key LAND ROVER DISCOVERY 1995 User Guide

12ENGINE
8
REPAIR
9.Disconnect multiplug from camshaft sensor.
See FUEL SYSTEM SFI, Repair, Camshaft
Position Sensor (CMP Sensor)
10.Remove 9 bolts securing front cover.
11.Remove 2 bolts securing sump to front cover.
12.Loosen 4 bolts securing sump adjacent to front
cover (2 each side).
13.Release front cover assembly.
14.Remove oil seal.
15.Remove and discard gasket.Refit
16.Clean sealant from threads of cover bolts.
17.Clean old sealant from front cover and block joint
face.
CAUTION: Use a plastic scraper.
18.Apply Hylosil jointing compound to gasket
position on cover and block.
19.Fit new gasket to block face.
20.Ensure oil seal register in cover is clean.
21.Lubricate outer face of NEW oil seal.
22.Using LRT-12-089, fit seal to cover.
23.Lubricate oil pump drive gear and position in
pump with groove away from engine.
24.Locate alignment tool LRT-12-090 on front cover
and oil pump drive gear.
25.Position front cover over crankshaft.
26.Press and rotate tool to engage drive gear until
drive gear keyway aligns with Woodruff key.
27.Fit cover to cylinder block.

12ENGINE
2
DESCRIPTION AND OPERATION The aluminium alloy, tin coated pistons have two
compression and an oil control ring and are secured
to the connecting rods by semi-floating gudgeon pins
which are an interference fit in the small-end bush.
Gudgeon pins are offset towards the thrust side of the
pistons to reduce frictional drag.
Plain, big-end bearing shells are fitted to each
connecting rod.The internally toothed timing belt is driven from a gear
which is keyed to the crankshaft, belt tension being
controlled by a semi-automatic tensioner.
The trochoidal type oil pump is mounted on the front
of the engine and carries the crankshaft front oil seal.
Drive to the pump is via a Woodruff key inserted in the
crankshaft.

12ENGINE
4
DESCRIPTION AND OPERATION CYLINDER BLOCK COMPONENTS
1. Cylinder block
2. Knock sensor
3. Crankshaft sensor
4. Bolt - crankshaft sensor
5. Locating dowel - cylinder head
6. Bolt - connecting rod
7. Piston
8. Piston ring - top compression
9. Piston ring - 2nd compression
10. Piston ring - oil control
11. Gearbox adapter plate
12. Bearing shell - big end - upper
13. Flywheel
14. Bolt - flywheel
15. Torx screw - gearbox adapter plate
16. Blanking plate
17. Bolt - blanking plate
18. Gasket
19. Bolt - crankshaft rear oil seal housing
20. Crankshaft rear oil seal and housing
21. Bolt - coolant pump cover
22. Coolant pump cover
23. Impeller
24. Sealing rings
25. 'O' ring
26. Bolts - coolant pump
27. 'O' ring
28. Coolant pump body
29. Thrust washer halves - upper
30. Bearing shell - main bearing - upper
31. Locating dowel - oil pump
32. Locating dowel - flywheel
33. Gudgeon pin34. Crankshaft
35. Bearing shell - big end - lower
36. Bearing cap - big end
37. Nut - big end bearing cap
38. Locating dowel - main bearing cap
39. Bearing caps - main bearings
40. Bolt - main bearing cap
41. Thrust washer halves - lower
42. Bearing shell - main bearing - lower
43. Woodruff keys
44. Dipstick
45. Bolt - dipstick tube
46. Dipstick tube
47. Bolts - sump
48. Gasket - sump
49. 'O' ring
50. Oil strainer
51. Bolts - oil strainer
52. Sump
53. Washer - drain plug
54. Drain plug
55. Oil filter element
56. Crankshaft front oil seal
57. Bolts - oil pump
58. Gasket - oil pump
59. Oil pump
60. Oil pressure switch
61. Crankshaft spigot bush
62. Crankshaft spigot bearing
63. Locating dowel - coolant pump
64. Connecting rod
65. Bolts belt tensioner mounting plate
66. Belt tensioner mounting plate
67. Bolt - gearbox adapter plate

