inflation pressure LAND ROVER DISCOVERY 1995 Service Repair Manual

74WHEELS AND TYRES
2
FAULT DIAGNOSIS FAULT - SYMPTOMS
Vibration through steering wheel
1.Check tyre pressures.
See Repair, Tyre
Pressures
2.Check condition of tyres.See Tyre Wear Chart
3.Check front wheel alignment.See STEERING,
Adjustment, Front Wheel Alignment
4.Check wheel balance.See Repair, Wheel
Balancing
NOTE: In the event that any apparent
vibration is not eliminated at this stage.
See PROPELLER SHAFTS, Fault
diagnosis, Vibration Harshness
NOTE: In the event that any apparent
vibration is not eliminated at this stage, go
to steering Fault Diagnosis, Fault -
Symptom (Steering vibration, road wheel
shimmy/wobble).
See STEERING, Fault diagnosis,
Steering Faults
NOTE: Radial ply tyres have a flexible
sidewall, which produces a sidewall bulge
making the tyre appear under-inflated.
This is a normal condition for radial ply tyres. Do
not attempt to reduce this bulge by over-inflating
the tyre.
1. Correct inflation.
2. Under-inflation.
3. Over-inflation.
4. Tread contact with road.

WHEELS AND TYRES
1
REPAIR GENERAL INFORMATION
WARNING: This is a multi- purpose vehicle
with wheels and tyres designed for both
on and off road usage. Only use wheels
and tyres specified for use on the vehicle.
The vehicle is equipped with tubeless 'S','T' or 'H'
rated radial ply tyres as standard equipment. The
tyres are of European metric size and must not be
confused with the "P" size metric tyres available in
North America.
Vehicle wheel sets, including spare wheel, must be
fitted with the same make and type of tyre to the
correct specification and tread pattern. Under no
circumstances must cross-ply or bias-belted tyres be
used.
For tyre specification and pressures.
See GENERAL
SPECIFICATION DATA, Information, Wheels and
Tyres
Alloy Wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter cast aluminium alloy wheels.The
surface has a paint finish covered with a clear
polyurethane lacquer. Care must be taken when
handling the wheel to avoid scratching or chipping the
finish.
The alloy wheel rim is of the asymmetric hump
type incorporating a safety hump to improve
location of the tyre bead in its seat. If difficulty is
experienced in fitting tyres to this type of rim.
See
Tyre Fitting
WARNING: Do not fit an inner tube to an
alloy wheel.
Steel wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter steel wheels.TYRE INSPECTION
Inspect tyres at weekly intervals to obtain maximum
tyre life and performance and to ensure compliance
with legal requirements. Check for signs of incorrect
inflation and uneven wear, which may indicate a need
for balancing or front wheel alignment.
See Fault
diagnosis, Tyre Wear Chart
if the tyres have
abnormal or uneven wear patterns.
Check tyres at least weekly for cuts, abrasions, bulges
and for objects embedded in the tread. More frequent
inspections are recommended when the vehicle is
regularly used in off road conditions.
To assist tyre inspection, tread wear indicators are
moulded into the bottom of the tread grooves, as
shown in the illustration below.
When the tread has worn to a remaining depth of 1.6
mm the indicators appear at the surface as bars which
connect the tread pattern across the width of the tread
as shown in the illustration below.

