exhaust LAND ROVER FREELANDER 2001 Owner's Manual

TORQUE WRENCH SETTINGS
06-14
Cooling System – Td4
Cooling System – K1.8
Cooling System – KV6
†Tighten in sequence.
+ Apply sealant, Part No. STC 50552 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant hose adaptor to cylinder head bolts 8 Nm 6 lbf.ft
Coolant rail (lower) to sump bolts 10 Nm 7.5 lbf.ft
Coolant rail to cylinder head bolt 20 Nm 15 lbf.ft
Coolant rail to exhaust manifold bolt 20 Nm 15 lbf.ft
Coolant pump to cylinder block bolts 10 Nm 7.5 lbf.ft
Fan and motor assembly to fan cowl bolts 5 Nm 4 lbf.ft
Fan cowl to radiator bolts 5 Nm 4 lbf.ft
Fuel cooler to mounting nuts 10 Nm 7.5 lbf.ft
Fuel rail to coolant rail bolt 10 Nm 7.5 lbf.ft
Heatshield to coolant rail Allen screws 8 Nm 6 lbf.ft
Thermostat housing to coolant pump bolts 8 Nm 6 lbf.ft
Upper coolant rail to thermostat housing bolt 8 Nm 6 lbf.ft
TORQUE DESCRIPTION METRIC IMPERIAL
Condenser to radiator bolts 3 Nm 2.2 lbf.ft
Cooling fan control unit mounting bolt 5 Nm 4 lbf.ft
Cooling fan cowl to radiator 5 Nm 4 lbf.ft
Cooling fan and motor assembly to cowl bolts 5 Nm 4 lbf.ft
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant pump to cylinder block bolts
†9 Nm 6.5 lbf.ft
Cooling fan and motor assembly to fan cowl bolts 5 Nm 3.7 lbf.ft
Cooling fan cowl to radiator bolts 5 Nm 3.7 lbf.ft
Cylinder block drain plug
+20 Nm 15 lbf.ft
Injector protection cover to RH fuel rail and inlet manifold bolts 9 Nm 6.5 lbf.ft
Radiator baffle bolts 5 Nm 3.7 lbf.ft
Thermostat housing flange / coolant elbow bolt 18 Nm 13 lbf.ft

TORQUE WRENCH SETTINGS
06-15
Manifolds and Exhaust System – Td4
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant rail to cylinder head bolt 20 Nm 15 lbf.ft
Coolant rail to exhaust manifold bolt 20 Nm 15 lbf.ft
Coolant rail to thermostat housing bolt 8 Nm 6 lbf.ft
EGR cooler to cylinder head and lifting bracket bolts 25 Nm 18 lbf.ft
EGR pipe clamp screw 10 Nm 7.5 lbf.ft
EGR pipe to cylinder head bolt 20 Nm 15 lbf.ft
EGR pipe to manifold Torx screws 22 Nm 16 lbf.ft
Exhaust manifold to cylinder head nuts 24 Nm 18 lbf.ft
Front pipe clamping plate nuts 50 Nm 37 lbf.ft
Front pipe to intermediate pipe flange nuts 60 Nm 44 lbf.ft
Fuel rail to coolant rail bolt 10 Nm 7.5 lbf.ft
Fuel rail to support bracket bolt 10 Nm 7.5 lbf.ft
Heat shield to coolant rail Allen screws 8 Nm 6 lbf.ft
Inlet manifold:
⇒ M6 bolts10 Nm 7.5 lbf.ft
⇒ M7 bolts and nuts 15 Nm 11 lbf.ft
Intermediate pipe to tail pipe flange nuts 60 Nm 44 lbf.ft
Tail pipe clamp nut 55 Nm 41 lbf.ft
Turbocharger to exhaust manifold bolts 50 Nm 37 lbf.ft
Turbocharger outlet pipe bolts:
⇒6 mm10 Nm 7.5 lbf.ft
⇒8 mm25 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-16
Manifolds and Exhaust Systems – K1.8
†Tighten in sequence.
TORQUE DESCRIPTION METRIC IMPERIAL
Alternator bolts45 Nm 33 lbf.ft
Alternator mounting bracket bolts 25 Nm 18 lbf.ft
Coil cover bolts10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold bolts 10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold nut 25 Nm 18 lbf.ft
Exhaust front pipe to intermediate pipe nuts 60 Nm 44 lbf.ft
Exhaust front pipe to manifold nuts 60 Nm 44 lbf.ft
Exhaust manifold to cylinder head nuts
†45 Nm 33 lbf.ft
Exhaust manifold heatshield to front pipe bolts 9 Nm 7 lbf.ft
Heated Oxygen (HO
2S) Sensor 55 Nm 41 lbf.ft
Heatshield to alternator bracket:
⇒ Nut25 Nm 18 lbf.ft
⇒ Bolts10 Nm 7.5 lbf.ft
Inlet manifold to cylinder head nuts
†17 Nm 12.5 lbf.ft
Intermediate pipe to tail pipe flange nuts 60 Nm 44 lbf.ft
RH coil bolts10 Nm 7.5 lbf.ft
Tail pipe clamp nut 55 Nm 41 lbf.ft

