engine oil LAND ROVER DISCOVERY 1995 Owner's Manual

10MAINTENANCE
12
MAINTENANCE
EXTERNALLY CHECK INTERCOOLER FOR
OBSTRUCTION - Tdi
Clear any trapped dirt or flies from vanes of
intercooler
CLEAN INTERCOOLER ELEMENT - Tdi
Remove
1.Remove intercooler element.
2.Flush intercooler with ICI 'GENKLENE'or
à oD-SOLVE' propriety cleaner, following the
manufacturer's instructions.
3.Dry the intercooler completely ensuring that no
liquid remains in the element.
Refit
4.Refit intercooler element.UNDER VEHICLE MAINTENANCE
Vehicles operating under severe conditions of dust,
sand, mud and water should have oils changed and
lubrication carried out at more frequent intervals than
is recommended in maintenance schedules.
RENEW ENGINE OIL AND FILTER - Tdi
CAUTION: Serious damage to the
turbocharger will result if engine is run
above idling speed before oil pressure is
restored.
RENEW ENGINE OIL - V8i
RENEW ENGINE OIL AND FILTER - V8i
CAUTION: To prevent an airlock occuring
after removing filter, fill new filter with oil
and fit immediately after removing old
filter. If airlock does occur fill oil pump with
petroleum jelly.
RENEW ENGINE OIL AND FILTER - Mpi
CHECK/TOP UP MANUAL GEARBOX OIL - V8i
1.Site vehicle on lift or level ground.
2.Remove oil filler level plug. If necessary, inject
new oil into the gearbox until it runs out of filler
hole. Fit plug. Tighten to
30 Nm.
RENEW MANUAL GEARBOX OIL - Tdi - Mpi
RENEW MANUAL GEARBOX OIL - V8i

MAINTENANCE
13
MAINTENANCE
RENEW AUTOMATIC GEARBOX FLUID AND OIL
SCREEN
1.Site vehicle on lift or level ground. Place
container to drain gearbox fluid into. Disconnect
battery negative lead.
2.Remove gearbox dipstick, located at rear of right
hand rocker cover, to aid oil drainage. Release
plug from bottom of sump and allow fluid to drain
completely.
3.Refit plug using a new sealing washer. Tighten
to
10 Nm
Refill ZF Automatic Gearbox and Check Fluid
Level.
NOTE: The fluid level must checked when
fluid is cold and engine idling in park.
4.Ensure vehicle is on level ground.
5.Refill or top-up with correct quantity and grade of
fluid.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
6.Start and run engine. Apply footbrake, select
position 1 then back to park. Check fluid level,
this must be between the two marks on the
dipstick.
Oil screen replacement ZF automatic gearbox.
See AUTOMATIC GEARBOX, Repair, Oil Screen

12ENGINE
4
REPAIR 22.Disconnect feed pipe and spill return pipe from
injector pump.
23.Disconnect both pipes from fuel lift pump.
24.Disconnect servo hose from vacuum pump.
25.Remove three retaining nuts and disconnect
exhaust down pipe.
26.Remove oil cooler pipes from oil filter adaptor.
27.If automatic transmission is fitted, disconnect
feed and return pipes at gearbox oil cooler.
Remove retaining bracket from LH side of
cylinder block and release both oil cooler pipes.
28.Support gearbox.
29.Disconnect ground strap from starter motor.
30.On vehicles with automatic transmission, remove
fixings and detach drive plate housing access
panel and gasket.31.Working through drive plate housing aperture
mark the torque convertor and drive plate to
facilitate reassembly.
32.Remove the four convertor to flexible drive
securing bolts, rotating crankshaft to gain access
to each individual bolt.
33.Fit engine lifting bracket to the two RH rear
cylinder head fixing bolts.
34.Using suitable hoist, fit lifting chains to engine.
35.Remove four bolts, from both sides, securing
front engine mounting brackets to cylinder block.
36.Remove two bolts, from both sides, securing
front engine mounting bracket to bell housing.

