remote control LAND ROVER DISCOVERY 1995 Workshop Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 1995, Model line: DISCOVERY, Model: LAND ROVER DISCOVERY 1995Pages: 873, PDF Size: 12.89 MB
Page 671 of 873

76CHASSIS AND BODY
4
REPAIR FRONT DOOR LOCK, OUTSIDE AND INSIDE
DOOR RELEASE HANDLES
Service repair no - 76.37.12/31
Remove
1.Disconnect battery negative lead.
2.Remove the door trim panel.
See front door
trim panel.
3.Remove the door glass and regulator.See
front door glass and regulator.
4.Where applicable remove the door actuator unit.
See ELECTRICAL, Repair, front door
actuator unit.
5.Disconnect the lock barrel control rod from the
lock by releasing the metal clip at the bottom of
the rod.6.Disconnect the control rod from the outside door
release handle by pulling it out of the plastic
ferrule.
7.Disconnect the remote button control rod from
the lock by releasing the metal clip at the bottom
of the rod and withdraw the rod from the door.
8.Disconnect the control rod connector between
the inside door release handle and the door lock
by releasing the metal clip and pulling one of the
control rods out of the plastic connecting block.
This is accessible through the small centre
cut-out in the door panel. The control rod also
passes through a guide bracket in the inside of
the inner door panel.
9.From inside the door panel push out the small
pin that secures the quadrant to the inner door
panel. Push the quadrant out of the panel.
10.Release the door lock by removing the two
counter-sunk screws from the door edge and the
single screw and shakeproof washer on the
inner door panel.
Page 679 of 873

76CHASSIS AND BODY
12
REPAIR REAR DOOR TRIM PANEL
Service repair no - 76.34.09
Remove
1.Remove the two screws securing the door pull
and remove it from the door.
2.Remove the finisher from the inner door handle.
3.Using a trim panel removing tool release the
seventeen trim panel fasteners and withdraw the
panel from the door.
4.If necessary remove the sixteen screws securing
the stowage bins to the trim panel and detach
the bins.
Refit
5.Reverse removal procedure.REAR DOOR LOCK AND INNER AND OUTER
RELEASE HANDLES
Service repair no - 76.37.16/74/77/78
Remove
1.Disconnect battery negative lead.
2.Remove the door pull, the trim panel and the
vapour protective sheet, to allow access to the
door handles and lock mechanisms.
3.Disconnect the inner release handle connecting
rod at the lock.
4.Remove the two screws securing the inner
handle and withdraw the handle complete with
connecting rod.
NOTE: Two identical 'Y' shaped levers
(bellcranks) are fitted to the rear door lock
mechanism and are referred to as inner
and outer 'Y' levers; the inner one being the
nearest to the inner door panel.
5.If fitted, remove the central locking actuator
control rod link from the actuator and from the
inner 'Y' lever.
6.Detach the remote button connecting rod at the
inner 'Y' lever and withdraw from inside the door.
7.Detach the lock and barrel connecting rods from
the upper leg of the inner 'Y' lever.
Page 808 of 873

ELECTRICAL
5
DESCRIPTION AND OPERATION ANTI THEFT ALARM SYSTEM
The main function of the system is to offer easy to use
remote locking and unlocking of the vehicle without
having to actively select the alarm function.
ALARM COMPONENTS
COMPONENT LOCATION
1. Electronic control unit (ECU) and relays Passenger footwell.................
2. Bonnet switch RH engine bay..........................................................
3. Door switches
4. Alarm sounder RH engine bay.........................................................
5. Light emitting diode (LED) Dash panel.......................................
6. Ultrasonic unit Roof map pocket.........................................................
7. Lock barrel, sill buttons
8. Handset transmitter
9. Aerial 'A' post, passenger side........................................................................