TORQUE WRENCH SETTINGS
06-17
Manifolds and Exhaust Systems – KV6
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant/breather hose bracket to inlet manifold bolt 9 Nm 6.5 lbf.ft
Exhaust heatshield to exhaust mounting bracket bolts 45 Nm 33 lbf.ft
Exhaust heatshield to IRD housing nut 45 Nm 33 lbf.ft
Exhaust heatshield to lower engine steady mounting bracket bolts 9 Nm 6.5 lbf.ft
Exhaust heatshield to pinion housing nuts 25 Nm 18 lbf.ft
Exhaust flange (LH) to front pipe nuts 50 Nm 37 lbf.ft
Exhaust flange (LH) to front pipe nuts 50 Nm 37 lbf.ft
Exhaust manifold to cylinder head nuts 45 Nm 33 lbf.ft
Exhaust front pipe to manifold flange nuts 50 Nm 37 lbf.ft
Heated Oxygen (HO
2S) sensor 55 Nm 41 lbf.ft
Inlet manifold chamber to inlet manifold bolts 18 Nm 13 lbf.ft
Inlet manifold chamber support brackets to RH camshaft cover bolts 10 Nm 7.5 lbf.ft
Inlet manifold to cylinder head nuts and bolts 25 Nm 18 lbf.ft
Intermediate pipe to front pipe nuts 50 Nm 37 lbf.ft
Intermediate pipe to front pipe nuts 50 Nm 44 lbf.ft
Lower engine steady to subframe bolt 100 Nm 74 lbf.ft
Lower engine steady to sump mounting bolt 100 Nm 74 lbf.ft
RH upper engine steady to body bolt 100 Nm 74 lbf.ft
RH upper engine steady to top arm bolt 100 Nm 74 lbf.ft
Tail pipe clamp nuts 55 Nm 41 lbf.ft

TORQUE WRENCH SETTINGS
06-21
Intermediate Reduction Drive
+ Apply sealant, Part No. STC 4600 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Drain plug35 Nm 26 lbf.ft
Exhaust heatshield to exhaust mounting bracket 45 Nm 33 lbf.ft
Exhaust heatshield to IRD screws (Td4) 30 Nm 22 lbf.ft
Exhaust heatshield to IRD nut (K1.8 and KV6) 45 Nm 33 lbf.ft
Filler / level plug35 Nm 26 lbf.ft
IRD unit to gearbox bolts 90 Nm 66 lbf.ft
IRD end cover bolts
+30 Nm 22 lbf.ft
IRD support bracket to cylinder block bolt (K1.8) 48 Nm 35 lbf.ft
IRD support bracket to cylinder block bolt (K1.8) 48 Nm 35 lbf.ft
IRD support bracket to IRD bolts (Td4)
⇒ M8
⇒ M1030 Nm
50 Nm22 lbf.ft
37 lbf.ft
IRD support bracket to IRD bolts (K1.8 and KV6) 50 Nm 37 lbf.ft
IRD support bracket to sump (K1.8 and KV6) 88 Nm 65 lbf.ft
Lower engine steady to IRD support bracket bolts 100 Nm 74 lbf.ft
Manifold heatshield to IRD support bracket bolts (K1.8 and KV6) 9 Nm 6.5 lbf.ft
Manifold heatshield to IRD support bracket bolts (K1.8 and KV6) 25 Nm 18 lbf.ft
Manifold heatshield to pinion housing nut (KV6) 45 Nm 33 lbf.ft
Manifold heatshield to IRD (Td4) 30 Nm 22 lbf.ft
Breather pipe bracket screw 9 Nm 7 lbf.ft
Mass damper to pinion housing nuts (K1.8) 25 Nm 18 lbf.ft
Pinion nut150 Nm 111 lbf.ft
Pinion housing nuts 25 Nm 18 lbf.ft
Propeller shaft to IRD flange bolts 40 Nm 30 lbf.ft

TORQUE WRENCH SETTINGS
06-32
Heating and Ventilation
TORQUE DESCRIPTION METRIC IMPERIAL
Air intake hose and bracket assembly to fuel burning heater bolts (Td4) 10 Nm 7.5 lbf.ft
Exhaust pipe clamp bolts (Td4) 5 Nm 3.5 lbf.ft
Fuel burning heater to body bolts (Td4) 8 Nm 6 lbf.ft
Fuel burning heater to mounting bracket bolts (Td4) 8 Nm 6 lbf.ft
Heater to fascia nuts 8 Nm 6 lbf.ft
Heater to bulkhead bolt 8 Nm 6 lbf.ft
Evaporator to bulkhead bolts 8 Nm 6 lbf.ft

