engine oil LAND ROVER DISCOVERY 1995 Service Repair Manual

INTRODUCTION
3
INFORMATION SYNTHETIC RUBBER
Many '0' ring seals, flexible pipes and other similar
items which appear to be natural rubber are made of
synthetic materials called Fluoroelastomers. Under
normal operating conditions this material is safe, and
does not present a health hazard. However, if the
material is damaged by fire or excessive heat, it can
break down and produce highly corrosive Hydrofluoric
acid which can cause serious burns on contact with
skin. Should the material be in a burnt or overheated
condition handle only with seamless industrial gloves.
Decontaminate and dispose of the gloves immediately
after use.
If skin contact does occur, remove any contaminated
clothing immediately and obtain medical assistance
without delay. In the meantime, wash the affected
area with copious amounts of cold water or limewater
for fifteen to sixty minutes.
RECOMMENDED SEALANTS
A number of branded products are recommended in
this manual for use during maintenance and repair
work.
These items include:
HYLOMAR GASKET AND JOINTING COMPOUND
and
HYLOSIL RTV SILICON COMPOUND.
They should be available locally from garage
equipment suppliers. If there is any problem obtaining
supplies, contact the following company for advice
and the address of the nearest supplier.
MARSTON LUBRICANTS LTD.
Hylo House,
Cale Lane,
New Springs,
Wigan WN2 1JR
Tel 01942 824242USED ENGINE OIL
WARNING: Prolonged and repeated
contact with engine or motor oil will result
in the removal of natural fats from the
skin, leading to dryness, irritation and dermatitis.
Used engine oil contains potentially harmful
contaminants which may cause skin cancer.
Adequate means of skin protection and washing
facilities should be provided.
Handling precautions
1.Avoid prolonged and repeated contact with oils,
particularly used engine oils.
2.Wear protective clothing, including impervious
gloves where applicable.
3.Do not put oily rags in pockets.
4.Avoid contaminating clothes, particularly
underwear, with oil.
5.Overalls must be cleaned regularly. Discard
unwashable clothing and oil impregnated
footwear.
6.First aid treatment must be obtained immediately
for open cuts and wounds.
7.Use barrier creams, before each work period, to
help the removal of oil from the skin.
8.Wash with soap and water to ensure all oil is
removed (skin cleansers and nail brushes will
help). Preparations containing lanolin replace the
natural skin oils which have been removed.
9.Do not use gasoline, kerosene, diesel fuel,
petrol, thinners or solvents for washing the skin.
10.If skin disorders develop, obtain medical advice.
11.Where practicable, degrease components prior
to handling.
12.Where there is a risk of eye contact, eye
protection should be worn, for example, goggles
or face shields; in addition an eye wash facility
should be provided.
Disposing of used oils
Environmental protection precaution
It is illegal to pour used oil onto the ground, down
sewers or drains, or into waterways.
Dispose of used oil through authorised waste disposal
contractors. If in doubt contact your Local Authority for
advice on disposal facilities.

