drive belt LAND ROVER FREELANDER 2001 Repair Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 2001, Model line: FREELANDER, Model: LAND ROVER FREELANDER 2001Pages: 1007, PDF Size: 23.47 MB
Page 505 of 1007
STEERING
57-12 REPAIRS
Pump - steering - KV6
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Remove engine mounting top arm.
+ ENGINE - K SERIES KV6, REPAIRS,
Arm assembly - engine mounting RH.
3.Loosen PAS pump pulley bolts.
4.Using a 3/8" socket bar, raise ancillary drive
belt tensioner and release drive belt from
alternator and PAS pump pulleys.
5.Position container to collect PAS fluid spillage.6.Release clip and disconnect fluid inlet hose
from PAS pump.
7.Remove banjo bolt securing fluid outlet hose to
PAS pump, release hose, remove and discard
sealing washers.
CAUTION: To prevent damage to
components, use two spanners when
loosening or tightening unions.
8.Remove bolt securing PAS outlet pipe support
bracket to cylinder head and move pipe aside.
9.Remove 3 bolts securing PAS pump pulley to
PAS pump and remove pulley.
CAUTION: Always fit plugs to open
connections to prevent contamination.
Page 506 of 1007
STEERING
REPAIRS 57-13
10.Remove 3 bolts securing PAS pump to
mounting bracket.
11.Remove PAS pump.Refit
1.Position PAS pump and align to mounting
bracket.
2.Fit bolts securing PAS pump to mounting
bracket and tighten to 25 Nm (18 lbf.ft).
3.Fit PAS pump pulley to PAS pump and tighten
bolts to finger tight.
4.Remove plug from fluid outlet hose.
5.Clean banjo bolt and mating faces.
6.Using new sealing washers, fit PAS outlet hose
to pump and tighten banjo bolt to 20 Nm (15
lbf.ft).
CAUTION: To prevent damage to
components, use two spanners when
loosening or tightening unions.
7.Align outlet pipe clip. Fit bolt and tighten to 22
Nm (16 lbf.ft).
8.Clean elbow on PAS pump.
9.Remove plug from fluid inlet hose, fit new clip
and connect hose to PAS pump.
10.Remove container.
11.Clean pulley 'V's and tensioner pulley running
surface.
12.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
13.Tighten PAS pump pulley bolts to 10 Nm (7.5
lbf.ft).
14.Fit engine mounting top arm.
+ ENGINE - K SERIES KV6, REPAIRS,
Arm assembly - engine mounting RH.
15.Connect battery earth lead.
16.Bleed PAS system.
+ STEERING, ADJUSTMENTS, Power
assisted steering (PAS) system - bleed.
Page 507 of 1007
STEERING
57-14 REPAIRS
Pump - steering - K1.8
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Loosen PAS pump pulley bolts.
4.Remove PAS pump drive belt.
+ STEERING, REPAIRS, Drive belt -
K1.8.
5.Position container to collect PAS fluid spillage.
6.Release clip and disconnect fluid inlet hose
from PAS pump.
CAUTION: Always fit plugs to open
connections to prevent contamination.
7.Loosen union securing fluid outlet pipe, release
outlet pipe remove and discard 'O' ring.
8.Remove 3 bolts securing PAS pump pulley to
PAS pump and remove pulley.9.Remove 5 bolts securing PAS pump to
mounting bracket.
10.Remove PAS pump.
Refit
1.Position PAS pump and align to mounting
bracket.
2.Fit bolts securing PAS pump to mounting
bracket and tighten to 25 Nm (18 lbf.ft).
3.Fit PAS pump pulley and align bolts holes.
Ensure FRONT mark is facing outwards. Fit
bolts finger tight.
4.Remove plug from fluid outlet hose.
5.Clean PAS pump and pipe union.
6.Using a new 'O' ring, align outlet pipe and
tighten union to 20 Nm (15 lbf.ft).
7.Clean elbow on PAS pump.
8.Remove plug from fluid inlet hose, fit new clip
and connect hose to PAS pump.
9.Remove container.
10.Clean pulley 'V's and tensioner pulley running
surface.
11.Fit PAS pump drive belt.
+ STEERING, REPAIRS, Drive belt -
K1.8.
12.Tighten PAS pump pulley bolts to 10 Nm (7.5
lbf.ft).
13.Connect battery earth lead.
14.Bleed PAS system.
+ STEERING, ADJUSTMENTS, Power
assisted steering (PAS) system - bleed.
M57 1069
M57 1070
Page 508 of 1007
STEERING
REPAIRS 57-15
Pump - steering - Td4
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Remove hydramount.
