fold seats LAND ROVER FREELANDER 2001 Workshop Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 2001, Model line: FREELANDER, Model: LAND ROVER FREELANDER 2001Pages: 1007, PDF Size: 23.47 MB
Page 210 of 1007
ENGINE - K SERIES KV6
REPAIRS 12-3-33
71.Remove 3 bolts securing PAS pump to front
mounting plate and tie pump aside.
72.With assistance, manoeuvre and lower engine
and gearbox to floor.
Refit
1.With assistance, raise engine and gearbox into
engine compartment.
2.Position PAS pump to front mounting plate, fit
and tighten bolts to 25 Nm (18 lbf.ft).
3.Position PAS pump pulley, fit and tighten Torx
screws to 9 Nm (7 lbf.ft).
4.Position top arm to engine mounting bracket
and RH hydramount, fit and tighten bolts to 100
Nm (74 lbf.ft).
5.Position PAS pipe support bracket to RH
hydramount, fit and tighten nut to 85 Nm (63
lbf.ft).
6.Place a wooden block on jack, position jack
under gearbox and raise jack sufficient to
support weight of gearbox. Release lifting hook
from lifting bracket on gearbox and connect to
rear engine lifting bracket.
7.Lower and remove jack supporting gearbox.
8.Remove bolts securing LRT-44-026 lifting
bracket to gearbox and remove bracket.
9.Position LH mounting bracket to gearbox, fit
and tighten bolts to 85 Nm (63 lbf.ft).
10.Position LH mounting to body, fit and tighten
bolts to 48 Nm.
11.Align gearbox bracket to LH body mounting, fit
and tighten through bolt to 100 Nm (74 lbf.ft).
12.Position upper RH engine steady to top arm, fit
and tighten bolt to 100 Nm (74 lbf.ft).
13.Tighten bolt securing upper RH engine steady
to body to 100 Nm (74 lbf.ft).
14.Position PAS pipe to engine front mounting
plate, fit and tighten bolt to 25 Nm (18 lbf.ft).
15.Lower hoist, disconnect and remove lifting
bracket, LRT-12-138.
16.Raise vehicle on ramp.17.Position A/C compressor to front mounting
plate and cylinder block, align heat shield, fit
and tighten bolts to 25 Nm (18 lbf.ft).
18.Connect multiplug to A/C compressor.
19.Using a 3/8 square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
20.Position selector cable to gearbox bracket and
secure with clip.
21.Position selector lever to selector shaft, fit and
tighten nut to 25 Nm (18 lbf.ft).
22.Clean splines and seal areas on each
driveshaft and mating faces in front hubs.
23.Fit new circlips to RH and LH driveshaft inner
joint splines.
24.Fit driveshafts to IRD and gearbox, ensuring
that the circlip on each driveshaft is fully
engaged.
25.Engage LH and RH driveshafts into front hubs.
26.Fit new driveshaft flange nuts but do not tighten
at this stage.
27.Clean ball joint tapers and taper seats.
28.Position LH and RH track rod ends to steering
arms, fit new nuts and tighten to 55 Nm (40
lbf.ft).
29.Clean ABS sensors and mating faces.
30.Apply anti-seize grease to both ABS sensors
and position sensors in front hubs.
Ensure ABS sensor is fully located into hub,
so that sensor touches pole wheel teeth.
31.Position LH and RH brake hoses to front
damper brackets and secure with clips.
32.Position LH and RH splash shields, fit and
tighten bolts.
33.Ensure mating face of propeller shaft and IRD
drive flange are clean.
34.Fit propeller shaft to IRD flange and align
marks. Tighten nuts and bolts to 42 Nm (31
lbf.ft).
35.Fit rear beam.
+ FRONT SUSPENSION, REPAIRS,
Rear beam.
36.Fill IRD to correct level with fluid.
+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) fluid - drain & refill -
Non NAS.
+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) lubrication system -
drain & refill - NAS.
37.Fit exhaust front pipe.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Front pipe - Non
NAS.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Front pipe - NAS.
Page 588 of 1007
RESTRAINT SYSTEMS
REPAIRS 75-7
Stalk - rear seat belt - LH - 5 door
$% 76.73.32
Remove
1.Fold rear seat forward.
2.Remove 3 screws from end cover and remove
cover from seat hinge.
3.Remove 4 Torx bolts from seat lock down catch
and remove catch assembly.
4.Remove Torx bolt from seat belt buckle and
remove buckle.Refit
1.Fit buckle to catch assembly and tighten Torx
bolt to 32 Nm (24 lbf.ft).
2.Fit catch assembly to seat and tighten Torx
bolts.
3.Fit catch assembly to seat, fit Torx bolts but do
not tighten at this stage.
4.Fold seat down and check that seat unfolds on
lock down bar correctly. Adjust catch assembly
if required.
5.Tighten catch Torx bolts to 32 Nm (24 lbf.ft).
6.Recheck seat fold.
7.Fit end cover and tighten screws.
8.Reposition rear seats.