01INTRODUCTION
4
INFORMATION ACCESSORIES AND CONVERSIONS
DO NOT FITunapproved accessories or conversions,
as they could affect the safety of the vehicle.
Land Rover will not accept liability for death, personal
injury, or damage to property which may occur as a
direct result of the fitting of non-approved conversions
to the vehicle.
WHEELS AND TYRES
WARNING: DO NOT replace the road
wheels with any type other than genuine
Land Rover wheels which are designed for
multi-purpose on and off road use and have very
important relationships with the proper operation
of the suspension system and vehicle handling.
Replacement tyres must be of the make and sizes
recommended for the vehicle, and all tyres must
be the same make, ply rating and tread pattern.
STEAM CLEANING
To prevent consequential rusting, any steam cleaning
within the engine bayMUSTbe followed by careful
re-waxing of the metallic components affected.
Particular attention must be given to the steering
column, engine water pipes, hose clips and ignition
coil clamp.
SPECIFICATION
The specification details and instructions set out in
this Manual apply only to a range of vehicles and not
to any one. For the specification of a particular vehicle
purchasers should consult their Dealer
The Manufacturer reserve the right to vary their
specifications with or without notice, and at such times
and in such manner as they think fit. Major as well as
minor changes may be involved in accordance with
the Manufacturer's policy of constant product
improvement.
Whilst every effort is made to ensure the accuracy of
the particulars contained in this Manual, neither the
Manufacturer or Dealer, by whom this Manual is
supplied, shall in any circumstances be held liable for
any inaccuracy or the consequences thereof.SPECIAL SERVICE TOOLS
The use of approved special service tools is
important. They are essential if service operations are
to be carried out efficiently, and safely. Where special
tools are specified,only these tools should be used
to avoid the possibility of personal injury or
damage to the components.Also the amount of time
which they save can be considerable.
Every special tool is designed with the close
co-operation of Land Rover, and no tool is put into
production which has not been tested and approved
by us. New tools are only introduced where an
operation cannot be satisfactorily carried out using
existing tools or standard equipment. The user is
therefore assured that the tool is necessary and that it
will perform accurately, efficiently and safely.
Special tools bulletins will be issued periodically giving
details of new tools as they are introduced.
All orders and enquiries from the United Kingdom
should be sent direct to V. L. Churchill. Overseas
orders should be placed with the local V. L. Churchill
distributor, where one exists. Countries where there is
no distributor may order direct from:
V. L. Churchill Limited,
PO Box 3,
Daventry, Northants,
England, NN11 4NF.
The tools recommended in this Workshop Manual are
listed in a multi-language illustrated catalogue,
obtainable from:
Messers. V. L. Churchill at the above address,
or from:
Land Rover Merchandising Service,
PO Box 534,
Erdington,
Birmingham, B24 0Q5,
COPYRIGHT
ÓLand Rover 1996
All rights reserved. No part of this publication may be
produced, stored in a retrieval system or transmitted
in any form, electronic, mechanical, recording or other
means without prior written permission of Land Rover.

04GENERAL SPECIFICATION DATA
2
INFORMATION Pistons
Clearance in bore, measured at bottom
of skirt at right angles to piston pin 0,018-0,041 mm...................................
Piston rings
Number of compression rings 2..........................................
Number of control rings 1....................................................
No 1 compression ring Molybdenum barrel faced.....................................................
No 2 compression ring Tapered and marked 'T' or 'TOP'.....................................................
Width of compression rings 1,478-1,49 mm..............................................
Compression ring gap 0,40-0,65 mm......................................................
Oil control ring width 3,0 mm.........................................................
Oil control ring rail gap 0,38-1,40 mm.....................................................
Camshaft
Location Central...........................................................................
Bearings Tin - aluminium...........................................................................
Number of bearings 5..........................................................
Drive Chain 9,52 mm pitch x 54 pitches..................................................................................
TappetsHydraulic-self-adjusting ...........................................................................
Valves
Length: Inlet 116,59-117,35 mm..................................
Exhaust 116,59-117,35 mm...........................
Seat angle: Inlet 45°to 45 1/2° ..................................
Exhaust 45°to 45 1/2° ...........................
Head diameter: Inlet 39,75-40,00 mm..................................
Exhaust 34,226-34,480 mm...........................
Stem diameter: Inlet 8,664-8,679 mm..................................
Exhaust 8,651-8,666 mm...........................
Stem to guide clearance: Inlet 0,025-0,066 mm..................................
Exhaust 0,038-0,078 mm...........................
Valve lift (Inlet and Exhaust) 9,49 mm............................................
Valve spring length fitted 40,4 mm at pressure of 29,5 kg..................................................
Lubrication
System type Wet sump, pressure fed.....................................................................
Oil pump type Eccentric rotor...................................................................
Oil pressure 2.75 bar (40 lb/in
2) at 2500 rev/min with engine at ......................................................................
running temperature
Oil filter-internal Wire screen, pump intake filter.................................................................
Oil filter-external Full flow, self-contained cartridge...............................................................

