battery replacement LAND ROVER FREELANDER 2001 User Guide

PANEL REPAIRS
77-2-32 REPAIRS
Front sidemember (front section)
In this procedure, the front section of the front
sidemember closing panel and the related
crossmember to sidemember gusset plate are
replaced in conjunction with the front sidemember.
Remove
1.Disconnect battery earth lead.
2.Disconnect all ECUs.
3.Remove road wheel(s).
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
6.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
7.Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
8.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
9.Release wiring to headlamp and position aside.
10.Remove engine bay shield.
11.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
12. LH side: Remove front bumper LH support
bracket.
13. LH side: Remove ECM.
14. LH side: Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
15. LH side: Remove air cleaner.
16. LH side: Remove air intake hose.
17. LH side: Remove horn.

+ SECURITY, REPAIRS, Horn.
18. RH side: Remove front bumper RH support
bracket.
19. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
20. RH side: Remove alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - KV6.
21. RH side: Remove PAS pump.

+ STEERING, REPAIRS, Pump -
steering - KV6.Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
77-2-34 REPAIRS
26. LH side: Remove LH engine mounting from
body.
27. LH side: On models with Diesel engines,
remove fuel filter.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Filter - main - up to 03MY.
28. LH side: Remove LH front brake pipe.
29. RH side: Remove front bumper RH support
bracket.
30. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
31. RH side: Remove coolant expansion tank.
32. RH side: Remove RH engine mounting from
body.
33. RH side: Remove PAS fluid reservoir.
34. RH side: Remove RH front brake pipe.
35. Driver's side: Remove passenger
compartment fuse box.
36.Remove brake pedal box and brake servo.
37.Remove clutch pedal box.
38.Release vehicle harness from valance and
position aside.
39.Remove treadplate from front door aperture.
Release front carpet and position aside.
40.Remove insulation pads from engine bulkhead.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1.Fit insulation pads to front and rear sides of
engine bulkhead.
2.Position front carpet and fit treadplate to front
door aperture.
3.Secure vehicle harness to valance.
4. Driver's side: Fit clutch pedal box.
5.Fit brake pedal box and brake servo.
6.Fit passenger compartment fuse box.
7. LH side: Fit LH front brake pipe. Bleed brake
system.
+ BRAKES, ADJUSTMENTS, Brake
bleed.
8. LH side: On models with Diesel engines, fit fuel
filter.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Filter - main - up to 03MY.
9. LH side: Fit LH engine mounting to body.
10. LH side: Fit engine compartment fuse box and
related wiring.
11. LH side: Fit battery carrier. Do not connect
battery earth lead.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
12. LH side: Fit engine compartment fusebox.
13. LH side: Fit ECM.
14. LH side: Fit air intake hose.
15. LH side: Fit air cleaner.
16. LH side: Fit front bumper LH support bracket.
17. RH side: Fit RH front brake pipe. Bleed brake
system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
18. RH side: Fit PAS fluid reservoir.
19. RH side: Fit RH engine mounting to body.
20. RH side: Fit coolant expansion tank.
21. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
22. RH side: Fit front bumper RH support bracket.
23.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
24.Fit PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
25.Fit front damper.

+ FRONT SUSPENSION, REPAIRS,
Damper.
26.Fit engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
27.Fit front suspension rear beam.
28.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.

PANEL REPAIRS
77-2-36 REPAIRS
Valance upper front
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
6.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
7.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
8.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
9.Release wiring from valance and position
aside.
10. LH side: Remove ECM.
11. LH side: Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
12. RH side: Remove PAS fluid reservoir.
13. RH side: Remove brake pipes from valance.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1. LH side: Fit battery. Do not connect earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
2. LH side: Fit ECM.
3. RH side: Fit PAS fluid reservoir.
4. RH side: Fit brake pipes to valance. Bleed
brakes.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
5.Secure wiring to valance.
6.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
7.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
8.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
9.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
10.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
11.Connect all ECUs.
12.Connect alternator.
13.Connect battery earth lead.

PANEL REPAIRS
REPAIRS 77-2-37
Valance front
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
6.Remove engine bay shield.
7.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
8.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
9.Remove front bumper support bracket.
10.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
11.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
12.Release wiring to headlamp and position aside.
13. LH side: Remove air cleaner.
14. LH side: Remove air intake hose.
15. LH side: Remove ECM.
16. LH side: Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
17. LH side: Remove engine compartment fuse
box and related wiring.
18. LH side: Remove LH front brake pipe.
19. RH side: Remove PAS fluid reservoir.
20. RH side: Remove RH front brake pipe.
21. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
22. RH side: Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
REPAIRS 77-2-39
Valance outer reinforcement
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
6.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
7.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
8.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
9.Release wiring from valance and position
aside.
10. LH side: Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
11. LH side: Remove ECM.
12. LH side: Remove relay module.
13. LH side: Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
14. LH side: Remove engine compartment fuse
box and related wiring.
15. RH side: Remove PAS fluid reservoir.
16. RH side: Remove brake pipes from valance. Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1. LH side: Fit engine compartment fuse box and
related wiring.
2. LH side: Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
3. LH side: Fit relay module.
4. LH side: Fit ECM.
5. LH side: Fit battery. Do not connect earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
6. RH side: Fit PAS fluid reservoir.
7. RH side: Fit brake pipes to valance. Bleed
brakes.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
8.Secure wiring to valance.
9.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
10.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
11.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
12.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
13.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
14.Connect all ECUs.
15.Connect alternator.
16.Connect battery earth lead.

