tow LEXUS ES300 2005 User Guide

PRE±DELIVERY SERVICE (PDS) INFORMATION FOR ES 330 ± PD002-03 August 26, 2003
Page 3 of 9
REMOVAL OF FRONT EMERGENCY TOWING EYELET AND INSTALLATION OF
TOWING EYELET HOLE COVER (PERFORMED AT PORT)
1. Remove the emergency towing eyelet
from the front bumper by turning
counterclockwise.
NOTE:
If it is hard to loosen the emergency
towing eyelet, use a steel bar.
2. Place the removed emergency
towing eyelet in the tool tray in the
luggage compartment.
3. Install the front towing eyelet hole
cover which is stored in the glove box
onto the front bumper as shown in
the diagram. ITEM NO. 2:
Emergency Towing Eyelet
Installation
Procedure

PRE±DELIVERY SERVICE (PDS) INFORMATION FOR ES 330 ± PD002-03 August 26, 2003
Page 8 of 9
INITIAL CALIBRATION OF COMPASS (Continued)
3. Check that the direction appears
several seconds after adjustment.
4. Start the engine and push the switch
for about 6 seconds until ªCº appears
on the display.
5. Drive the vehicle slowly at 5 mph, or
less, in a circle until the direction is
displayed. If there is not enough space
to drive in a circle, drive around the
block until the direction is displayed.
After driving in circles 1 to 3 times,
calibration is complete with the direction
shown on the display.
NOTE:
Do not perform calibration of the compass in a place where the earth's magnetic
field is subject to interference by artificial magnetic fields (underground parking,
under a steel tower, between buildings, roof parking, near a railroad crossing, near
a large vehicle, etc.)
During calibration, do not operate electric systems (moon roof, power windows,
etc.) as they may interfere with the calibration.
ITEM NO. 5:
Compass
Calibration
Procedure
(Continued)

INITIAL CALIBRATION OF COMPASS DURING PDS ± PD034-05 August 22, 2005
Page 3 of 3
3. Check that the direction appears
several seconds after adjustment.
4. Start the engine and push the switch
for about 6 seconds until ªCº appears
on the display.
5. Drive the vehicle slowly at 5 mph
(8 km/h), or less, in a circle until the
direction is displayed. If there is not
enough space to drive in a circle,
drive around the block until the
direction is displayed.
After driving in 1 to 3 circles,
calibration is complete with the
direction shown on the display.
NOTE:
Do NOT perform calibration of the compass in a place where the Earth's magnetic
field is subject to interference by artificial magnetic fields (underground parking,
under a steel tower, between buildings, roof parking, near a railroad crossing, near
a large vehicle, etc.)
During calibration, do NOT operate electric systems (moon roof, power windows,
etc.) as they may interfere with the calibration. Compass
Calibration
Procedure
(Continued)

Lexus Supports ASE CertificationPage 1 of 2
Title:
FRONT EMERGENCY TOWING EYELET &
EYELET HOLE COVER
Models:
'05 ± '06 ES 330
Technical Service
Information Bulletin
August 26, 2005
PD037-05
The 2005 ± 2006 model year ES 330 is shipped with a front emergency towing eyelet.
Follow the procedure below to remove the eyelet and save for customer use.
2005 ± 2006 model year ES 330 vehicles.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
1. Remove the emergency towing
eyelet from the front bumper by
turning counterclockwise.
NOTE:
If it is hard to loosen the emergency
towing eyelet, use a steel bar.
PRE-DELIVERY SERVICE
Introduction
Applicable
Vehicles
Warranty
Information
Emergency Towing Eyelet
Installation
Procedure

FRONT EMERGENCY TOWING EYELET & EYELET HOLE COVER ± PD037-05 August 26, 2005
Page 2 of 2
2. Place the emergency towing
eyelet in the tool tray in the
luggage compartment.
3. Install the front towing eyelet hole
cover, which is stored in the glove
box, onto the front bumper as shown
in the illustration.Installation
Procedure
(Continued)