+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
3.Loosen 3 PAS pump pulley bolts.
4.Remove ancillary drive belt.
+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
5.Raise engine on hoist.
6.Remove bolts and remove PAS pump pulley.
7.Cover alternator to prevent PAS oil
contamination.
8.Place container beneath PAS pump, release
clip and remove feed hose to pump. Allow fluid
to drain.
CAUTION: Care must be taken to ensure
that oil or fluid does not enter or
contaminate the alternator.9.Remove banjo bolt securing fluid outlet hose to
PAS pump, release hose, remove and discard
sealing washers.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
10.Remove 4 bolts and remove PAS pump.
11.Remove 5 Torx bolts securing PAS pump to
mounting brackets. Collect mounting brackets.
Refit
1.Position PAS pump to mounting brackets, fit
and tighten Torx bolts to 25 Nm (18 lbf.ft).
2.Position pump to mounting, fit bolts and tighten
M8 bolts to 25 Nm (18 lbf.ft) and M6 bolts to 10
Nm (7.5 lbf.ft).
3.Using new sealing washers, fit PAS outlet hose
to pump and tighten banjo bolt to 25 Nm (18
lbf.ft).
4.Clean PAS pump and mating faces.
5.Fit inlet hose to PAS pump and secure with new
clip.
6.Fit PAS pump pulley to PAS pump and tighten
bolts to finger tight.
7.Fit ancillary drive belt.
+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
8.Tighten PAS pump pulley bolts to 10 Nm (7.5
lbf.ft).
9.Fit hydramount.
+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
10.Connect battery earth lead.
Page 890 of 1007
AIR CONDITIONING
ADJUSTMENTS 82-3
ADJUST ME NTS
Drive belt - compressor - Td4
$% 82.10.01
Check
1.Disconnect battery earth lead.
2.Remove underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Turn steering on RH lock.
4.Remove 3 bolts and RH splash shield.
5.Check condition of drive belt. Renew a drive
belt that shows signs of wear and splitting.Adjust
1.Loosen clamp and pivot bolts of compressor
drive belt tensioner.
2.Apply an anti-clockwise torque of 38 Nm (28
lbf.ft) for an existing belt and 47 Nm (35 lbf.ft)
for a new belt to tensioner plate hexagon.
3.Tighten tensioner clamp bolt to 24 Nm (18
lbf.ft).
4.Tighten tensioner pivot bolt to 24 Nm (18 lbf.ft).
5.Fit splash shield and tighten bolts to 10 Nm (7.5
lbf.ft).
6.Fit underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
7.Connect battery earth lead.
M82 0721
Page 892 of 1007
AIR CONDITIONING
REPAIRS 82-5
REPAIRS
Drive belt - compressor - Td4
$% 82.10.02
Remove
1.Disconnect battery earth lead.
2.Remove ancillary drive belt.
+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
3.Loosen clamp and pivot bolts of compressor
drive belt tensioner.
4.Remove compressor drive belt.Refit
1.Ensure compressor drive belt and compressor,
crankshaft and tensioner pulleys are clean.
2.Fit compressor drive belt.
3.Adjust compressor drive belt.
+ AIR CONDITIONING,
ADJUSTMENTS, Drive belt - compressor -
Td4.
4.Fit ancillary drive belt.
+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
5.Connect battery earth lead.
M82 0721
Page 893 of 1007
AIR CONDITIONING
82-6REPAIRS
Compressor - Td4
$% 82.10.20
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Disconnect battery earth lead.
3.Recover refrigerant from A/C system.
+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
4.Remove compressor drive belt.
+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
WARNING: Under no circumstances should
refrigerant hoses be disconnected without
first discharging the system.
5.Remove 2 bolts securing A/C pipes to
compressor. Release pipes from compressor.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
6.Remove and discard 'O' rings from A/C pipes.7.Loosen bolt securing compressor support
bracket to sump, do not remove.
8.Remove 3 bolts and remove compressor from
mounting bracket. Move support strap aside,
disconnect compressor multiplug and remove
compressor.
Refit
1.If a new compressor is being installed, drain the
required amount of refrigerant oil from the new
compressor.
+ GENERAL INFORMATION, Air
conditioning compressor replacement.
2.A new compressor is sealed and pressurised
with Nitrogen gas, slowly release the sealing
cap, gas pressure should be heard to release
as the seal is broken.
3.Ensure mating faces of A/C pipes and
compressor are clean.
4.Fit A/C compressor to mounting bracket, align
support strap and tighten bolts to 25 Nm (18
lbf.ft).
