high beam Lexus ES300h 2016 Owner's Manual (OM33B71U)

3
ES300h_OM_OM33B71U_(U)
1
9 8
7
6 4 3
2
10
5
4-1. Before drivingDriving the vehicle ......................154
Cargo and luggage.................... 160
Vehicle load limits ........................163
Trailer towing .................................164
Dinghy towing ...............................165
4-2. Driving procedures Power (ignition) switch ..............166
EV drive mode ............................... 171
Hybrid transmission .................... 173
Turn signal lever ............................ 176
Parking brake ................................ 177
4-3. Operating the lights and wipers
Headlight switch .......................... 178
Automatic High Beam................ 181
Fog light switch ............................ 185
Windshield wipers and washer ................................. 186
4-4. Refueling Opening the fuel tank cap ...... 190 4-5. Using the driving support
systems
Lexus Safety System+ ................194
PCS (Pre-Collision System) .......... 201
LDA (Lane Departure Alert with steering co ntrol) ..............213
Dynamic radar cruise control............................ 222
Cruise control ............................. 234
Intuitive parking assist ...............237
Lexus parking assist monitor.........................................246
Driving mode select switch ............................................262
BSM (Blind Spot Monitor)..... 264 •Blind Spot Monitor function ..................................... 267
• Rear Cross Traffic Alert
function .................................... 269
Driving assist systems ............... 272
4-6. Driving tips Hybrid vehicle driving tips ......278
Winter driving tips ..................... 280
4Driving

20Pictorial index
ES300h_OM_OM33B71U_(U)
■Switches
Outside rear view mirror switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P. 142
Instrument panel light control swit ches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 87
Odometer/trip meter and trip meter reset button . . . . . . . . . . . . . . . . . . . P. 87
Automatic High Beam switch
*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 181
Intuitive parking assist switch
* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 237
BSM (Blind Spot Monitor) main switch
*. . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 264
Tire pressure warning reset switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 461
1
2
3
4
5
6
7

84
ES300h_OM_OM33B71U_(U)2. Instrument cluster
The indicators inform the driver of the operating state of the vehicle’s various sys-
tems.
Indicators
Turn signal indicator
(
 P. 1 76 )
(if equipped)
“LDA” (Lane Departure
Alert with steering control)
indicator ( P. 2 1 3 )
(U.S.A.)
Headlight indicator
( P. 1 7 8 )
(if equipped)
Intuitive parking assist
indicator ( P. 2 3 7 )
(Canada)
Tail light indicator
( P. 1 7 8 ) *1, 2Slip indicator light
( P. 2 7 3 )
Headlight high beam
indicator ( P. 1 7 9 )
*1VSC OFF indicator
( P. 2 74 )
(if equipped)
Automatic High Beam
indicator ( P. 1 8 1 ) *1, 3
(if equipped)
PCS warning light
( P. 2 0 4 )
Fog light indicator
(  P. 1 8 5 )
*4, 5
(if equipped)
BSM outside rear view
mirror indicators
( P. 2 6 4 )
“READY” indicator
( P. 166)*1, 6
“A I R B A G O N / O F F ”
indicator ( P. 4 6 )
EV indicator ( P. 6 9 )
Cruise control indicator
(  P. 230, 234)
(U.S.A.)
Parking brake indicator
( P. 1 7 7 )
(if equipped)
Radar cruise control
indicator ( P. 222)
(Canada)
Parking brake indicator
( P. 1 7 7 )
Cruise control “SET”
indicator ( P. 2 3 4 )*7Low outside temperature
indicator ( P. 9 1 )

