transmission LAND ROVER DEFENDER 1999 Workshop Manual

01INTRODUCTION
10
INFORMATION CROSS REFERENCE OF EMISSION SYSTEM
TERMINOLOGY
NEW TERM (ACRONYM)
Accelerator pedal (AP).................................................
Air cleaner (ACL)..........................................................
Air conditioning (A/C)...................................................
Battery positive voltage (B+)........................................
Closed loop (CL)..........................................................
Closed throttle position (CTP)......................................
Canister purge valve (CANPV)....................................
Data link connector (DLC)...........................................
Diagnostic trouble code (DTC).....................................
Distributor ignition (DI).................................................
Engine control module (ECM)......................................
Engine coolant level (ECL)...........................................
Engine coolant temperature (ECT)..............................
Engine speed (RPM)....................................................
Evaporative emission system (EVAP)..........................
Engine fuel temperature sensor (EFTS)......................
4th gear, 3rd gear etc. (4GR, 3GR)..............................
Fuel pump (FP)............................................................
Fan control module (FCM)...........................................
Generator (GEN)..........................................................
Ground (GND)..............................................................
Heated oxygen sensor (H02S)....................................
Idle air control (IAC)......................................................
Idle air control valve (IACV).........................................
Ignition control module (ICM).......................................
Intake air temperature (IAT).........................................
Manifold vacuum zone (MVZ)......................................
Mass air flow sensor (MAF).........................................
Open loop (OL)............................................................
Relay module (RM)......................................................
Solid state relay module (SSRM).................................
Three way catalytic converter (TWC)..........................
Throttle body (TB)........................................................
Throttle position sensor (TP)........................................
Transmission range (TR)..............................................
Wide open throttle (WOT)............................................OLD TERM (ACRONYM)
Throttle pedal (-)..........................................................
Air cleaner (-)...............................................................
Air conditioning (AC)....................................................
Battery plus, bat +, bat feed (B+).................................
Closed loop (-).............................................................
Closed throttle, idle position (-)....................................
Charcoal canister purge valve (-).................................
Serial link (-)................................................................
Fault code (-)...............................................................
Electronic ignition (-)....................................................
Electronic control unit (ECU)........................................
Coolant level (-)...........................................................
Coolant temperature (temp).........................................
Coolant temperature thermistor (-)..............................
Engine speed (rev/min)................................................
Evaporative loss system (ELC)...................................
Fuel temperature thermistor (-)....................................
Fourth gear, 3rd gear (-)..............................................
Fuel pump (-)...............................................................
Condenser fan timer (-)................................................
Alternator (-)................................................................
Ground, earth (B-)........................................................
Lambda (02) sensor (-)................................................
Idle speed control (ISC)................................................
Stepper motor (-).........................................................
Ignition module (-)........................................................
Intake temperature/ambient temperature (-)................
Manifold depression, vacuum (-).................................
Air flow meter (-)..........................................................
Fault code display unit (-)............................................
Open loop (-)...............................................................
Relay (-).......................................................................
Control unit (-)..............................................................
Catalyst, catalytic converter (CAT)..............................
Throttle housing (-)......................................................
Transmission gear (-)...................................................
Full throttle, wide open throttle (WOT).........................
ProCarManuals.com

