homelink Lexus CT200h 2016 OWNERS MANUAL QUICK GUIDE (in English)
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2016, Model line: CT200h, Model: Lexus CT200h 2016Pages: 90, PDF Size: 5.12 MB
Page 77 of 90
77
CT200h_QG_OM76210U_(U)
Portable Audio Device Ports
Press down and release the lid.
Open the cover and connect the portable
audio device.
Garage Door Opener (if equipped)
The garage door opener (HomeLink® Universal Transceiver) is manufactured under
license from HomeLink
®.
■Programming the HomeLink®
The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be pro-
grammed to operate 3 different devices. Refer to the programming method below appro-
priate for the device.
Garage door operation indicators
HomeLink
® indicator light
Buttons
These ports can be used to connect a portable audio device and listen to it through the
vehicle’s speakers.
The garage door opener can be programmed to operate garage doors, gates, entry
doors, door locks, home lighting systems, security systems, and other devices.
1
2
3
Page 78 of 90
78
CT200h_QG_OM76210U_(U)
■Programming HomeLink®
Point the remote control transmitter for
the device 1 to 3 in. (25 to 75 mm)
from the HomeLink
® buttons.
Keep the HomeLink
® indicator light in
view while programming.
For U.S.A. owners
Press and hold the HomeLink
® button
you want to program and the remote
control transmitter button simulta-
neously. When the HomeLink
® indica-
tor light changes from slowly flashing
orange to rapidly flashing green (roll-
ing code) or continuously lit green
(fixed code), release both buttons.
Programming an entry gate (for U.S.A. owners)/Programming a device in the
Canadian market
With one hand, press and hold the HomeLink
® button you want to program. With your
other hand, press and release the remote control transmitter every 2 seconds and
repeat this cycle until the HomeLink
® indicator light starts to flash rapidly. Then,
release the buttons.
Te s t t h e H o m e L i n k
® operation by pressing the newly programmed button and observ-
ing the indicator light:
●If the indicator light is solid/continuous, programming has been completed and your
device should activate when the HomeLink
® button is pressed and released.
●If the indicator light blinks rapidly for 2 seconds and then turns into a solid/continu-
ous light, proceed to the heading “Programming a Rolling Code System”.
Repeat the steps above to program another device for any of the remaining
HomeLink
® buttons.
1
2
2
3
4
Page 79 of 90
79
CT200h_QG_OM76210U_(U)
■Programming a Rolling Code System
Locate the “learn” or “smart” button on the garage door opener motor in the garage.
This button can usually be found where the hanging antenna wire is attached to the unit.
The name and color of the button may vary by manufacturer. Please refer to the
Owner’s manual supplied with the garage door opener motor for details.
Press and release the “learn” or “smart” button.
Perform step within 30 seconds after performing step .
Press and hold the programmed HomeLink
® button (located inside the vehicle) for 2
seconds and release it. Repeat this sequence (press/hold/release) up to 3 times to
complete programming.
If the garage door opener motor activates when the HomeLink
® button is pressed, the
garage door opener motor recognizes the HomeLink
® signal.
LEXUS Enform Safety Connect (if equipped)
■System components
Microphone
LED light indicators
“SOS” button
1
2
32
3
Safety Connect is a subscription-based telematics service that uses Global Positioning
System (GPS) data and embedded cellular technology to provide safety and security
features to subscribers. Safety Connect is supported by Lexus’ designated response
center, which operates 24 hours per day, 7 days per week.
Safety Connect service is available by subscription on select, telematics hardware-
equipped vehicles.
1
2
3