04GENERAL SPECIFICATION DATA
4
INFORMATION Piston rings
Number of compression rings 2..........................................
Number of control rings 1....................................................
No 1 compression ring Nitrided steel barrel faced.....................................................
No 2 compression ring Tapered spherical barrel marked 'TOP'.....................................................
Width of compression rings 1.478 - 1.49 mm.............................................. 0.0582 - 0.0587 in
(Top) 1.21 - 1.23 mm................................ 0.0476 - 0.0484 in
Compression ring gap 0.40-0.65 mm...................................................... 0.0157 - 0.0256 in
(Top) 0.3 - 0.5 mm................................ 0.0118 - 0.0197 in
Oil control ring type Aclonoform..........................................................
Oil control ring width 3.0 mm......................................................... 0.1181 in
Oil control ring rail gap 0.38-1.40 mm..................................................... 0.0150 - 0.0551 in
Camshaft
Location Central...........................................................................
Bearings Non serviceable...........................................................................
Number of bearings 5..........................................................
Drive Chain 9.52 mm pitch x 54 pitches..................................................................................
Camshaft End Float 0.076 - 0.355 mm......................................................... 0.003 - 0.014 in
TappetsHydraulic self-adjusting ...........................................................................
Valves
Length: Inlet 116.59 - 117.35 mm.................................. 4.590 - 4.620 in
Exhaust 116.59 - 117.35 mm........................... 4.590 - 4.620 in
Seat angle: Inlet 46°-46°25' ..................................
Exhaust 46°-46°25' ...........................
Head diameter: Inlet 39.75 - 40.00 mm.................................. 1.565 - 1.575 in
Exhaust 34.227 - 34.48 mm........................... 1.3475 - 1.3575 in
Stem diameter: Inlet 8.664 - 8.679 mm.................................. 0.3411 - 0.3417 in
Exhaust 8.651 - 8.666 mm........................... 0.3406 - 0.3412 in
Stem to guide clearance: Inlet 0.025 - 0.066 mm.................................. 0.0010 - 0.0026 in
Exhaust 0.038 - 0.078 mm........................... 0.0015 - 0.0031 in
Valve lift (Inlet and Exhaust) 9.94 mm............................................ 0.3913 in
Valve spring length fitted 40.4 mm (1.59 in) at pressure of 29.5 kg (65 lb)..................................................
Lubrication
System type Wet sump, pressure fed.....................................................................
Oil pump type Rotor...................................................................
Oil pressure 2.11 to 2.81 kg/cm
2(30 to 40 psi) at 2400 rev/min with ......................................................................
engine warm
Oil filter-internal Wire screen, pump intake filter in sump................................................................
Oil filter-external Full flow, self-contained cartridge...............................................................

04GENERAL SPECIFICATION DATA
6
INFORMATION FUEL SYSTEM (GEMS) 4.0 V8 ENGINE
Type Sagem - Lucas Gems 8 hot wire system electronically.................................................................................
controlled
Fuel pump-make/type High pressure electrical, immersed in the fuel tank......................................................
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Mass airflow sensor
Make and type Lucas 'Hot Wire' 20AM.................................................................
Injectors
Make and type Lucas D1000.................................................................
Electronic Control Module
Make and type Lucas GEMS 8.3.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Coolant temperature sensor
Make and type Lucas 8TT.................................................................
Bypass Air valve (Stepper motor)
Make and type Lucas 3ACM.................................................................
Throttle position sensor
Make and type Lucas 3TP.................................................................
Heated oxygen sensor - catalyst vehicles
Make and type Lucas 4LS.................................................................
Camshaft position sensor
Make and Land Rover part no. Lucas ERR6170.........................................
Crankshaft position sensor
Make and type Lucas 3VRS, Honeywell ERR6049.................................................................
Knock sensor
Make and type Lucas 2KS.................................................................
Intake air temperature sensor
Make and type Lucas 10TT.................................................................
Ignition coils
Make and type Lucas 2DIS2.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................