INTRODUCTION
11
INFORMATION VEHICLE IDENTIFICATION NUMBER (VIN)
The Vehicle Identification Number and the
recommended maximum vehicle weights are stamped
on a plate riveted to the brake pedal box in the engine
compartment. The VIN is also stamped on a plate
visible through the LH side of the windscreen.
a.Identification
b.Maximum permitted laden weight for vehicle
c.Maximum vehicle and trailer weight
d.Maximum road weight-front axle
e.Maximum road weight-rear axle
f.Paint code
g.Trim level
The number is also stamped on the RH side of the
chassis to the rear of the front lashing eye, see J6089.
The Vehicle Identification Number identifies the
manufacturer, model range, wheel base, body type,
engine, steering, transmission, model year and place
of manufacture. The following example shows the
coding process.
SAL LD H M 8 7 X A
SAL= World manufacturer identifier
LD= Land Rover Defender
H= 110 inch,V= 90inch,K= 130 inch
M= 4 door Station Wagon,A= 90 Soft Top, Hard Top,
Pick-up,B= 2 door Station Wagon,E= 2 door 130
Crew cab,F= 4 door 130 Crew cab,H= 130 High
Capacity Pick-up
8= Td5 engine.
7= RH drive, 5 speed manaul,8= LH drive, 5 speed
manual
X= 1999 MY, volume build.
A= Solihull build,F= CKD, assembled locally from kit
ProCarManuals.com

04 - GENERAL SPECIFICATION DATA
CONTENTS
Page
INFORMATION
ENGINE - Td5 1......................................................................................................
FUEL SYSTEM - Td5 3...........................................................................................
COOLING SYSTEM - Td5 3....................................................................................
CLUTCH - Td5 3.....................................................................................................
TRANSMISSION - Td5 4.........................................................................................
STEERING 5...........................................................................................................
SUSPENSION 6......................................................................................................
ROAD SPRING DATA 6..........................................................................................
SHOCK ABSORBERS 7.........................................................................................
BRAKES 7...............................................................................................................
AIR CONDITIONING 8............................................................................................
WIPER MOTORS 8.................................................................................................
ELECTRICAL 8.......................................................................................................
BULBS9 .................................................................................................................
VEHICLE WEIGHTS AND PAYLOAD 10................................................................
TOWING WEIGHTS 11...........................................................................................
OFF-ROAD PERFORMANCE 11............................................................................
TYRE SIZE AND PRESSURES 12.........................................................................
WHEELS 12............................................................................................................
VEHICLE DIMENSIONS 13....................................................................................
ProCarManuals.com

04GENERAL SPECIFICATION DATA
4
INFORMATION TRANSMISSION - Td5
Main gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward, 1 reverse, all synchromesh.............................................................................
Transfer box
Type LT230TE Two speed reduction on main gearbox output. Front.................................................................
and rear drive permanently engaged via a lockable
differential
Rear axle
Type Spiral bevel, fully floating shafts.................................................................................
Ratio 3.54:1.................................................................................
Front axle
Type Spiral bevel, enclosed constant velocity joints, fully.................................................................................
floating shafts, 32°angularity of universal joint on full
lock
Ratio 3.54:1.................................................................................
Propeller shafts
Type, front and rear Tubular 51 mm dia...........................................................
Universal joints Open type Hookes O3EHD.................................................................
ProCarManuals.com