Tdi
9
REPAIR Belt tensioner
NOTE: The belt tensioner need only be
removed if it is being replaced or for
access purposes to remove front cover.
11.Remove securing bolt and withdraw tensioner
complete with spacer.
Crankshaft gear/front cover oil seal
12.If the crankshaft gear cannot be removed by
hand, use special tool LRT-12-078 with main
body and thrust button from special tool
LRT-12-031 as illustrated ST3478M. Withdraw
gear complete with 'O' ring seal.
13.If necessary prise out oil seal from front cover.
14.Lubricate a new crankshaft oil seal with clean
engine oil.
15.With lip side leading, drive-in seal squarely using
special tool LRT-12-079.
16.Lubricate new 'O' ring seal with petroleum jelly
and slide onto shaft, taking care not to damage
seal on the woodruff keys.
17.Fit crankshaft gear, tap fully home ensuring 'O'
ring seal is properly seated.
CAMSHAFT GEAR/FRONT COVER OIL SEAL
Service repair no - 12.13.05
18.Remove centre bolt from camshaft gear and
withdraw gear.
19.Remove existing oil seal from front cover using
special tool LRT-12-038.
20.Lubricate a new camshaft oil seal with clean
engine oil.

12ENGINE
12
REPAIR FRONT COVER/TIMING GEAR HOUSING GASKET
Service repair no - 12.65.10
Remove
1.Remove timing belt and gears.
See Camshaft
Drive Belt and Gears
2.Remove fuel injection pump.See FUEL
SYSTEM, Repair, Fuel Injection Pump and
Timing
3.Remove engine oil sump.See Oil Sump
4.Remove oil pick up strainer.See Oil Pick-Up
Strainer
5.Remove bolts securing timing gear housing to
block.
6.Withdraw timing gear housing complete with
gasket.
7.Clean all gasket material from mating faces.
Refit
8.Fit slave guide studs to locate gasket.
9.Fit new gasket, over slave studs, to cylinder
block.
10.Align flats on oil pump with flats on crankshaft.
11.Fit front cover to block taking care not to damage
oil seal.
12.Secure with bolts of correct length in locations
where slave studs are not fitted (ST3482).
13.Remove slave studs and fit correct length bolts.
14.Tighten to
25 Nm.
15.Fit oil pick-up strainer.See Oil Pick-Up
Strainer
16.Fit oil sump.See Oil Sump
17.Refit fuel injection pump.See FUEL SYSTEM,
Repair, Fuel Injection Pump and Timing

Tdi
13
REPAIR OIL SUMP
Service repair no - 12.60.44
Remove
1.Disconnect battery negative lead.
2.Drain engine oil.
3.Slacken sump securing bolts and, using a sharp
knife, break sealant around sump flange.
4.Remove bolts and withdraw sump.
Refit
5.Clean mating faces of sump, timing gear housing
and cylinder block.
6.Apply a 2,0 mm bead of 'Hylosil RTV102' to the
sump flange, ensuring bead is applied inboard of
the bolt holes.
7.Secure sump to block with bolts. Tighten to
25
Nm.
8.Refill engine oil.See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids
9.Reconnect battery negative lead.OIL PICK-UP STRAINER
Service repair no - 12.60.20
Remove
1.Disconnect battery negative lead.
2.Drain engine oil.
3.Remove engine oil sump.
See Oil Sump
4.Remove bolts securing pipe support bracket.
5.Remove bolts from pipe flanges.
6.Withdraw pick-up strainer assembly.
Refit
7.Refit pick-up strainer assembly, fitting a new 'O'
ring seal at oil pump connection.
8.Apply Loctite 242E to the two screws at the
bearing cap. Tighten to
9 Nm.
9.Fit bolts to pipe flanges. Tighten to25 Nm.
10.Refit engine oil sump.See Oil Sump
11.Reconnect battery negative lead.

Tdi
15
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
NOTE: The crankshaft rear oil seal is
retained in its own housing, if the seal
requires replacing the housing and seal
assembly (1) must be renewed complete with the
housing seal (3). Housing and seal assemblies are
supplied with their own former/seal guide (2)
already fitted. This former must not be removed
before fitting the assembly to the engine. If a seal
and housing assembly is received without a
former/guide fitted it must be returned to the
supplier. Used formers/guides must be discarded
immediately after use, under no circumstances
should they be reused on other assemblies.
1.Disconnect battery negative lead.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
Assembly
4.Remove flywheel.See Flywheel
5.Remove five bolts and withdraw seal housing
and seal assembly complete with gasket.
Refit
6.Insert slave studs to seal housing mounting face.
7.Position new seal housing gasket over slave
studs and crankshaft flange onto cylinder block.