153
ES300h_OM_OM33B71U_(U)
4Driving
4-1. Before drivingDriving the vehicle ...................... 154
Cargo and luggage .................... 160
Vehicle load limits ....................... 163
Trailer towing ................................. 164
Dinghy towing............................... 165
4-2. Driving procedures Power (ignition) switch.............. 166
EV drive mode ............................... 171
Hybrid transmission ....................173
Turn signal lever ............................ 176
Parking brake .................................177 4-3. Operating the lights
and wipers
Headlight switch...........................178
Automatic High Beam ................181
Fog light switch ............................ 185
Windshield wipers and washer.................................. 186
4-4. Refueling Opening the fuel tank cap ...... 190
4-5. Using the driving support systems
Lexus Safety System+ ............... 194
PCS (Pre-Collision System)........... 201
LDA (Lane Departure Alert with steering control) ............. 213
Dynamic radar cruise control ............................ 222
Cruise control ............................. 234
Intuitive parking assist .............. 237
Lexus parking assist monitor ........................................ 246
Driving mode select switch ........................................... 262
BSM (Blind Spot Monitor) ..... 264 • Blind Spot Monitor
function .....................................267
• Rear Cross Traffic Alert function .................................... 269
Driving assist systems................272
4-6. Driving tips Hybrid vehicle driving tips...... 278
Winter driving tips .....................280

ES300h_OM_OM33B71U_(U)
1794-3. Operating the lights and wipers
4
Driving
With the headlights on, push the
lever away from you to turn on the
high beams.
Pull the lever toward you to the center
position to turn the high beams off.
Pull the lever toward you and release
it to flash the high beams once.
You can flash the high beams with the
headlights on or off.
AFS (Adaptive Front-lighting System) improves visibility at intersections and on
curves by automatically adjusting the lateral angle of the headlights according to
vehicle speed and the degree of the tire angle that are controlled by steering
input.
Operates at speed of 6 mph (10 km/h) or higher.
■Deactivating AFS
Select “AFS” on the (settings display) of the multi-information dis-
play. ( P. 9 2 )
Press the meter control switch.
■Daytime running light system
●To make your vehicle more visible to other drivers during daytime driving, the daytime
running lights turn on automatically whenever the hybrid system is started and the park-
ing brake is released. (Illum inate brighter than the parking lights.) Daytime running
lights are not designed for use at night.
For the U.S.A.: Daytime running lights can be turned off by operating the switch.
●Compared to turning on the headlights, the daytime running light system offers greater
durability and consumes less electricity, so it can help improve fuel economy.
■Headlight control sensor
Turning on the high beam headlights
1
2
AFS (Adaptive Front-lighting System) (if equipped)
The sensor may not function properly if an
object is placed on the sensor, or anything that
blocks the sensor is affixed to the windshield.
Doing so interferes with the sensor detecting
the level of ambient light and may cause the
automatic headlight system to malfunction.
1
2

181
ES300h_OM_OM33B71U_(U)4-3. Operating the lights and wipers
4
Driving
Automatic High Beam
Push the lever away from you with
the headlight switch in the or
position.
Press the Automatic High Beam
switch.
The Automatic High Beam indicator will
come on when the headlights are turned
on automatically to indicate that the sys-
tem is active.
: If equipped
The Automatic High Beam uses an in-v ehicle camera sensor to assess the
brightness of streetlights, the lights of vehicles ahead, etc., and automatically
turns the high beam on or off as necessary.
WA R N I N G
■Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to observe
your surroundings and turning the high beam on or off manually if necessary.
■To prevent incorrect operation of the Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic High Beam system
1
2

182
ES300h_OM_OM33B71U_(U)4-3. Operating the lights and wipers
■Switching to low beam
Pull the lever to the original position.
The Automatic High Beam indicator
will turn off.
Push the lever away from you to acti-
vate the Automatic High Beam sys-
tem again.
■Switching to high beam
Press the Automatic High Beam
switch.
The Automatic High Beam indicator
will turn off and the high beam indi-
cator will turn on.
Press the switch to activate the Auto-
matic High Beam system again.
■High beam automatic turning on or off conditions
●When all of the following conditions are fu
lfilled, the high beam will be automatically
turned on:
• Vehicle speed is above appr oximately 21 mph (34 km/h).
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with headlights or tail lights turned on.
• There are few streetlights on the road ahead.
●If any of the following conditions are fulfilled, the high beam will be automatically turned
off:
• Vehicle speed drop s below approximately 17 mph (27 km/h).
• The area ahead of the vehicle is not dark.
• Vehicles ahead have headlights or tail lights turned on.
• There are many streetlights on the road ahead.
Turning the high beam on/off manually