10 - MAINTENANCE
CONTENTS
Page
MAINTENANCE
UNDERBONNET VIEW - Td5 1..............................................................................
SEATS AND SEAT BELTS 2..................................................................................
LAMPS, HORNS AND WARNING INDICATORS 2................................................
WIPERS AND WASHERS 3...................................................................................
HANDBRAKE 3.......................................................................................................
BATTERY CONDITION - Td5 4..............................................................................
HANDSET BATTERY 5...........................................................................................
HEADLAMP ALIGNMENT 5....................................................................................
ROAD WHEELS 6...................................................................................................
TYRE PRESSURES, CONDITION AND TREAD DEPTH 6....................................
BRAKE PADS, CALIPERS AND DISCS 7..............................................................
ROAD WHEEL SPEED SENSOR HARNESS - Td5 7............................................
FUEL FILTER ELEMENT 8.....................................................................................
FUEL FILTER SEDIMENTER - Td5 8.....................................................................
INTERCOOLER / COOLING SYSTEM 9................................................................
AMBIENT AIR PRESSURE (AAP) SENSOR - Td5 9..............................................
DOOR LOCKS AND HINGES 10............................................................................
ENGINE COOLANT 10...........................................................................................
BRAKE FLUID 11....................................................................................................
AIR FILTER ELEMENT AND DUMP VALVE 11.....................................................
AUXILIARY DRIVE BELT 12...................................................................................
PAS FLUID, CLUTCH FLUID AND SCREEN WASHER LEVELS 12.....................
STEERING BOX 13................................................................................................
ENGINE OIL 14.......................................................................................................
CENTRIFUGE ROTOR - Td5 14.............................................................................
FULL FLOW OIL FILTER 15...................................................................................
GEARBOX OIL 15...................................................................................................
TRANSFER BOX OIL 16.........................................................................................
FRONT AND REAR AXLE OIL 17..........................................................................
PROPELLER SHAFTS 18.......................................................................................
CLUTCH PIPES AND UNIONS 18..........................................................................
PAS PIPES AND UNIONS 19.................................................................................
ENGINE, GEARBOX, TRANSFER BOX AND AXLES 19.......................................
EXHAUST SYSTEM 20...........................................................................................
STEERING BOX AND SUSPENSION 20...............................................................
STEERING BALL JOINTS 21.................................................................................
SHOCK ABSORBERS 22.......................................................................................
TOWING BRACKET 22...........................................................................................
ENGINE AND TRANSMISSION MOUNTINGS 23..................................................
ProCarManuals.com

MAINTENANCE
23
MAINTENANCE ENGINE AND TRANSMISSION MOUNTINGS
1.Check condition of front LH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
2.Check condition of front RH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
3.Check condition of rear LH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
4.Check condition of rear RH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.ROAD TEST
There are two purposes for conducting a road test.
Firstly, to ensure the work completed within the
dealership meets the standards required as layed
down by dealership processes. Secondly, for a skilled
technician to assess the general condition of the
vehicle and report any conditions that the customer
should be made aware of.
CAUTION: Two wheel roller tests must not
be carried out. Four wheel roller tests
must be restricted to 3 mph (5 kph).
1.Check for correct operation of starter switch.
Ensure the engine starts in a correct manner.
Leave the engine running.
2.With vehicle stationary, turn steering from lock to
lock. Check for smooth operation and ensure
there is no undue noise from the power steering
pump or drive belt.
3.Depress clutch and select all gears in turn.
Check for smooth notch free engagement.
4.Drive vehicle on a short road test. Check all
vehicle systems for correct operation. Pay
particular attention to:
Engine noise
Gearbox noise
Suspension noise
Body noise
Braking system operation
Gear selection
Engine performance
5.Check for correct operation of all instruments
and warning devices where practical.
6.After road test, carry out a final inspection of the
vehicle on vehicle ramps.
7.Check all underbonnet fluid levels and top-up if
necessary.
ProCarManuals.com

18ENGINE MANAGEMENT SYSTEM
12
DESCRIPTION AND OPERATION SENSOR - CRANKSHAFT SPEED AND
POSITION (CKP)
The CKP sensor is located in the transmission housing with its tip adjacent to the outer circumference of the
flywheel. The CKP sensor works on the variable reluctance principal, which sends a signal back to the ECM in the
form of an ac voltage.
The ECM uses the signal from the CKP sensor for the following functions.
To calculate engine speed.
To determine engine crank position.
To determine fuel injection timing.
The CKP sensor works as a Variable Reluctance Sensor (VRS). It uses an electromagnet and a target ring to
generate a signal. As the target ring passes the tip of the CKP sensor the magnetic field produced by the sensor is
cut and then re-instated. The ECM measures the signal as an ac voltage.
The outer circumference of the flywheel acts as the target ring for the sensor. The flywheel is divided into 36
segments, each of 10°. 31 segments have drilled holes and 5 segments are spaces. This equals 360°or one
engine revolution. The 5 spaces correspond to the TDC position of the 5 cylinders. This allows the ECM to control
fuel injection timing for each of the cylinders.
Inputs / Outputs
The two pins of the CKP sensor (C1068-1 & C1068-2) are both outputs. The ECM (C0158-13 & C0158-36)
processes the outputs of the sensor. To protect the integrity of the CKP sensor signal, an earth screen is used.
The ECM measures the outputs from the CKP sensor. The ECM (C0158-13) measures a positive signal on a
pink/black wire, and a negative signal (C0158-36) on a white/blue wire. The earth path for the sensor is via the
ECM (C0158-16).
ProCarManuals.com

