horn LAND ROVER DISCOVERY 1995 User Guide

ELECTRICAL
11
DESCRIPTION AND OPERATION ANTI-THEFT ALARM BUILT-IN TEST (96 MODELS)
NOTE: The handset should be detached
from the key to allow perimetric testing of
the alarm system. The system will
automatically switch to volumetric testing if the
handset is in close proximity to the starter switch.
The built-in test procedure can be accessed providing
the following conditions exist:
Alarm disarmed.
Ignition off.
Doors unlocked.
Bonnet[hood] closed.
The test mode can be entered by completing the
following instructions within 5 seconds:
1.Open bonnet.
2.Turn starter switch on.
3.Open driver's door (far enough to activate
switch).
4.Turn starter switch off.
5.Turn starter switch on.
If the test mode has been correctly accessed, the
sounder/horn will operate briefly and the anti-theft
alarm indicator and hazard warning lights will flash.
Perimetric tests
The anti-theft alarm indicator light and the hazard
warning lights will flash when:
1.Door switches are activated;
2.The bonnet is opened;
3.Sill switches are activated;
4.Key switches are activated.
NOTE: Operation of key switches can be
verified by turning the key in the relevent
direction so as not to simultaneously
activate the sill switch. If the key switch changes
state, the change should be detected but the sill
switch will not be activated.
Volumetric tests
Press the unlock button or move the handset close to
the starter switch to disable perimetric testing and
enable volumetric testing. If movement is detected
within the vehicle by the ultrasonic sensor it will be
indicated by flashing the anti-theft alarm indicator and
hazard warning lights.
NOTE: Exit anti-theft alarm built-in test by
turning starter switch to the off position.

86ELECTRICAL
2
REPAIR FUSE BOX - ENGINE COMPARTMENT
The fusebox is located on the right side of the engine compartment. The circuits protected and their locations are
shown on the inside of the fusebox cover. To change a main circuit fuse prise off protective cover A and remove
retaining screws.
Fuses
1. Heated rear window
2. Sidelights
3. Air conditioning
4. Hazard warning lights, horn
5. ABS valve
6. Fuel pump
7. Fuel injectors
A Main circuit fuses
8. ABS pump
9. Ignition circuits
10. Lighting
11. Window lift, central door locking, rear blower
12. Heater, air conditioning
13. Generator

ELECTRICAL
11
REPAIR HANDSET INITIALISATION
NOTE: New handsets are supplied in pairs.
If a new handset is required, it will require
initialisation to the ECU using the
following procedure:
1.Starting conditions: ignition off, doors unlocked,
bonnet switch depressed.
2.Carry out instructions 3. to 9. within 8 seconds.
3.Switch ignition ON.
4.Switch ignition OFF.
5.Lock doors.
6.Unlock doors.
7.Release bonnet switch.
8.Switch ignition ON.
9.Switch ignition OFF.
If alarm is correctly accessed, horn will sound and
LED will light. It is now possible to programme two
handsets of correct frequency to vehicle alarm ECU.
This must be carried out within two minutes.
10.Press and hold down button on first handset until
dash LED flashes.
11.Repeat instruction 10. for second handset.
12.The LED will extinguish if both handsets have
been initialised correctly.CENTRAL DOOR LOCKING
Where electrically operated central door locking is
fitted, locking or unlocking the drivers door from
outside by key operation, or from the inside with the
sill knob automatically locks or unlocks the passenger
and rear doors.
Front and rear passenger doors can be independently
locked or unlocked from inside the vehicle by sill knob
operation but can be overidden by further operation of
the driver's door locking control.
On rear doors, where side facing fold down seats are
fitted, a child safety lock is provided which can be
mechanically pre-set to render the interior door
handles inoperative.
Failure of a door actuator will not affect the operation
of the remaining doors and the door with the
inoperative actuator can still be locked or unlocked
manually.
The actuator unit fitted to the driver's door is the
master actuator and is identified from the actuators
fitted to the passenger and rear doors by having a
white connecting link, whereas the passenger and
rear door actuators have grey coloured connecting
links.
NOTE: Actuator units are non-servicable, if
a fault should occur replace the unit with a
new one.