PANEL REPAIRS
77-2-40 REPAIRS
'A' post - 3 door
In this procedure, the front outer body side panel is
replaced in conjunction with the inner 'A' post and the
'A' post reinforcements.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
6.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
7.Remove front door.

+ DOORS, REPAIRS, Door assembly
- front - remove for access & refit.
8.Remove front seat.

+ SEATS, REPAIRS, Front seat.
9.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
10.Remove duct of outboard face level ventilator.
11.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
12.Remove windscreen.

+ SCREENS, REPAIRS, Windscreen.
13.Remove treadplate from front door aperture.
Release front carpet and position aside.
14.Remove front door aperture seal.
15.Remove engine bulkhead insulation.
16. Driver's side: Remove passenger
compartment fuse box.
Repair1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
77-2-42 REPAIRS
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1. Driver's side: Fit passenger compartment fuse
box.
2.Fit insulation pads to engine bulkhead.
3.Fit front door aperture seal.
4.Position front carpet and fit treadplate to front
door aperture.
5.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
6.Fit windscreen.

+ SCREENS, REPAIRS, Windscreen.
7.Fit duct of outboard face level ventilator.
8.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
9.Fit front seat.

+ SEATS, REPAIRS, Front seat.
10.Fit front door.

+ DOORS, REPAIRS, Door assembly
- front - remove for access & refit.
11.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
12.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
13.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
14.Connect all ECUs.
15.Connect alternator.
16.Connect battery earth lead.

PANEL REPAIRS
REPAIRS 77-2-43
Sill reinforcement - 3 door
In this procedure, the lower outer body side panel is
replaced in conjunction with the sill reinforcement.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
6.Remove front door.

+ DOORS, REPAIRS, Door assembly
- front - remove for access & refit.
7.Remove front seat.

+ SEATS, REPAIRS, Front seat.
8.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
9.Remove treadplate from front door aperture.
10.Remove side door aperture seal.
11.Remove rear body side casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - body side - rear - 3
door.
12.Release carpet from inner sill and position
aside.
13.Release vehicle harness from inner sill and
position aside.
Repair1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1.Secure vehicle harness to inner sill.
2.Position carpet to inner sill.
3.Fit rear body side casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - body side - rear - 3
door.
4.Fit side door aperture seal(s).
5.Fit treadplate to side door aperture(s).
6.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
7.Fit front seat.

+ SEATS, REPAIRS, Front seat.
8.Fit front door.

+ DOORS, REPAIRS, Door assembly
- front - remove for access & refit.
9.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
10.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
11.Connect all ECUs.
12.Connect alternator.
13.Connect battery earth lead.

PANEL REPAIRS
77-2-44 REPAIRS
Sill reinforcement - 5 door
In this procedure, the lower outer body side panel is
replaced in conjunction with the sill reinforcement.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
6.Remove front door.

+ DOORS, REPAIRS, Door assembly
- front - remove for access & refit.
7.Remove rear door.

+ DOORS, REPAIRS, Door assembly
- rear - remove for access & refit.
8.Remove 'B/C' post lower finisher.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'B' post - lower - 5
door.
9.Remove front seat.

+ SEATS, REPAIRS, Front seat.
10.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
11.Remove treadplate from side door apertures.
12.Remove side door aperture seals.
13.Release carpet from inner sill and position
aside.
14.Release vehicle harness from inner sill and
position aside.
Repair1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1.Secure vehicle harness to inner sill.
2.Position carpet to inner sill.
3.Fit side door aperture seals.
4.Fit treadplate to side door apertures.
5.Fit rear seat.
+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
6.Fit front seat.

+ SEATS, REPAIRS, Front seat.
7.Fit 'B/C' post lower finisher.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'B' post - lower - 5
door.
8.Fit rear door.

+ DOORS, REPAIRS, Door assembly
- rear - remove for access & refit.
9.Fit front door.

+ DOORS, REPAIRS, Door assembly
- front - remove for access & refit.
10.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
11.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
12.Connect all ECUs.
13.Connect alternator.
14.Connect battery earth lead.

PANEL REPAIRS
REPAIRS 77-2-45
'B/C' post reinforcement - 3 door
In this procedure, the rear outer body side panel and
the rear quarter front lower reinforcement are
replaced in conjunction with the 'B/C' post
reinforcement.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove rear wheel arch extension.

+ EXTERIOR FITTINGS, REPAIRS,
Wheelarch extension - rear wing part.
6.Remove rear wheel arch liner.
7.Remove front seat belt.

+ RESTRAINT SYSTEMS, REPAIRS,
Automatic belt assembly - front - 3 door.
8.Remove front door striker from 'B/C' post.
9.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
10.Remove rear body side casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - body side - rear - 3
door.
11.Remove treadplate from side door aperture.
12.Remove side door aperture seal.
13.Release carpet from inner sill and position
aside.
14.Remove rear quarter vent and seal.

+ EXTERIOR FITTINGS, REPAIRS,
Body quarter vent assembly - 3 door.
15.Remove rear roof panel finisher.
16.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
17.Release vehicle harness from inner sill and
position aside. Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.