5.Connect multiplug to compressor.
6.Lubricate new 'O' rings with clean refrigerant oil
and fit to evaporator pipes
7.Position A/C pipes to compressor, fit bolts and
tighten to 22 Nm (16 lbf.ft).
8.Replace receiver drier.
+ AIR CONDITIONING, REPAIRS,
Receiver drier.
9.Fit compressor drive belt.
+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
10.Recharge A/C system.
+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
11.Connect battery earth lead.
12.Remove stands and lower vehicle.
Page 894 of 1007
AIR CONDITIONING
REPAIRS 82-7
Compressor - KV6
$% 82.10.20
Remove
1.Disconnect battery earth lead.
2.Recover refrigerant from A/C system.
+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
3.Remove underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Remove RH front road wheel.
5.Remove 3 bolts securing RH splash shield to
body and remove shield.
6.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and release drive
belt from A/C compressor pulley.7.Remove 2 bolts securing high and low pressure
pipes to compressor. Release pipes from
compressor, remove and discard 'O' rings.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
8.Disconnect multiplug from compressor.
9.Note fitted position of heat shield on
compressor and remove 3 bolts securing
compressor to front mounting plate and
cylinder block. Remove compressor and heat
shield.
M12 6614
Page 895 of 1007
AIR CONDITIONING
82-8REPAIRS
Refit
1.If a new compressor is being installed, drain the
required amount of refrigerant oil from the new
compressor.
+ GENERAL INFORMATION, Air
conditioning compressor replacement.
2.A new compressor is sealed and pressurised
with Nitrogen gas, slowly release the sealing
cap, gas pressure should be heard to release
as the seal is broken.
3.Clean compressor and mating face on front
mounting plate and cylinder block.
4.Position compressor, fit but do not fully tighten
lower bolt.
5.Position heat shield and fit compressor upper
securing bolts. Tighten compressor upper and
lower securing bolts to 25 Nm (18 lbf.ft).
6.Remove caps from compressor and high
pressure pipe.
7.Clean compressor high pressure pipe
connection.
8.Lubricate new 'O' ring with refrigerant oil and fit
to high pressure pipe.
9.Connect high pressure pipe to compressor, fit
and tighten bolt to 25 Nm (18 lbf.ft).
10.Connect multiplug to compressor.
11.Remove caps from compressor and low
pressure pipe.
12.Clean compressor low pressure pipe
connection.
13.Lubricate new 'O' ring with refrigerant oil and fit
to low pressure pipe.
14.Connect low pressure pipe to compressor, fit
and tighten bolt to 25 Nm (18 lbf.ft).
15.Clean pulley 'V's and tensioner pulley running
surface.
16.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
17.Fit splash shield and secure with bolts.
18.Fit RH road wheel and tighten nuts to 115 Nm
85 lbf.ft).
19.Replace receiver drier.
+ AIR CONDITIONING, REPAIRS,
Receiver drier.
20.Recharge A/C system.
+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
21.Connect battery earth lead.
22.Fit underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
Compressor - K1.8
$% 82.10.20
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Recover refrigerant from A/C system.
+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
5.Remove alternator.
+ CHARGING AND STARTING,
REPAIRS, Alternator - K1.8.
6.Disconnect multiplug from compressor.
7.Remove 2 bolts securing A/C pipes to
compressor, release A/C pipes from
compressor.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
8.Remove and discard 'O' rings from A/C pipes.
M82 0730
Page 914 of 1007
CHARGING AND STARTING
ADJUSTMENTS 86-1-1
CHARGING AND STARTING ADJUST ME NTS
Ancillary drive belt - K1.8
$% 86.10.05
Check
1.Disconnect battery earth lead.
2.Turn steering on RH lock.
3.Remove 3 bolts and remove splash shield.
4.Rotate crankshaft a sufficient number of turns
to check condition of drive belt. Renew a drive
belt that shows signs of wear, splitting or oil
contamination.
5.Apply a force of 10 kg to drive belt at position 'X'
and measure deflection between crankshaft
pulley and alternator pulley. Deflection must be
6 - 8 mm.Adjust
1.Loosen alternator pivot nut and bolt.
2.Loosen bolt securing alternator adjustment
bracket to engine.
3.Loosen bolt securing alternator to adjustment
bracket.
4.Increase drive belt tension by rotating
alternator adjustment bolt clockwise.
5.Tighten alternator pivot and adjustment bracket
bolts to 25 Nm (18 lbf.ft).
6.Recheck drive belt tension.
7.Fit splash shield and secure with bolts.
8.Straighten steering.
9.Connect battery earth lead.