airbag LAND ROVER FREELANDER 2001 Owner's Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 2001, Model line: FREELANDER, Model: LAND ROVER FREELANDER 2001Pages: 1007, PDF Size: 23.47 MB
Page 596 of 1007

RESTRAINT SYSTEMS
REPAIRS 75-15
Air bag - fascia - passenger - from 04MY
$% 76.74.02
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
WARNING: When removing, testing or
installing an airbag module, do not lean
directly over it.
1.Make the SRS system safe.
+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove 2 screws securing airbag module to
fascia.
3.Release 4 clips securing airbag lower finisher.
4.Remove airbag lower finisher.5.Remove 4 screws securing lower finisher
bracket.
6.Remove 3 bolts securing airbag module to
fascia.
7.Release airbag from fascia.
CAUTION: Do not allow the airbag module
to hang by the airbag harness.
M76 4691
Page 597 of 1007

RESTRAINT SYSTEMS
75-16 REPAIRS
8.Disconnect SRS connector from airbag
module.
9.Remove airbag module.
WARNING: Store the airbag module with the
deployment side uppermost. If it is stored
deployment side down, accidental
deployment will propel the airbag module
with enough force to cause serious injury.
Refit
1.Position airbag module and connect SRS
connector to airbag module.
NOTE: If the airbag module is to be replaced,
the bar code of the new module must be
recorded.
2.Fit airbag to fascia and tighten Torx screws to
10 Nm (7 lbf.ft).
3.Align lower finisher to bracket.
4.Fit 4 screws securing lower finisher bracket.
5.Fit and secure lower finisher clips
6.Fit 2 screws securing airbag module to fascia.
7.Connect battery leads, earth lead last.
Diagnostic control unit (DCU)
$% 76.74.06
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
1.Make the SRS system safe.
+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove heater assembly.
+ HEATING AND VENTILATION,
REPAIRS, Heater unit.
3.Disconnect multiplug from DCU.
4.Remove 3 Torx bolts securing DCU to body and
remove DCU. Discard Torx bolts.
Refit
1.Fit DCU to body and secure with new bolts.
Tighten bolts to 9 Nm (7 lbf.ft).
2.Connect multiplug to DCU.
3.Fit heater assembly.
+ HEATING AND VENTILATION,
REPAIRS, Heater unit.
4.Connect battery leads, earth lead last.
Page 598 of 1007

RESTRAINT SYSTEMS
REPAIRS 75-17
Airbag - passenger - deployment - off
vehicle
$% 76.74.18
These guidelines are written to aid authorised
personnel to carry out the safe disposal of airbag
modules when removed from the vehicle.
Deploy
WARNING: It is imperative that before any
work is undertaken on the SRS system, the
appropriate information is read thoroughly.
1.Make the SRS system safe.
+ GENERAL INFORMATION, SRS
component manual deployment.
2.Remove passenger airbag from vehicle.
+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - fascia - passenger - up to 04MY.
3.Check condition of deployment tool LRT-86-
003 and associated fly leads.
4.Position LRT-86-007/02 in vice, ensuring that
vice jaws grip tool above the bottom flange to
prevent possibility of tool being forced upwards
during detonation. Tighten vice.
5.Fit and secure 2 off LRT-86-007/05 to LRT-86-
007/02.
M76 4619
LRT-86-007/05
LRT-86-007/02
Page 599 of 1007

RESTRAINT SYSTEMS
75-18 REPAIRS
6.Fit and secure airbag to LRT-86-007/05.
7.Connect deployment tool fly lead LRT-86-003/
08 to airbag.
8.Connect deployment tool LRT-86-003 to
deployment tool fly lead LRT-86-003/08.
9.Connect deployment tool LRT-86-003 to
battery.
WARNING: Ensure all personnel are at least
15 metres (50 feet) away from the airbag
module.
10.Press deployment tool operating button to
deploy airbag module.
11.Disconnect deployment tool from battery.
WARNING: During deployment parts of the
airbag module become hot enough to burn
you. Wait 30 minutes after deployment
before touching the airbag module.
12.Disconnect deployment tool fly lead from
airbag.
13.Remove airbag module from holding tools and
place in a sealed bag, ready for disposal.
14.Wipe down holding tools with a damp cloth and
remove from vice.
15.Transport deployed airbag module to
designated area for incineration.
NOTE: Do not transport deployed SRS
components in the vehicle passenger
compartment.16. Do not re-use or salvage any parts of the
SRS system.
Page 601 of 1007

RESTRAINT SYSTEMS
75-20 REPAIRS
Airbag module - steering wheel -
deployment - off vehicle
$% 76.74.16
These guidelines are written to aid authorised
personnel to carry out the safe disposal of airbag
modules when removed from the vehicle.
Deploy
WARNING: It is imperative that before any
work is undertaken on the SRS system, the
appropriate information is read thoroughly.
1.Make the SRS system safe.
+ GENERAL INFORMATION, SRS
component manual deployment.
2.Remove airbag module from steering wheel.
+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
3.Check condition of deployment tool LRT-86-
003 and associated flyleads.
4.Position toolLRT-86–007–02 in vice, ensuring
that vice jaws grip tool above bottom flange to
prevent possibility of tool being forced upwards
from vice. Tighten vice.
5.Secure airbag module to tool LRT-86–007–02
using both fixings LRT-86–007–05.
6.Ensure airbag module mounting brackets are
secure.
WARNING: Ensure the deployment tool is
not connected to the battery.7.Connect deployment tool flylead LRT-86–003–
08 to driver airbag module.
8.Connect deployment tool flylead LRT-86–003–
08 to deployment tool LRT-86–003.
9.Connect tool LRT-86–003 to battery.
WARNING: Ensure all personnel are at least
15 metres (50 ft) away from the airbag
module.
Page 602 of 1007