TRANSFER GEARBOX
5
REPAIR
43.If transfer gearbox is to be refitted, remove and
discard input shaft oil seal.
Refit
44.Clean mating faces of main gearbox extension
case and transfer gearbox.
45.Remove all traces of sealant from threads of
transfer gearbox securing bolts and studs.
46.Clean input shaft oil seal recess in transfer
gearbox.
47.Lubricate new input shaft oil seal with transfer
gearbox oil.
48.Using toolLRT-37-014, fit input shaft oil seal, lip
side facing inwards.49.Ensure guide studsLRT-41-009are fitted in
main gearbox extension case.
CAUTION: If securing studs were removed
during transfer gearbox removal, apply
Loctite 290 to threads of new studs; fit
studs and tighten to 45 Nm (33 lbf.ft).
50.Secure transfer gearbox to support plate
LRT-99-010, fit and tighten 4 bolts.
51.Raise transmission hoist until transfer gearbox
can be located over guide studsLRT-41-009.
52.Apply Loctite 290 to threads of securing bolts
and studs.
53.Fit and lightly tighten 2 nuts to secure transfer
gearbox to main gearbox extension case.
54.Remove guide studsLRT-41-009.
55.Ensuring bolts are in their original fitted
locations, fit and lightly tighten 4 bolts to secure
transfer gearbox to main gearbox extension
case.
56.Progressively tighten nuts and bolts to45 Nm
(33 lbf.ft).
57.Position earth leads to RH side of transfer
gearbox, fit and tighten bolt.
58.Connect low ratio detect switch multiplug and
secure to bracket. Connect Lucars to differential
lock warning lamp switch.
59.Raise gearbox jack and guide transfer gearbox
lever through tunnel.
60.Connect body harness clips to bracket on top of
transfer gearbox.
61.Position earth lead to transfer gearbox, tighten
nut to45 Nm (33 lbf.ft).
62.Connect speed sensor multiplug and secure
harness in clip.
63.Position heat shield to LH mounting, fit
mountings and brackets and tighten bolts to85
Nm (63 lbf.ft).
64.Fit nuts securing RH and LH mountings and
tighten to48 Nm (35 lbf.ft).
65.Position breather pipe to transfer gear box, fit
new sealing washers and tighten banjo bolts to
15 Nm (11 lbf.ft).
66.Remove bolts securing support plate to gearbox
jack.
67.Remove bolts securingLRT-99-010to transfer
gearbox.
68.Apply Loctite 290 to threads of bottom cover
securing bolts, fit bolts and tighten to25 Nm (18
lbf.ft)
69.Position differential lock control rod and secure
with retaining clip.
70.Clean rear propeller shaft to brake drum flange
mating faces.
ProCarManuals.com