ES300h_OM_OM33B71U_(U)
1834-3. Operating the lights and wipers
4
Driving
■Camera sensor detection information
●The high beam may not be automatically turned off in the following situations:
• When oncoming vehicles sudd enly appear from a curve
• When the vehicle is cut in front of by another vehicle
• When vehicles ahead are hidden from sight due to repeated curves, road dividers or roadside trees
• When vehicles ahead appear from the faraway lane on wide road
• When vehicles ahead have no lights
●The high beam may be turned off if a vehicl e ahead that is using fog lights without using
the headlights is detected.
●House lights, street lights, traffic signals, and illuminated billboards or signs may cause
the high beam to switch to the low be ams, or the low beams to remain on.
●The following factors may affect the amount of time taken to turn the high beam on or
off:
• The brightness of headlights, fog lights, and tail lights of vehicles ahead
• The movement and direction of vehicles ahead
• When a vehicle ahead only has operational lights on one side
• When a vehicle ahead is a two-wheeled vehicle
• The condition of the road (gradient, curve, condition of the road surface etc.)
• The number of passengers and amount of luggage
●The high beam may be turned on or off when the driver does not expect it.
●Bicycles or similar objects may not be detected.
●In the situations shown below, the system may not be able to accurately detect sur-
rounding brightness levels. This may caus e the low beams to remain on or the high
beams to cause problems for pedestrians, ve hicles ahead or other parties. In these
cases, manually switch between the high and low beams.
• In bad weather (rain, snow, fog, sandstorms etc.)
• The windshield is obscured by fog, mist, ice, dirt etc.
• The windshield is cracked or damaged.
• The camera sensor is deformed or dirty.
• The camera sensor temperature is extremely high.
• Surrounding brightness levels are equal to those of headlights, tail lights or fog lights.
• Vehicles ahead have headlights or tail lights that are either switched off, dirty, are
changing color, or are not aimed properly.
• When driving through an area of intermit tently changing brightness and darkness.
• When frequently and repeatedly driving ascending/descending roads, or roads with rough, bumpy or uneven surfaces (such as stone-paved roads, gravel tracks etc.).
• When frequently and repeat edly taking curves or driving on a winding road.
• There is a highly reflective object ahead of the vehicle, such as a sign or a mirror.
• The back of a vehicle ahead is highly reflective, such as a container on a truck.
• The vehicle’s headlights are damaged or dirty, or are not aimed properly.
• The vehicle is listing or tilting due to a flat tire, a trailer being towed, etc.
• The high beam and low beam are repeatedly being switched between in an abnor- mal manner.
• The driver believes that the high beam may be causing problems or distress to other
drivers or pedestrians nearby.

184
ES300h_OM_OM33B71U_(U)4-3. Operating the lights and wipers
■Temporarily lowering sensor sensitivity
The sensitivity of the sensor can be temporarily lowered.
Turn the power switch off while the following conditions are met.
• The headlight switch is in or .
• The headlight switch lever is in high beam position.
• Automatic High Beam switch is on. Turn the power switch to ON mode.
Within 30 seconds after , repeat pulling the headlight switch lever to the original
position then pushing it to the high beam position quickly 10 times, then leave the
lever in high beam position.
If the sensitivity is changed, the Automatic High Beam indicator is turn on and off
three times.
Automatic High Beam (headlights) may turn on even the vehicle is stopped.
1
2
32
4

194
ES300h_OM_OM33B71U_(U)4-5. Using the driving support systems
Lexus Safety System+
◆PCS (Pre-Collision System)

P. 2 0 1
◆LDA (Lane Departure Alert with steering control)
P. 2 1 3
◆Dynamic radar cruise control
P. 222
◆AHB (Automatic High Beam)
P. 1 8 1
: If equipped
The Lexus Safety System+ consists of the following drive assist systems and
contributes to a safe and comfo rtable driving experience:
WA R N I N G
■Lexus Safety System+
The Lexus Safety System+ is designed to operate under the assumption that the driver
will drive safely, and is designed to help reduce the impact to the occupants and the
vehicle in the case of a collision or assist the driver in normal driving conditions.
As there is a limit to the degree of recognition accuracy and control performance that
this system can provide, do not overly rely on this system. The driver is always responsi-
ble for paying attention to the vehicl e’s surroundings and driving safely.