LIFTING AND TOWING
08-1
LIFTING AND TOWING
Jacking
The following instructions must be carried out before
raising the vehicle off the ground:
lUse a solid level surface.
lApply parking brake.
lSelect 1st. gear in main gearbox and ensure
HDC is not selected.
CAUTION: To avoid damage to under body
components of the vehicle, adhere to the
following jacking procedures:
DO NOT POSITION JACKS OR AXLE STANDS
UNDER THE FOLLOWING COMPONENTS:
lBumpers
lBrake or Fuel lines
lExhaust pipe
lSuspension components
lSteering rack and linkages
lFuel tank
lEngine sump
lGearbox
lIRD unit
Jack or support vehicle only on approved jacking
points as detailed in the following illustration:
Front (hydraulic jack) and side (vehicle jack) jacking
pointsSafety stand positions under longitudinal members
Rear (hydraulic jack) and side (vehicle jack) jacking
points
Vehicle jack
The jack provided with the vehicle is only intended to
be used in an emergency, for changing a tyre. Do
NOT use the jack for any other purpose. Refer to the
Owner's Handbook for vehicle jack location points
and procedure. Never work under a vehicle only
supported by the vehicle jack.
Hydraulic jack
A hydraulic jack with a minimum 1500 kg (3,300 lbs)
load capacity must be used.
WARNING: Do not work on or under a vehicle
supported only by a jack. Always support the
vehicle on safety stands.

MAINTENANCE
10-26 MAINTENANCE
KV6 – Petrol engines
Check
1.Check security of all fuel hoses, paying
particular attention to those running under the
vehicle. Check all hoses and pipes are correctly
routed and secured. Check for signs of leakage
or damage.
Brake Hoses and Pipes
Check
1.Visually check condition of all brake hoses.
Look for any sign of damage or chafing. Check
for any signs of fluid leakage.
2.Check brake pipes for signs of leakage or
corrosion. Pay particular attention to pipe
unions and joints. Ensure all pipes and hoses
are correctly routed and secured.
Check Exhaust System
Check
1.Visually check condition of exhaust system for
signs of damage. Extra care should be taken to
ensure the catalyst is in good condition and
shows no signs of damage. Check condition of
exhaust heat shields.
2.Check exhaust system is firmly secured and
check condition of exhaust mounting rubbers,
clamps and brackets.

ENGINE - K SERIES KV6
REPAIRS 12-3-3
REPAIRS
Camshafts - LH cylinder head
$% 12.13.02
Remove
1.Disconnect battery earth lead.
2.Remove camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
3.Remove LH camshaft rear timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft rear timing belt - LH cylinder
head.
4.Remove LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
5.Remove 4 bolts and remove front camshaft
drive belt cover backplate from cylinder head.
6.Remove 2 bolts securing LH rear camshaft
drive belt cover backplate to cylinder head and
remove backplate.7.Using sequence shown, progressively loosen
22 bolts securing camshaft carrier to cylinder
head until valve spring pressure is released,
remove bolts.
8.Release camshaft carrier from dowels and
remove carrier.
9.Remove camshafts and discard oil seals.
10.Using a stick magnet, remove 12 hydraulic
tappets from cylinder head.
CAUTION: Store hydraulic tappets in their
fitted order and store upright. Maintain
absolute cleanliness when handling
hydraulic tappets. Failure to observe these
precautions can result in engine failure.
11.Clean camshafts and bearing running surfaces
in camshaft carrier and cylinder head.
12.Inspect camshafts and replace camshafts if
scored, pitted or excessively worn.
Note: Camshafts are colour coded - Inlet -
ORANGE; Exhaust - BLUE.
M12 6905
M12 6906

ENGINE - K SERIES KV6
12-3-4 REPAIRS
Refit
1.Thoroughly clean and lubricate hydraulic
tappets with clean engine oil. Fit hydraulic
tappets to original bores in cylinder head.
2.Ensure that mating faces of camshaft carrier
and cylinder head are clean and dry.
3.Lubricate camshafts and bearing journals with
clean engine oil.
4.Position camshafts in cylinder head with rear
timing gear drive slots in each camshaft facing
towards the centre as shown.
CAUTION: Ensure camshafts are in their
correct fitted locations, camshafts are
colour coded - Inlet - ORANGE; Exhaust -
BLUE.
5.Apply continuous thin beads of sealant, Part
No. STC 4600, to paths on camshaft carrier as
shown. Spread sealant to an even film using a
roller.
CAUTION: Ensure sealant does not enter oil
feed holes or grooves and that assembly is
completed within 20 minutes.6.Position camshaft carrier, fit and progressively
tighten bolts in the sequence shown to 10 Nm
(7.5 lbf.ft).
7.Noting that the front camshaft oil seals are
black in colour and the rear oil seals are red, fit
new camshaft oil seals using LRT-12-203 and
LRT-12-148A
CAUTION: Oil seals must be fitted dry. Do
not use tool LRT-12-148 for fitting seals.
8.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.
9.Position camshaft timing belt rear cover
backplates to cylinder head, fit and tighten bolts
to 9 Nm (7 lbf.ft).
10.Fit LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
11.Fit camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.