to9 Nm (7 lbf.ft)and M8 bolt to25
Nm (18 lbf.ft).
ProCarManuals.com

12ENGINE
20
OVERHAUL GASKET - ENGINE SUMP
Service repair no - 12.60.38.01
Remove
1.Remove 2 bolts securing centrifuge oil drain pipe
to sump, remove and discard gasket.
2.Using sequence shown and noting their fitted
positions, remove 20 bolts securing sump to
cylinder block.
3.Remove sump, remove and discard gasket.
CAUTION: Do not lever between sump and
cylinder block.Refit
1.Clean sump and mating faces, ensure bolt holes
in cylinder block are clean and dry.
2.Using suitable solvent, remove all traces of
sealant from joint faces of timing chain cover and
crankshaft rear oil seal housing.
3.Clean centrifugal filter oil drain pipe and mating
faces.
4.Apply a bead of sealant, Part No. STC 3254 to
joint faces of timing chain cover and crankshaft
rear oil seal housing.
CAUTION: Assembly and bolt tightening
must be completed within 20 minutes of
applying sealant.
5.Position new sump gasket.
CAUTION: Gasket must be fitted dry.
6.Position sump, fit and lightly tighten bolts
ensuring they are in their original fitted positions.
ProCarManuals.com

ENGINE
21
OVERHAUL
7.Using sequence shown, tighten sump bolts to25
Nm (18 lbf.ft).
8.Fit new centrifuge oil drain pipe gasket.
CAUTION: Gasket must be fitted dry.
9.Fit centrifuge oil drain pipe, fit bolts and tighten
to10 Nm (7 lbf.ft).SEAL - CRANKSHAFT - REAR
Service repair no - 12.21.20.01
Remove
1.Remove flywheel.See Repair.
2.Remove sump gasket.See this Section.
3.Remove 5 bolts securing crankshaft rear oil seal
housing to cylinder block.
4.Remove and discard crankshaft rear oil seal and
housing.
NOTE: Dowel located.
ProCarManuals.com

19FUEL SYSTEM
4
REPAIR ELEMENT - FUEL FILTER
Service repair no - 19.25.07
Remove
1.Release fixings and remove battery cover.
2.Disconnect battery negative lead.
3.Raise rear of vehicle.
WARNING: Support on safety stands.
4.Release fixing and remove fuel filter cover.
5.Clean area around fuel filter.
6.Disconnect multiplug from filter element.
7.Remove fuel filter element.
Refit
8.Clean fuel filter and mating face.
9.Fit new fuel filter element and connect multiplug.
10.Position fuel filter cover and secure with fixing.
11.Remove stand(s) and lower vehicle.
12.Reconnect battery negative lead.
13.Fit and secure battery cover.COOLER - FUEL
Service repair no - 19.25.30
Remove
1.Remove 3 bolts and remove engine acoustic
cover.
2.Remove battery cover.
3.Disconnect battery negative lead.
4.Drain cooling system.See COOLING
SYSTEM, Adjustment.
5.Release 3 clips and disconnect 3 coolant hoses
from fuel cooler.
6.Release 2 fuel hoses from fuel cooler.
CAUTION: Plug the connections.
7.Release vacuum pipe clip from fuel cooler.
8.Remove 4 bolts securing fuel cooler to inlet
manifold and remove cooler.
Refit
9.Clean fuel hose connections.
10.Position fuel cooler to inlet manifold. Apply
Loctite 242 to bolts and tighten to18 Nm (13
lbf.ft).
11.Connect fuel hoses.
12.Connect coolant hoses, secure with clips.
13.Secure vacuum hose to fuel cooler.
14.Refill cooling system.See COOLING SYSTEM,
Adjustment.
15.Fit engine acoustic cover and secure with bolts.
16.Reconnect battery negative lead.
17.Fit battery cover.
ProCarManuals.com