RESTRAINT SYSTEMS
REPAIRS 75-21
10.Press deployment tool operating button to
deploy airbag module.
WARNING: During deployment parts of the
airbag module become hot enough to burn
you. Wait 30 minutes after deployment
before touching the airbag module.
11.Disconnect deployment tool flylead LRT-86–
003–08 from driver airbag module.
12.Using gloves and face mask, remove airbag
module from tool LRT-86–007–02, place airbag
module in plastic bag and seal bag.
13.Wipe down tool with damp cloth.
14.Transport deployed airbag module to
designated area for incineration.
NOTE: Do not transport deployed SRS
components in the vehicle passenger
compartment.
15.DO NOT re-use or salvage any parts of the
SRS system including steering wheel or
steering column.
Airbag module - steering wheel -
deployment - in-vehicle
$% 76.74.15
These guidelines are written to aid authorised
personnel to carry out the safe deployment and
disposal of airbag modules when still fitted to the
vehicle.
Deploy
WARNING: It is imperative that before any
work is undertaken on the SRS system, the
appropriate information is read thoroughly.
1.Make the SRS system safe.
+ GENERAL INFORMATION, SRS
component manual deployment.
2.Check condition of deployment tool LRT-86–
003and associated flyleads.
3.Remove steering column nacelle.
4.Disconnect SRS harness connector from back
of rotary coupler.
WARNING: Ensure airbag module is secure
within steering wheel.
WARNING: Ensure the deployment tool is
not connected to the battery.
Page 603 of 1007

RESTRAINT SYSTEMS
75-22 REPAIRS
5.Connect deployment tool flylead LRT-86–003–
01 to back of rotary coupler.
6.Connect deployment tool flylead LRT-86–003–
01 to deployment tool LRT-86–003.
7.Connect tool LRT-86–003 to battery.
WARNING: Ensure all personnel are at least
15 metres (50 ft) away from the vehicle.
8.Press deployment tool operating button to
deploy airbag module.
WARNING: During deployment parts of the
airbag module become hot enough to burn
you. Wait 30 minutes after deployment
before touching the airbag module.9.Disconnect deployment tool flylead LRT-86–
003–01 from back of rotary coupler.
10.Using gloves and face mask, remove airbag
module from steering wheel.
+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
11.Place airbag module in plastic bag and seal
bag.
12.Transport deployed airbag module to
designated area for incineration.
NOTE: Do not transport deployed SRS
components in the vehicle passenger
compartment.
13.DO NOT re-use or salvage any parts of the
SRS system including steering wheel or
steering column.
Page 605 of 1007

RESTRAINT SYSTEMS
75-24 REPAIRS
8.Press deployment tool operating button to
deploy airbag module.
WARNING: A deployed airbag or seatbelt
pre-tensioner is very hot, DO NOT return to
a deployed airbag module until at least 30
minutes have elapsed since deployment.
9.Disconnect flylead LRT-86–003–04 from pre-
tensioner connector and remove pre-tensioner
from seat.
+ RESTRAINT SYSTEMS, REPAIRS,
Pre-tensioner - seat belt - front.
10.Place pre-tensioner in plastic bag and seal bag.
11.Transport deployed pre-tensioner to
designated area for incineration.
NOTE: Do not transport deployed SRS
components in the vehicle passenger
compartment.
12.Scrap all remaining parts of the seat belt and
SRS system. DO NOT re-use or salvage any
parts of the seat belt and SRS system.
Page 675 of 1007

INTERIOR TRIM COMPONENTS
76-3-14 REPAIRS
Fascia - up to 04MY
$% 76.46.23
Remove
1.Remove front console.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.
2.Remove rotary coupler.
+ RESTRAINT SYSTEMS, REPAIRS,
Rotary coupler - (SRS) air bag system.
3.Disconnect 4 multiplugs from wiper/indicator
switch.
4.Loosen clamping screw and remove wiper/
indicator switch.
5.Remove 2 screws from steering column lower
finisher and remove finisher.6.Open drivers glove box lid and remove fuse box
cover.
7.Disconnect 2 multiplugs from fusebox.
8.Close glove box.
9.Remove clock.
+ INSTRUMENTS, REPAIRS, Clock.
10.Remove both 'A' post upper trim finishers.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
11. Models without passenger airbag: Remove
fascia stowage box.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Stowage box - fascia.
12. Models with passenger airbag: Remove
passenger airbag.
+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - fascia - passenger - up to 04MY.
Page 678 of 1007

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-17
26. Models without passenger airbag: Remove 4
nuts from grab handle and remove handle.
27.Remove 4 screws from centre bracket and
remove bracket.28.Remove 4 face level vents and collect seals.
29.Remove glove box hinge pins and remove
glove box lids.
30.Remove glove box lamp and mat.
31.Remove 4 screws from glove box and remove
glove box.
32.Remove 2 screws from each glove box lock and
remove locks.
33.Remove switch blank.
34.Disconnect multiplug from immobilisation ECU.
35.Remove 2 nuts securing immobilisation ECU to
fascia and remove ECU.
36.Remove fascia and coin tray mats.
M76 3995