traction control LAND ROVER DISCOVERY 1995 Workshop Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 1995, Model line: DISCOVERY, Model: LAND ROVER DISCOVERY 1995Pages: 873, PDF Size: 12.89 MB
Page 80 of 873
10MAINTENANCE
18
MAINTENANCE
ABS VEHICLES - CHECK ROAD WHEEL SPEED
SENSOR ELECTRICAL HARNESS FOR DAMAGE
RENEW OXYGEN SENSORS
See EMISSION CONTROL, Repair, Heated
Oxygen Sensor (HO2S)
RENEW CATALYTIC CONVERTERS
See MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust System Complete
REPORT ANY UNUSUAL FEATURES OF VEHICLE
CONDITION AND ADDITIONAL WORK REQUIREDCARRY OUT ROAD TEST
For details of dynamometer testing.See
INTRODUCTION, Information, Dynamometer
Testing - Non Anti-lock brake vehicles See
INTRODUCTION, Information, Dynamometer
Testing - Vehicles with Anti-lock brakes (ABS)
Check following items:
1.Inhibitor switch only operates in P and N.
2.Engine for excessive noise.
3.Clutch for slip, judder or spin.
4.Automatic gear selection/shift speeds.
5.Gear selection/noise - high/low range.
6.Steering for abnormal noise/effort.
7.Steering for free play.
8.All instruments, gauges and warning indicators.
9.Heater and air conditioning systems.
10.Heated rear screen.
11.Shock absorbers - ride irregularities.
12.Foot brake, on emergency stop, pulling to one
side, binding, pedal effort.
13.Parkbrake efficiency.
14.Seat reclining and latching.
15.Fully extend seat belt, check operation of
retraction and latching. Inertia belts lock when
snatched or vehicle on slope.
16.Road wheel balance.
17.Transmission for vibrations.
18.Body noises, squeaks and rattles.
19.Excessive exhaust smoke.
20.Engine idle speed.
21.Endorse service record.
22.Report any unusual features of vehicle condition
and additional work required.
ENDORSE SERVICE RECORD
Page 739 of 873
80HEATING AND VENTILATION
2
DESCRIPTION AND OPERATION Through-flow ventilation
Through-flow ventilation is achieved by means of
one-way air extraction vents incorporated in both rear
quarter body panels. The vents open and close
automatically dependent upon the heating and
ventilation unit control settings and the volume of air
entering the vehicle.Heating and ventilation unit, controls
The Heating and Ventilation Unit is centrally located
and concealed by the dash assembly. When air
conditioning is fitted, an evaporator is mounted in the
heater unit forward of the heater matrix.
The dash mounted central controls are used to
operate both systems. A single switch controls the air
conditioning unit when fitted.
Controls set for maximum heat to footwells and face level vents
Heating and ventilation flaps and air flow key
1. Fresh or recirculated air from blower unit
2. Evaporator matrix - air conditioning (when fitted)
3. Heater matrix
4. Air outlet front footwells
5. Air outlet to rear footwells
6. Air outlet face level vents7. Air outlets screen de-mist
8. Control flap - face level vents
9. Control flap - demist vents
10. Control flap - air direction
11. Control flap - air temperature
12. Control flap - air direction
Page 854 of 873
86ELECTRICAL
34
REPAIR PRINTED CIRCUIT AND WARNING LIGHTS
1. Panel illumination bulbs
2. Transmission oil temperature warning lamp bulb
3. Hazard warning lamp bulb
4. Check engine warning lamp bulb
5. Handbrake/brake fluid warning lamp bulb
6. ABS warning lamp bulb
7. Headlamp main beam warning lamp bulb
8. Trailer direction warning lamp bulb9. Direction indicator warning lamp bulb
10. Air suspension warning lamp bulb
11. Ignition/no charge warning lamp bulb
12. Seat belt warning lamp bulb
13. Not used
14. Traction control warning lamp bulb
15. Diesel heater plug warning lamp bulb (if fitted)
16. Main printed circuit