41TRANSFER GEARBOX
6
REPAIR 71.Release propeller shaft, align flange markings
and connect to studs.
72.Fit nuts securing propeller shaft and tighten to48
Nm (33 lbf.ft).
73.Clean front propeller to transfer gearbox flange
mating faces.
74.Fit propeller shaft, align flange markings and
tighten nuts to48 Nm (33 lbf.ft).
75.Using new gasket, fit intermediate silencer and
tighten nuts to25 Nm (18 lbf.ft).
76.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair.
77.Refill transfer gearbox with recommended oil.
78.Fit cooling fan cowl.
79.Fit high/low operating rod and secure with
retaining clip.
80.Position handbrake outer cable to heelboard.
81.Position handbrake cable to lever, fit clevis pin,
washer and new split pin.
82.Position handbrake gaiter and secure with trim
studs.
83.Fit insulation pad to tunnel.
84.Fit gear lever cover.
85.Fit gear lever knobs.
86.Position diagnostic plug bracket, access panel
and tighten screws.
87.Fit carpet to transmission tunnel.
88.Fit cubby box.See CHASSIS AND BODY,
Repair.
89.Fit cooling fan.See COOLING SYSTEM,
Repair.
90.Reconnect battery negative lead.
91.Fit battery cover.GASKET - REAR COVER PLATE
Service repair no - 41.20.30
Remove
1.Raise vehicle on’4 post ramp’.
2.Mark rear cover plate to bearing housing for
assembly purposes.
3.Noting fitted position of stud bolt and harness
clip bracket, remove 5 bolts and stud bolt
securing cover plate.
4.Collect harness clip bracket.
5.Remove cover plate.
Refit
6.Clean cover plate and mating face.
7.Apply Hylosil RTV 102 to rear cover mating face.
8.Align reference marks, fit cover plate.
9.Clean cover bolts and apply Loctite 290 threads
of bolts and stud nut.
10.Position clip bracket, fit stud nut and bolts,
tighten by diagonal selection to25 Nm (18
lbf.ft).
11.Check/top-up transfer gearbox oil.
12.Lower vehicle.
ProCarManuals.com

86 - ELECTRICAL
CONTENTS
Page
DESCRIPTION AND OPERATION
SECURITY AND CENTRAL DOOR LOCKING 1....................................................
SECURITY AND CENTRAL DOOR LOCKING 2....................................................
ANTI-THEFT ALARM - FROM 02MY 3...................................................................
IMMOBILISATION SYSTEM - FROM 02MY 12......................................................
CENTRAL DOOR LOCKING (CDL) - FROM 02MY 15...........................................
ANTI-THEFT ALARM SYSTEM SELF TEST 17.....................................................
FASCIA CONSOLE 18............................................................................................
HEATED FRONT SCREEN - FROM 02MY 20.......................................................
HEATED FRONT SEATS - FROM 02MY 22..........................................................
ELECTRIC FRONT WINDOWS - FROM 02MY 24.................................................
PASSENGER COMPARTMENT FUSE BOX 26.....................................................
UNDER SEAT FUSE BOX 27.................................................................................
ADJUSTMENT
HEADLAMPS - ALIGN BEAM 1..............................................................................
SOLENOID/MOTOR - FRONT DOOR - ADJUST 1................................................
REPAIR
BELT - AUXILLARY DRIVE 1.................................................................................
HARNESS - INJECTORS 1....................................................................................
STARTER MOTOR 2..............................................................................................
CENTRE HIGH MOUNTED STOP LIGHT (CHMSL) - UP TO 02MY 2...................
ALTERNATOR 3.....................................................................................................
HORN - LH 4...........................................................................................................
HEADLAMP 5.........................................................................................................
LAMP - TAIL 6.........................................................................................................
RADIO6 ..................................................................................................................
SPEAKER - FRONT 7.............................................................................................
SWITCH - TRANSMISSION BRAKE 7...................................................................
LAMP - FRONT FLASHER 8..................................................................................
BATTERY - DISCONNECT - FROM 02MY 8..........................................................
MOTOR & REGULATOR - FRONT DOOR - FROM 02MY 9..................................
SWITCH - FASCIA - FROM 02MY 10.....................................................................
HARNESS - FRONT DOOR - FROM 02MY 10.......................................................
SOLENOID/MOTOR - TAIL DOOR - FROM 02MY 11............................................
SOLENOID/MOTOR - FRONT DOOR - FROM 02MY 12.......................................
SOLENOID/MOTOR - REAR DOOR - FROM 02MY 13.........................................
HARNESS - REAR DOOR - FROM 02MY 14.........................................................
REVERSE AND FOG GUARD LAMP - BULB 15....................................................
ProCarManuals.com