12ENGINE
4
REPAIR CRANKSHAFT FRONT OIL SEAL
Service repair no - 12.21.14
Remove
1.Remove timing belt.
See Camshaft Drive Belt
2.Slide timing gear off crankshaft and remove
drive key.
3.Ensure bore of tool is burr free, fit and tighten
tool LRT-12-073 into crankshaft front oil seal.
4.Using thrustpad, tighten centre screw of tool to
remove oil seal.
5.Remove thrust button from crankshaft.
Refit
1.Use lint free cloth and thoroughly clean seal
recess and running surface on crankshaft. Clean
crankshaft gear and pulley.
2.Lubricate oil seal sealing surfaces with engine
oil.
3.Fit tool LRT-12-070 onto crankshaft.
4.Position new oil seal on crankshaft, drift into
place using LRT-12-069 and remove protector.
5.Fit drive key to crankshaft and slide timing gear
onto crankshaft.
6.Fit and tension timing belt.
See Camshaft
Drive Belt

19FUEL SYSTEM
10
REPAIR
KEY
1. Spherical bush/housing
2. Retaining clips (2)
3. Countershaft assembly
4. Overtravel spring
5. Throttle shaft nut
6. Throttle return spring (2)
7. Tab washer
8. Throttle stop lever
9. Throttle bracket assembly
10. Pop rivets (2)

19FUEL SYSTEM
18
REPAIR FUEL PIPES
Service repair no - 19.40.92
WARNING: Depressurise fuel system.See
Depressurise Fuel System
before
disconnecting any fuel pipes ensure that
all necessary precautions are taken against fuel
spillage
WARNING: Ensure fuel handling
precautions given in Section 01 -
introduction are strictly adhered to when
carrying out following instructions.
KEY
1. Fuel feed hose to fuel rail.
2. Fuel return hose to fuel tank.
3. Rigid fuel feed pipe.
4. Rigid fuel return pipe.
5. Fuel filter.6. Rigid fuel feed pipe to filter.
7. Breather hose.
8. In-tank fuel pump.
9. Fuel filler neck.
10. Fuel tank.

SFI
7
DESCRIPTION AND OPERATION REV: 09/95 Fuel pressure regulator
The fuel pressure regulator is located at the rear of
the engine in the fuel rail. It consists of a fuel inlet,
outlet, vacuum port and internal diaphragm.
When the engine is under high manifold depression,
the applied vacuum sucks the diaphragm of its seat,
allowing fuel to return to the tank, resulting in a lower
fuel pressure. This is necessary because the high
depression will try to suck the fuel from the injector,
resulting in overfuelling if the pressure remained
constant. Failure will result in a rich mixture at idle but
normal at full load, or a rich mixture resulting in engine
flooding, or a weak mixture. Although the fault will not
illuminate the MIL, faults caused by the failure may be
indicated.Relay module
The engine management system employs a relay
module, which houses the main relay and the fuel
pump relay.
Main relay
The main relay supplies the power feed to the ECM
with a tap off to feed the fuel injectors (8 amps) and
air flow sensor (4 amps). This relay is controlled by
the engine management ECM. This enables the ECM
to remain powered up after ignition is switched off.
During this 'ECM power down routine' the ECM
records all temperature readings and powers the
stepper motor to the fully open position. Failure of this
relay will result in the engine management ECM not
being switched on resulting in engine not starting due
to absence of fuel and ignition.
Fuel pump relay
The fuel pump relay is fed from the ignition relay and
controlled by the engine management ECM. The relay
is activated in ignition key position 2 to prime the fuel
system for a period of time controlled by the ECM.
Failure of this relay will result in no fuel pressure.
Inertia switch
The inertia switch isolates the power supply to the fuel
pump in the event of sudden deceleration. The inertia
switch is located in the engine compartment. It is reset
by depressing the central plunger at the top of the
switch.