Page 663 of 1007
INTERIOR TRIM COMPONENTS
76-3-2 REPAIRS
Trim casing - rear quarter - lower - 5 door
$% 76.13.12
Remove
1.Release rear seat squab and fold seat forward.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Release load space lamp from trim casing.
4.Disconnect 2 Lucars and remove load space
lamp.
5.Remove 2 screws securing casing to load
space carpet retainer.
6.Release 4 turn buckles securing trim casing.
7.Release trim casing from 5 retaining clips.
8.Remove loadspace side trim casing.
9.Remove 5 retaining clips from trim casing.Refit
1.Fit retaining clips to casing.
2.Position casing in loadspace, locate and secure
retaining clips.
3.Fit turn buckles.
4.Fit screws securing casing to carpet retainer.
5.Position load space lamp to casing, connect
Lucars and secure lamp to casing.
6.Position loadspace cover retainer and secure
with screw.
7.Fit loadspace cover and secure in retainers.
8.Position rear seat belt and tighten bolt to 40 Nm
(29 lbf.ft).
9.Reposition rear seats.
Page 696 of 1007
SEATS
REPAIRS 76-5-1
SEATS REPAIRS
Front seat
$% 78.10.44.99
Remove
1.Make the SRS system safe.
+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove seat base finisher.
+ SEATS, REPAIRS, Finisher - seat
base - front - each.
3.Release pretensioner multiplug from seat
frame and disconnect.
4.Remove cover from rear securing bolt.
5.Remove 4 Torx screws securing seat.
6.Remove front seat.
Refit
1.Position front seat and secure with Torx
screws.Tighten screws to 45 Nm (33 lbf.ft).
2.Fit cover to rear bolt.
3.Connect pretensioner multiplug and secure to
seat frame.
4.Fit seat base finisher.
+ SEATS, REPAIRS, Finisher - seat
base - front - each.
Rear seat - LH
$% 78.10.48.99
Remove
1.Remove 2 Torx bolts from seat hinges.
2.Fold seat forward and remove 2 Torx bolts from
hinges.
3.Remove seat.
Refit
1.Position seat in vehicle and align hinges.
2.Fit Torx bolts to seat hinges and tighten to 25
Nm (18 lbf.ft).
3.Lower seat.
4.Fit Torx bolts to heel board and tighten to 25
Nm (18 lbf.ft).
Page 697 of 1007
SEATS
76-5-2 REPAIRS
Rear seat - RH
$% 78.10.49.99
Remove
1.Remove 2 Torx bolts from seat hinges.
2.Fold seat forward and remove 2 Torx bolts from
hinges.
3.Remove seat.
Refit
1.Position seat in vehicle and align hinges.
2.Fit Torx bolts to seat hinges and tighten to 25
Nm (18 lbf.ft).
3.Lower seat.
4.Fit Torx bolts to heel board and tighten to 25
Nm (18 lbf.ft).
Cushion & squab - rear seat - bench type
- 3 door
$% 78.10.57.99
Remove
1.Remove 2 Torx bolts securing seat to heel
board.
2.Fold seat forward and remove 2 Torx bolts from
hinges.
3.With assistance, remove seat.
Refit
1.With assistance, position seat and align hinges.
2.Fit Torx bolts, lower seat and tighten to 25 Nm
(18 lbf.ft).
3.Fit Torx bolts to heel board and tighten to 25
Nm (18 lbf.ft).
Page 708 of 1007
SEATS
REPAIRS 76-5-13
Cover - squab - rear seat - side - LH
$% 78.90.12
Remove
1.Fold LH rear seat forward.
2.Remove 5 screws and remove both end
covers.
3.Remove 3 bolts from seat squab and remove
squab from cushion.
4.Remove head restraint5.Release squab cover from sides and bottom of
frame.
6.Release latch escutcheon and remove seat
frame back cloth.
7.Release cover from rear of frame.
8.Remove both head restraint guide tubes.
9.Remove squab cover and pad from frame.
10.Remove and discard 9 hog rings and remove
cover from pad.
Refit
1.Position latch escutcheon to back cloth and fit
to frame. Ensure that the latch escutcheon is
secured correctly into latch housing.
2.Position squab cover to pad and secure hog
rings.
3.Fit squab cover and pad to frame.
4.Fit head restraint guide tubes.
5.Fit cover to sides and bottom of frame.
6.Fit cover to rear of frame.
7.Fit head restraint.
8.Fit cushion to squab and tighten Torx bolts to
28 Nm (21 lbf.ft).
9.Fit side covers and tighten screws.
10.Secure rear seat in locked position.
Page 709 of 1007
SEATS
76-5-14 REPAIRS
Cover - squab - rear seat - RH
$% 78.90.13
Remove
1.Fold RH rear seat forward.
2.Remove 2 screws and remove seat belt reel
cover.
3.Remove nut and release seat belt reel.4.Remove 5 screws and remove both end
covers.
5.Remove 3 bolts from seat squab and remove
squab from cushion.
6.Remove both head restraints.
7.Remove arm rest aperture trim.
8.Remove 2 screws from arm rest and remove
arm rest.