04GENERAL SPECIFICATION DATA
18
INFORMATION 300 Tdi ENGINE
Type Direct injection, turbocharged, intercooled.................................................................................
Number of cylinders 4.........................................................
Bore 90,47 mm.................................................................................
Stroke 97,00 mm...............................................................................
Capacity 2495 cc...........................................................................
Compression ratio 19.5:1±0.5:1 ............................................................
Valve operation O.H.V. pushrod operated................................................................
Crankshaft
Main bearing journal diameter 63,475 - 63,487 mm..........................................
Regrind dimensions 63,2333 - 63,246 mm.........................................................
Use 0.010 in U/S bearings
Crankpin journal diameter 58,725 - 58,744 mm................................................
Regrind dimensions 58,4708 - 58,48985 mm.........................................................
Use 0.010 in U/S bearings
Crankshaft end thrust Taken on thrust washers at centre main bearing.......................................................
Crankshaft end float 0,05 - 0,15 mm.........................................................
Main bearings
Number and type 5 halved shells with oil grooves..............................................................
Diametrical clearance 0,0792 - 0,0307 mm.......................................................
Connecting rods
Length between centres 175,38 - 175,43 mm...................................................
Diametrical clearance (big-end bearings) 0,025 - 0,075 mm........................
End float on crankpin 0,15 - 0,356 mm.......................................................
Pistons
Type Aluminium alloy, combustion chamber in crown..................................................................................
Graphite coating on sidewalls.
Skirt diametrical clearance
(at right angle to gudgeon pin) 0,025 - 0,05 mm.........................................
Maximum height above combustion face 0,8 mm.........................
Gudgeon pins
Type Floating.................................................................................
Fit in piston Hand push fit.......................................................................
Diameter 30,1564 - 30,1625 mm..........................................................................
Clearance in connecting rod 0,0025 - 0,0163 mm............................................

04GENERAL SPECIFICATION DATA
20
INFORMATION Lubrication
System Wet sump, pressure fed.............................................................................
Pressure, engine warm at normal operating speeds 25 - 55lbf/in
2= 1,76 - 3,87Kgf cm2........
Oil pump:
- Type G-rotor integral with front cover.......................................................................
- Drive off crankshaft nose.....................................................................
Oil pressure relief valve Non-adjustable....................................................
Relief valve spring:
- Full length 51,6mm......................................................................
- Compressed length at 7.71Kg load 31mm................................
Oil filter Screw-on disposable canister.............................................................................
Engine oil cooler Combined with coolant radiator and intercooler...............................................................
FUEL SYSTEM - 300 Tdi
Fuel lift pump type Mechanical with hand primer............................................................
Fuel lift pump pressure 42 - 55 kpa at 1800 rpm.....................................................
Fuel filter Paper element in disposable canister..........................................................................
Air cleaner Paper element type........................................................................
COOLING SYSTEM - 300 Tdi
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler and
turbo intercooler.
Cooling fan 11 blade axial flow 433 mm diameter. 1.29:1 drive.......................................................................
ratio. Viscous coupling.
Pump type Centrifugal, impellor, belt driven.........................................................................
Thermostat opening 88° .........................................................
Expansion tank cap pressure 15lbf/in
2= 1,06Kgf cm2(system pressure) ...........................................
CLUTCH - 300 Tdi
Type Valeo diaphragm spring.................................................................................
Centre plate diameter 235 mm.......................................................
Facing material Verto F202 grooved.................................................................
Release bearing Ball journal...............................................................

04GENERAL SPECIFICATION DATA
22
INFORMATION ENGINE - Mpi - 2.0 LITRE
Type 20 T4 - 16 valve twin overhead camshaft.................................................................................
Cylinder arrangement 4 in line.......................................................
Bore 84.45 mm.................................................................................
3.325 in
Stroke 89.00 mm...............................................................................
3.504 in
Capacity 1994 cm
3...........................................................................
121.68 in3
Firing order 1-3-4-2.......................................................................
Compression ratio 10 : 1............................................................
Oil pump
Outer rotor to body clearance 0.05 to 0.10 mm..........................................
Inner rotor tip clearance 0.025 to 0.12 mm...................................................
Outer rotor end float 0.03 to 0.08 mm.........................................................
Oil pressure relief valve
Spring free length 42.0 mm.............................................................
Cooling system
Starts to open 82 to 86°C ...................................................................
Thermostat fully open 88°C .......................................................
Open travel A 9 mm...................................................................
Camshaft
Camshaft end-float 0.06 to 0.25 mm...........................................................
Bearing clearance 0.060 to 0.094 mm............................................................
Service limit 0.15 mm.............................................................
Timing belt tensioner
Spring free length 57.5 to 58.5 mm.............................................................
Cylinder head
Longitudinal warp - maximum 0.1 mm.................................
Transverse warp - maximum 0.1 mm...................................
Diagonal warp - maximum 0.1 mm......................................
Cylinder head height 135.0 to 135.1 mm...............................................
Valve springs
Free length 46.25 mm.......................................................................
Fitted length 37.0 mm.....................................................................
Load at fitted length 255±12 N ..........................................................
Load at valve open length 560±22.5 N ................................................

