engine oil Lexus ES300 2000 s (in English) Owner's Guide

ENGINE
403
62E002a

1Add oil 2O.K. 3Too full
4. Pull the dipstick out and look at the oil level on the end.
If it is between the low level mark ( 4 ) and the full level
mark ( 5 ), it is O.K.

ENGINE
405
If the oil level is below or only slightly above the low
mark, add engine oil of the same type as already in
the engine.
Remove the oil filler cap and add engine oil a little at a
time,
checking the dipstick. The approximate quantity of
oil needed to fill between the low level mark and the full
level mark on the dipstick is indicated below for
reference.
When the level reaches within the correct range, return
the filler cap and turn the cap clockwise until you hear a
click.
Oil quantity. L (qt., lmp. qt.) 1.5 (1.6, 1.3)
NOTICE
Avoid overfilling, or the engine could be
damaged. Ch eck the oil level on the dipstick once
again after adding the oil.

ENGINE
406
Engine oil selection
Use API SJ, ªEnergy±Conservingº multigrade engine oil
or ILSAC multigrade engine oil.
Recommended viscosity (SAE):
62L005±1
Temperature range anticipated before next oil change
SAE 5W±30 is the best choice for your vehicle, for
good fuel economy, and good starting in cold
weather.
If you use SAE 10W±30 engine oil in extremely low
temperatures, the engine may become difficult to
start, so SAE 5W±30 engine oil is recommended.

ENGINE
407
Oil identification marks
62L006±1

API Service Symbol
ILSAC Certification
Mark
Either or both API registered marks are added to some
oil containers to help you select the oil you should use.
 The API Service Symbol is located anywhere on the
outside of the container.
The top portion of the label shows the oil quality by
API (American Petroleum Institute) designation such
as SJ. The center portion of the label shows the SAE
viscosity grade such as SAE 5W±30.
ªEnergy±Conservingº, shown in the lower portion,
indicates that the oil has fuel±saving capabilities.
 The ILSAC (International Lubricant Standardization
and Approval Committee) Certification Mark is
displayed on the front of the container.
CHECKING THE ENGINE
COOLANT LEVEL

GAS STATION INFORMATION

Fuel selection:
Select Octane Rating 87 (Research Octane Number
91) or higher. For improved vehicle performance, the
use of premium unleaded gasoline with an Octane
Rating 91 ( Research Octane Number 96) or higher is
recommended.

Fuel tank capacity:
70 L (18.5 gal., 15.4 lmp. gal.)

Engine oil:
API SJ, ªEnergy±Conservingº multigrade engine oil
or ILSAC multigrade engine oil.
Recommended oil viscosity ± SAE 5W±30 if normal
temperatures are below 38 C (100F)
Oil capacity: L (qt., lmp.qt.)
Drain and refill with filter 4.7 (5.0, 4.1)
without filter 4.5 (4.8, 4.0)
See page 402 for detailed information.

Engine coolant:
Capacity: 8.8 L (9.3 qt., 7.7 lmp. qt.)
Coolant type ± ªTOYOTA Long Life Coolantº or
equivalent
With ethylene±glycol type coolant for a proper
corrosion protection of aluminum components
Do not use alcohol type antifreeze or plain water alone.
For checking the engine coolant, see page 407
.

Automatic transaxle:
Fluid type ± Automatic transmission fluid Type T±IV

Tire information:
See page 423 through 432 for detailed information.

Tire pressure:
Tire size: P205/65R15 92V or P215/60R16 91V
cold tires
kPa (kgf/cm
2 or bar, psi)
Vehicle loaded
up Vehicle load up to vehicle
capacity to 4 occupants weight
Front tires 180 (1.8, 26) 220 (2.2, . . . . . . . . . . . .
32)
Rear tires 180 (1.8, 26) 220 (2.2, . . . . . . . . . . .
32)
When driving under the above vehicle load conditions at
sustained high speeds above 160 km/h (100 mph), in
countries where such speeds are permitted by law,
inflate the front and rear tires 220 kPa (2.2 kgf/cm
2 or bar,
32 psi), but never exceed the maximum cold tire
pressure molded on the tire sidewall.