lock LAND ROVER DISCOVERY 1995 Workshop Manual

ELECTRICAL
15
REPAIR Refit
9.If removed fit the mounting plate to the actuator.
10.Engage the actuator operating rod with hooked
end of the actuator link.
11.Fit the actuator and mounting plate to the door
and loosely secure with the four screws.
12.Set the mounting plate with the screws in the
centre of the slotted holes, then tighten the
screws.
13.Connect the actuator lead to the door harness.
14.Reconnect battery negative lead.
15.With the sill locking button held in position, set
the bellcrank to approximately the position it
would be in if the sill button was depressed to
half of its total movement.
16.At this setting check the electrical operation of
the door lock. Adjust the mounting plate as
necessary to achieve the correct setting. Fully
tighten the securing screws on completion.
17.Refit the vapour barrier.
18.Connect the sill button operating rod to the
bellcrank, hold in position, fit the door trim panel
and the door pull.
BULB REPLACEMENT
For bulb type and rating refer to rating shown on the
bulb or bulb replacement list.
See GENERAL
SPECIFICATION DATA, Information, Bulbs
HEADLIGHT
Service repair no - 86.40.02/13
Remove
1.Rotate three retaining clips 10 degrees, to align
with slots in headlight mounting plate.
2.Withdraw light unit
NOTE: Detach adjustment operating rod
on vehicles fitted with headlight levelling.3.Disconnect electrical multiplugs and remove
headlight unit.
4.Release spring clips and withdraw headlight
bulb.
Key
1. Headlight
2. Retaining clips
3. Bulb
4. Spring clip
5. Cover
6. Bulb sidelight
7. Plug
8. Plug sidelight
Refit
5.Reverse removal procedure.

86ELECTRICAL
16
REPAIR SIDELIGHT BULB
Service repair no - 86.40.33
Remove
1.Remove headlight,
See Headlight
2.Disengage bulb holder by twisting a quarter turn
anti-clockwise.
3.Withdraw bulb from holder.
Refit
4.Reverse removal procedure.FRONT DIRECTION INDICATORS
Service repair no - 86.40.41
Remove
1.Pull spring clips, release from location and lift out
direction indicator unit.
2.Turn bulb holder anti-clockwise to release from
indicator unit.
3.Push and twist the bulb to remove.
Refit
4.Reverse removal procedure. When replacing
light unit, locate the two lugs at the bottom of the
lens before re-engaging spring clips.

ELECTRICAL
17
REPAIR REAR LIGHT UNIT
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Disconnect wiring harness multi-plug from light
unit.
4.Remove retaining nuts and withdraw light unit
from rear of vehicle.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure. Ensure that the
rubber seal is seated correctly.STOP, REVERSING, FOG GUARD BULBS
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Turn bulb holder anti-clockwise to release.
4.Remove bulb.
NOTE: On vehicles fitted with rear air
conditioning remove access panel
housing rear loadspace light to gain
access.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure.

86ELECTRICAL
18
REPAIR REAR LIGHTS, BUMPER MOUNTED
Service repair no - 86.41.42
Remove
1.From behind bumper disconnect light plugs.
2.Unscrew two retaining nuts and remove light unit
from bumper.
Refit
3.Reverse removal procedure.
NOTE: The black lead plug fits into the
direction indication light, the white lead
plugs into the tail light, the bulb holder
being colour coded red.DIRECTION INDICATOR, TAIL LIGHT BULBS
Service repair no - 86.41.43
Remove
1.Turn bulb holder anti-clockwise to release from
light unit.
2.Push and twist the bulb to remove.
Refit
3.Reverse removal procedure.