SFI
27
REPAIR ADD: 09/95
11.Disconnect vent line quickfit connector from
liquid/vapour separator.
12.Remove torque screw cap from hose to tank
filler neck clip.
13.Loosen clip screw securing hose to tank filler
neck.
14.Release hose from filler neck and internal filler
neck breather hose from fuel tank.
15.Remove and discard fuel filler neck clip.
16.Disconnect the pressure sensor breather pipe
connection.
17.Disconnect the vent line hose connection.
18.Fit ignition key to fuel filler flap lock and open
flap.
19.Release fuel filler cap from filler neck.
20.Remove filler neck assembly from vehicle.
Do not carry out further dismantling if
component is removed for access only.
21.Remove torque screw cap from hose to filler
neck clip.
22.Loosen clip screw securing hose to filler neck.
23.Remove hose from filler neck.
24.Remove and discard fuel filler hose clip.
25.Remove vent line from filler neck.

19FUEL SYSTEM
28
REPAIRADD: 09/95 Refit
26.Fit vent line to filler neck.
27.Fit NEW clip to filler neck hose.
28.Fit hose to filler neck.
29.Position filler neck hose clip and tighten until
head shears.
30.Fit filler neck assembly to vehicle.
NOTE: To aid fitment of filler neck through
body grommet apply a soap solution to lip
of grommet.
31.Fit NEW clip to fuel filler neck hose.
32.Connect fuel filler neck internal breather to tank.
33.Connect fuel filler neck hose to tank.
34.Position fuel filler neck hose clip and tighten until
head shears.
35.Connect vent line quickfit connector to
liquid/vapour separator.
36.Connect the pressure sensor breather pipe
connection.
37.Connect the vent line hose connection.
38.Fit mud flap and secure with nuts and bolts.
39.Position filler neck support bracket and earth
strap to mud flap bracket and secure with nut
and bolt.
40.Remove stand(s) and lower vehicle.
41.Reposition loadspace sound insulation and
carpet.
42.Fit RH luggage compartment side panel.
See
CHASSIS AND BODY, Repair,
43.Fit tail door tread strip and secure with screws.
44.Refill tank with drained fuel.
45.Fit fuel filler cap to filler neck.
46.Close filler flap, lock with ignition key and
remove key.
47.Reconnect battery negative lead.FUEL TANK FILLER CAP - ADVANCED EVAPS
Service repair no - 19.55.08
Remove
1.Fit ignition key to fuel filler flap lock and open
flap.
2.Remove screw securing cap retaining strap to
body.
3.Remove fuel filler cap.
Refit
4.Fit fuel filler cap.
5.Position cap retaining strap to body and secure
with screw.
6.Close filler flap, lock with ignition key and
remove key.

41TRANSFER GEARBOX
4
REPAIR SHIFTLOCK SOLENOID/NEUTRAL SWITCH
Service repair no - 41.10.63/64
This is sited on top of the transfer gearbox. Access to
the component is gained through the transmission
tunnel aperture.
Remove
1.Disconnect battery negative lead.
2.Remove centre console.
See CHASSIS AND
BODY, Repair, Centre Console
3.Remove rear passenger heater air ducts.
4.Remove insulation pad.
5.Remove four screws and remove main gear
lever assembly.
6.Drill out rivets and remove tunnel blanking plate.
7.Disconnect solenoid multiplug.
8.Remove four retaining bolts and remove shiftlock
solenoid cover.
9.Remove solenoid and spring washer.
10.Clean joint sealant from mating faces.
KEY
1. Gearlever
2. Transmission tunnel aperture
3. Transfer gearbox
4. Bolt
5. Switch
6. Solenoid
7. Electrical connectionsRefit
1.Apply Hylosil or equivalent sealant to mating
faces.
2.Ensure solenoid plug lead is located in cover
recess.
3.Reverse removal procedure.
4.Fit four solenoid bolts. Tighten to
9Nm.
Neutral switch, audible alarm
1.Disconnect neutral switch electrical plug.
2.Remove neutral switch from transfer box.
Refit
3.Apply Hylomar PL32/L20 or SL500 sealant to
neutral switch.
4.Reverse removal procedure.
5.Switch - Tighten to
25Nm.