rims LAND ROVER DISCOVERY 1995 Workshop Manual

57STEERING
10
FAULT DIAGNOSIS VISUAL AND SAFETY CHECKS
WARNING: Before taking vehicle out on
the public highway for road test, it is
important that the following basic visual
checks are carried out to ensure that the vehicle
complies with legal requirements.
Tyres and wheel rims
1.Check and adjust tyre pressures.
See
GENERAL SPECIFICATION DATA,
Information, Tyre Pressures
Note that this information refers to standard tyres
fitted as original equipment.
2.Check condition of tyres. Inspect for signs of
uneven wear, damage and feathering. Check
tread depth.
3.Ensure that the tyre make, type and general
condition are common across each axle.
4.Check wheel rims for signs of damage and
excessive run out.
5.Carry out road test.
See Road Test Procedure
ROAD TEST PROCEDURE
General steering/handling problems can usually be
classified into one of the categories listed and ARE
GENERALLY RELATED TO THE AGE, CONDITION
AND USE OF THE VEHICLE.
WARNING: Ensure that all road tests are
conducted by suitably qualified drivers in
a safe and legal manner, and where local
traffic conditions allow.
1.Carry out visual and safety checks.
See Visual
and Safety Checks
Confirm general nature of complaint with customer,
simulating where possible the conditions under which
the problem occurs. Carry out following road test
procedure to establish the problem.2.Steering load assessment - drive at 16 km/h (10
mph). Put 90°turn input into steering wheel,
check self centering. The self centering should
be equal on each lock BUT not necessarily
return to exactly straight ahead without
assistance from the driver.
3.Steering assessment - drive at 64 km/h (40 mph)
on a staight FLAT road (no camber), check for
steering veer. The vehicle should follow a
straight path with NO tendency to follow a
curved path. If vehicle veers towards the kerb,
vehicle may be 'camber sensitive'. A small
amount of veer in direction of camber is
acceptable.
4.Directional stability assessment - drive at 112
km/h (70 mph) or maximum legal speed on a
straight flat road. Carry out a normal lane
change. Vehicle should quickly settle into a new
straight path.
5.Braking assessment (medium effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply
steady medium braking effort, noting any
tendency to veer. Carry out brake test three
times, if a veer is consistently noted carry out a
braking efficiency test on a rolling road.
6.Braking assessment (full effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply full
braking effort, noting any tendency to veer. Carry
out brake test three times, if a veer is
consistently noted carry out a braking efficiency
test on a rolling road.
If the symptom described by the customer is stiff
steering or steering niggle, carry out stiff steering
procedure.
See Stiff Steering Checklist
If not proceed with basic checks and adjustments.
See Visual Check and Basic Adjustments

WHEELS AND TYRES
1
DESCRIPTION AND OPERATION TYPES OF WHEEL RIMS AND TYRES
Description
Dependent on specification, the vehicle is equipped
with alloy or pressed steel wheel rims, both using
tubeless radial ply tyres.
Tyre codes
The writing, codes and numbers moulded into the tyre
wall vary between tyre manufacturers, however most
tyres are marked with the information shown in the
illustrated example.
NOTE: The illustration is an example of the
type of markings moulded into tyres and is
for guidance only. For specific tyre
specifications.
See GENERAL SPECIFICATION
DATA, Information, Wheels and Tyres
1.Type of tyre construction -Radial Ply
2.Load index -104
3.Speed symbol -SorT
4.USA Tyre quality grading -Tread wear 160
Traction A temperature B
5.Tread wear indicators moulded into tread pattern
are located at intervals around the tyre and
marked by a code -E66 103S6
6.Tyres with 'Mud Snow' type tread pattern are
marked -M&S
7.Tyre reinforcing mark -Reinforced
8.USA Load and pressure specification -
900Kg(1984LBS) at 340KA (50PSI) MACS
PRESS
9.Tyre size -205 16 ot 235/70 R16
10.Type of tyre -TUBELESS
11.Country of manufacture -MADE IN GREAT
BRITAIN
12.USA Compliance symbol and identification -
DOT AB7C DOFF 267
13.European type approval identification -E11
01234
14.Tyre construction -SIDE WALL 2 PLIES
RAYON. TREAD 2 RAYON 2 STEEL
15.Manufacturer's brand name/type -TRACTION
PLUS mzx M

WHEELS AND TYRES
3
REPAIR WHEEL BALANCING
CAUTION: It is essential that all wheel
balancing is carried out off the vehicle.
The use of on the vehicle balancing could
cause component damage or personal injury and
MUST NOT be attempted.
NOTE: Before attempting to balance a
wheel and tyre assembly clean all mud and
dirt deposits from both inside and outside
rims and remove existing balance weights.
Remove stones from the tyre tread in order to avoid
operator injury during dynamic balancing and to obtain
the correct balance.
Inspect tyres for damage and correct tyre pressures
and balance according to the equipment
manufacturer's instructions.
Alloy wheels
Clean area of wheel rim and attach adhesive balance
weights in position shown. Cut through rear face of
weight strip to detach required weights.
CAUTION: Use only correct adhesive
balance weights to avoid damage to
aluminium wheel rim. DO NOT attempt to
use a steel wheel weight on an aluminium wheel.
Steel wheels
Clean area of wheel rim and attach balance weights in
position shown.