12ENGINE
18
REPAIR 10.Apply sealant to flywheel housing mating face on
cylinder block (Fig. J5944).
11.Fit housing to cylinder block and secure with
bolts as removed. Tighten to
45 Nm.
12.Remove surplus sealant from block.
13.Refit starter motor.
14.Refit flywheel.
See Flywheel
15.Refit clutch.See CLUTCH, Repair, Clutch
Assembly
16.Refit gearbox.See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
17.Reconnect battery negative lead.OIL FILTER
Service repair no - 12.60.01
Remove
1.Place drain tray under filter.
2.Unscrew filter anti-clockwise, using a strap or
spanner.
Refit
3.Smear clean engine oil on seal of new filter.
4.Screw on filter until sealing ring touches
machined face, then tighten a further half turn by
hand only. Do not over tighten.

12ENGINE
22
REPAIR
NOTE: Cylinder head retaining bolts can
be used up to a maximum of five times.
34.Lubricate threads of bolts with light oil and fit to
positions illustrated.
Bolt sizes:
M10 x 117mm locations 3, 5, 12, and 13.
M12 x 140mm locations 1, 2, 7, 8, 9, 10, 15, 16, 17,
and 18.
M12 x 100mm locations 4, 6, 11, 14.
35.Tighten bolts so that underside of heads just
make contact with cylinder head.
36.Following the sequence illustrated tighten all
bolts to
40 Nm.
37.Attach degree disc special tool LRT-12-007 to a
power bar.
38.Make a suitable pointer from welding rod and
attach to a bolt screwed into a rocker shaft
securing bolt hole.
39.Tighten all bolts through 60°strictly in sequence
illustrated.
40.Repeat 60°tightening procedure, again strictly in
sequence illustrated.
41.Tighten the ten longer bolts (M12 x 140mm) a
further 20°, again following the sequence
illustrated.
NOTE: Repositioning of the pointer will be
necessary to reach all bolts, the pointer
can be fitted to the rocker shaft securing
studs using two nuts.
CAUTION: The double tightening
procedure must be carried out, on no
account should tightening be performed in
one operation, otherwise damage to the cylinder
head may occur.
42.Fit valve stem caps.
43.Fit push rods to locations from which they were
removed.
44.Fit rocker shaft assembly evenly tightening
securing nuts and bolts to correct torque.
45.Fit rocker cover ensuring oil seal is satisfactory
for continued use.
NOTE: Rocker cover seals can be re-used
up to a maximum of five times.
46.Secure rocker cover with special seal washers
and nuts tightened to correct torque.
47.Refit remainder of items by reversing operations
1 to 22 tightening securing bolts to correct torque
where applicable.

Tdi
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine block
Bearing cap 133...............................................................................................
Blanking plug, oil gallery, rear 37....................................................................
Oil squirt jet assembly 17................................................................................
Drain plug, cylinder block 25...........................................................................
Oil squirt jet, vacuum pump cam 7.................................................................
Connecting rod to cap 59................................................................................
Oil pick up assembly to bearing cap 9...........................................................
Oil pick up assembly to front cover 25............................................................
Camshaft thrust plate 9..................................................................................
Oil drain pipe to block (internal) 25.................................................................
Oil drain pipe to block (external) 25................................................................
Sump to cylinder block and front cover 25......................................................
Drain plug, oil sump 35...................................................................................
Tappet guide 14..............................................................................................
Breather side cover assembly 25....................................................................
Baffle plate to breather side cover 4..............................................................
Vacuum pump 25............................................................................................
Fuel lift pump 25.............................................................................................
Flywheel housing 45.......................................................................................
Flywheel housing clutch cover stud 10...........................................................
Plug, flywheel housing 12...............................................................................
Rear oil seal assembly 25...............................................................................
Oil filter adaptor 45..........................................................................................
Waxstat adaptor to oil filter adaptor 9............................................................
Oil pressure switch 17.....................................................................................
Oil filter, spin on 13.........................................................................................
Oil cooler unions to filter adaptor 45...............................................................
Oil level tube 25..............................................................................................
Engine mounting foot to cylinder block 85......................................................
Engine mounting foot to flywheel housing 45.................................................
Engine mounting foot rubber to mounting foot (bolt and nut) 85.....................
Flywheel to crankshaft 146..............................................................................
Clutch cover plate to flywheel 34....................................................................
Flex drive plate to crankshaft (auto) 146..........................................................
Flex drive plate to ring gear (auto) 25.............................................................
Flex drive plate to torque converter (auto) 45.................................................