74WHEELS AND TYRES
2
REPAIR When the indicators appear in two or more adjacent
grooves, at three locations around the tyre, a new tyre
must be fitted.
NOTE: Do not attempt to interchange
tyres, e.g. from front to rear, as tyre wear
produces characteristic patterns
depending on their position. If tyre position is
changed after wear has occured, the performance
of the tyre will be adversely affected.
NOTE: Territorial vehicle regulations
governing tyre wear MUST be adhered to.
WHEELS INSPECTION
Regularly check the condition of the wheels. Replace
any wheel that is bent, cracked, dented or has
excessive runout.
VALVES INSPECTION
Check condition of inflation valve. Replace any valve
that is worn, cracked, loose, or leaking air.TYRE PRESSURES
Maximum tyre life and performance will be
obtained only if tyres are maintained at the correct
pressures.
Tyre pressures must be checked at least once a
month and at least once a week, preferably daily, if
the vehicle is used off road.
The tyre inflation pressure is calculated to give the
vehicle satisfactory ride and steering characteristics
without compromising tyre tread life. For
recommended tyre pressures in all conditions.
See
GENERAL SPECIFICATION DATA, Information,
Wheels and Tyres
American vehicles - A label attached to the inside
edge of the driver's door also provides tyre pressure
information.
Always check tyre inflation pressures using an
accurate gauge and inflate tyres to the
recommended pressures only.
Check and adjust tyre pressuresONLYwhen the
tyres are cold, vehicle parked for three hours or more,
or driven for less than 3.2 km (2 miles) at speeds
below 64 km/h (40 mph). Do not reduce inflation
pressures if the tyres are hot or the vehicle has been
driven for more than 3.2 km (2 miles) at speeds over
64 km/h (40 mph), as pressures can increase by 0.41
bars (6 p.s.i) over cold inflation pressures.
CheckALLtyre pressures including the spare. Refit
the valve caps as they form a positive seal and keep
dust out of the valve.

WHEELS AND TYRES
5
REPAIR Off vehicle balancing
Balance wheel assembly referring to equipment
manufacturer's instructions.
It is essential that the wheel is located by the centre
holeNOTthe stud holes. To ensure positive wheel
location the diameter of the locating collar on the
machine shaft must be 112.80 to 112.85 mm (4.441 to
4.443 in). This diameter will ensure that the collar fits
correctly within the centre hole of the wheel.
Where possible always use the vehicle wheel
retaining nuts to locate the wheel on the balancer, to
avoid damaging the wheel. If this is not possible, the
locating nuts must be of a similar pattern to the
original wheel nuts. The use of conical type wheel
nuts for this purpose may damage the aluminium
alloy.
Cleaning
Wash the aluminium wheels using a suitable wash
and wax concentrate correctly diluted and rinse with
cold clear water.DO NOTuse abrasives or aluminium
wheel cleaners containing acid, as they will destroy
the lacquer finish.
Tyre changing
Use only tyre changing equipment to mount or
demount tyres, following the equipment
manufacturer's instructions.DO NOTuse hand tools
or tyre levers, as they may damage tyre beads or the
aluminium wheel rim.
Puncture repair
Remove punctured tyre from wheel and repair using a
combination service plug and vulcanising patch.
Always follow manufacturer's instructions when using
a puncture repair kit.
Only punctures in tread area are repairable,DO NOT
attempt to repair punctures in tyre shoulders or
sidewalls.
Do not attempt to repair a tyre that has sustained the
following: bulges or blisters, ply separation, broken or
cracked beads, wear indicators visible and punctures
larger than 6 mm diameter.
CAUTION: Do not use tyre sealants that
are injected through valve stem to repair
punctured tyres, they may produce wheel
corrosion and tyre imbalance.
Aluminium wheel rim bead seats should be cleaned
using a non-abrasive cleaner to remove the mounting
lubricants and old rubber. Before mounting or
demounting a tyre, bead area should be well
lubricated with a suitable tyre lubricant.
TYRE FITTING
Alloy wheels
1.Install a new valve assembly.
2.Ensure wheel and tyre is adequately lubricated.
3.Mount tyre in normal manner. Inflate tyre and at
same time apply hand pressure to area around
valve to aid seating over valve first.
NOTE: Stop inflation immediately if tyre
seats opposite valve, as this will result in
valve being blocked by tyre beading,
making further inflation impossible, and carry out
following procedure.
4.Deflate tyre, unseat and rotate it around the rim
until valve is in line with that part of tyre which
seated initially. This part of beading having
seated over hump previously will automatically
seat first when tyre is re-inflated.
5.Inflate tyre to seat beads correctly, finally inflate
to correct pressure.