ENGINE TUNING DATA
1
INFORMATION ENGINE 3.9 V8i
Type3.9 Litre V8i .................................................................................
Firing order1-8-4-3-6-5-7-2 .....................................................................
Cylinder Numbers
Left bank 1-3-5-7..........................................................................
Right bank 2-4-6-8........................................................................
No 1 Cylinder locationPulley end of left bank ...................................................
Timing marksOn crankshaft vibration damper ..................................................................
Spark plugs
Make/type(8.13:1 Compression) Champion RN11YCC......................................
Gap 0.84-0.96mm..................................................................................
Make/type(9.35:1 Compression) Champion RN11YCC......................................
Gap 0.84-0.96mm..................................................................................
Coil
Make/type Bosch 0-221-122-392,........................................................................
Compression ratio8.13:1 or 9.35:1 .........................................................
Fuel injection systemLucas 14 CUX Hot-wire air flow sensor system .....................................................
electronically controlled
Valve Timing Inlet Exhaust
Opens 32°BTDC .............................................................................. 70°BBDC
Closes 73°ABDC .............................................................................. 35°ATDC
Duration 285° ........................................................................... 285°
Valve peak 104°ATDC ....................................................................... 114°BTDC
Idle speed - controlled by MFI system
- all loads off in neutral 665 to 735 rev/min.....................................................
- auto gearbox in gear, air con operating 650±28 rev/min .........................
- auto gearbox in gear, air con off 600±28 rev/min ....................................
- manual gearbox 700±28 rev/min .............................................................
- manual gearbox, air con operating 750±28 rev/min ................................
Base idle speed525±25 rev/min
See FUEL SYSTEM, Fault..............................................................
diagnosis, Base idle speed setting.
Ignition Timing - dynamic at 800 rev/min max,
vacuum disconnected
8.13:1 compression, non catalyst 2°BTDC±1° .....................................
9.35:1 compression, non catalyst 4°BTDC±1° .....................................
9.35:1 compression, catalyst 5°BTDC±1° ............................................
Exhaust gas
CO content at idle 0.5 to 1.0% max.............................................................

ENGINE TUNING DATA
3
INFORMATION ENGINE 4.0 V8
Type4.0 Litre V8 .................................................................................
Firing order1-8-4-3-6-5-7-2 .....................................................................
Cylinder Numbers
Left bank 1-3-5-7..........................................................................
Right bank 2-4-6-8........................................................................
No 1 Cylinder locationPulley end of left bank ...................................................
Spark plugs
Make/type Champion RN11YCC........................................................................
Gap 0.90 - 1.00 mm.................................................................................. 0.035 - 0.040 in
Coils
Make Lucas 2D1S2................................................................................
Type Twin coils, bank of 4.................................................................................
High Compression Low Compression
Compression ratio 9.35:1............................................................ 8.2:1
Fuel injection systemSagem - Lucas GEMS8 Hot-wire air flow sensor .....................................................
system electronically controlled
Valve Timing Inlet Exhaust
Opens 28°BTDC .............................................................................. 66°BBDC
Closes 77°ABDC .............................................................................. 39°ATDC
Duration 285° ........................................................................... 285°
Valve peak 108°ATDC ....................................................................... 110°BTDC
Idle speed - controlled by GEMS system
all loads off 700±20 rev/min ..............................................................
Base idle speedNot adjustable ..............................................................
Idle air control valve position, checked viaTestBook
CO at idle
vehicles without heated oxygen sensors 1.5% ñ 0.5%.................
Fuel
9.35:1 catalyst 95 RON minimum unleaded.................................................................
USA vehicles - Premium unleaded (PUG) 95 RON minimum.......................
8.2:1 catalyst 91 RON minimum unleaded.................................................................
Non catalyst 91 RON minimum unleaded or leaded.........................................................