86ELECTRICAL
20
REPAIR HIGH MOUNTED STOP LIGHT
Service repair no - 86.41.35
Remove
1.Remove two screws and lift off light reflector
body.
2.Unscrew retaining nut and remove lens unit from
rear door glass.
Refit
3.Reverse removal procedure.STOP LIGHT BULB
Service repair no - 86.40.87
Remove
1.Remove reflector body.
2.Turn bulb holder anti-clockwise to release from
light unit.
3.Push and twist the bulb to remove.
Refit
4.Reverse removal procedure.

86ELECTRICAL
22
REPAIR SIDE REPEATER LIGHT
Service repair no - 86.50.59
Remove
1.Push the lens to the right and then pull outward
to detach lens and bulb holder from the panel.
2.Turn lens anti-clockwise and remove from bulb
holder.
3.Pull bulb from holder.
Refit
4.Reverse removal procedure.BUMPER MOUNTED SIDE LIGHT
Service repair no - 86.50.59
Remove
1.From behind bumper turn holder anti-clockwise
and release from light unit.
2.Pull bulb from holder.
Refit
3.Reverse removal procedure.

86ELECTRICAL
30
REPAIR INSTRUMENT ILLUMINATION AND WARNING
LIGHT BULBS
Service repair no - 86.45.48 - Instrument
Service repair no - 86.45.61 - Warning light
Remove
1.Remove binnacle.
See Instrument binnacle
2.Identify bulb to be replaced.
NOTE: If faulty bulb is not accessible,
remove screws securing circuit board and
carefully ease circuit board aside.
3.Rotate bulb holder anti-clockwise, withdraw bulb
holder and remove bulb.Refit
4.Fit new bulb to holder.
CAUTION: Ensure bulb of correct wattage
and type is fitted.
5.Reverse removal procedure.

86ELECTRICAL
38
REPAIR REVERSE LIGHT SWITCH
Service repair no - 37.27.01
Manual Gearbox
Remove
Reverse light switch is located at rear of selector
housing, accessible from beneath vehicle.
1.Place vehicle on suitable ramp.
2.Disconnect the battery negative lead.
3.Disconnect electrical leads.
4.Release lock-nut.
5.Remove switch.
NOTE: Reverse light switch requires
re-setting on reassembly.
6.Select reverse gear.
7.Connect 12 volt supply and test lamp across
switch terminals.
8.Screw switch into housing until test lamp is
illuminated. Screw switch in a further half turn,
tighten locknut.
9.Connect electrical leads.
10.Reconnect the battery negative lead.HEATER/VENTILATION AND AIR CONDITIONING
CONTROL PANEL BULB
Service repair no - 86.45.73
Remove
1.Carefully pull 3 rotary knobs off switches.
2.Prise blower speed control knob off lever.
3.Remove 2 screws securing panel, ease panel
away from fascia.
4.Pull bulb from holder.
5.Insert new bulb in holder.
Refit
6.Reverse removal procedure.

ELECTRICAL
49
REPAIR Refit
8.Fit bulb to lens.
9.Secure bulb retaining clip.
10.Connect 2 Lucars to bulb.
11.Position lamp lens to shroud.
12.Position lamp to bracket and secure fog lamp
adjustment ball joint to bracket.
13.Position spacers, align lamp to bracket and
secure with Torx screws.
14.Fit front fog lamp.
See fog lamp - front; Refit
CLOCK
Service repair no - 88.15.07
Remove
1.Remove drinks tray.
See CHASSIS AND
BODY, Repair, drinks tray
2.Release 4 clock panel securing tags.
3.Release clock panel from louvre panel.
4.Disconnect 2 multiplugs from clock.
5.Remove clock.
Refit
6.Position clock.
7.Connect multiplugs to clock and secure clock to
louvre panel.
8.Fit drinks tray.
See CHASSIS AND BODY,
Repair, drinks tray; Refit
REAR SPEAKER
Service repair no - 88.15.12
Remove
1.Remove 4 screws securing speaker.
2.Release speaker and disconnect 2 Lucars.
3.Remove speaker.
Refit
4.Position speaker, connect Lucars and secure
with screws.