ECU Lexus GS300h 2013 Manual Online

811 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS450h_300h_OM_OM30D53E_(EE)
Rear turn signal lights
Open the trunk lid and
remove the cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
When installing, reverse the
steps listed.
After installing the bulb base,
secure the cord with the clips
and install the cover in its origi-
nal position.
1
2
3
4

815 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS450h_300h_OM_OM30D53E_(EE)
Remove the screws and take
off the mirror cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
After installing the new
bulb, secure the socket to
the light body.
When inserting the socket, align
the marks printed on the light
body and the socket.
4
5
6
7

8166-3. Do-it-yourself maintenance
GS450h_300h_OM_OM30D53E_(EE)
Install the visor cover on the
mirror frame, secure it with
a screw, and install the side
turn signal light and outer
foot light.
Use only the screw position
shown in the illustration.
Side turn signal light: Align the
tabs on the light and the cover
and install.
Outer foot light: Interlock the
tabs in the groove of the light
body with those on the cover,
and secure.
Disconnect the tabs, and
separate the top and bottom
of the rear side cover of the
mirror.
8
9

817 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS450h_300h_OM_OM30D53E_(EE)
Install the cover of the back
end of the mirror, installing
the lower side and the upper
side in that order.
When installing the lower side
of the cover, insert the side turn
signal light pin into the hole in
the cover.
Secure the cover with
screws and reconnect the
connectors back together.
Secure the cords by returning
them to the hooks as they were.
Align the tabs, and secure
the mirror by pushing in
each diagonally-opposite
pair of tabs in order.
Make sure to insert the tabs in
order as shown in the illustra-
tion, and push them in until a
click is heard.
If you do not hear the click, do
not force the tabs in. Instead,
remove the mirror and check
that the tabs are aligned.
10
11
12

819 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS450h_300h_OM_OM30D53E_(EE)P. 8 0 2
CAUTION
Replacing light bulbs
Turn off the lights. Do not attempt to replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may cause burns.
Do not touch the glass portion of the light bulb with bare hands. When it is
unavoidable to hold the glass portion, use and hold with a clean dry cloth
to avoid getting moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
Vehicles with discharge headlights:
While the headlights are turned on, and
for a short time after they have been
turned off, metal components at the rear
of the headlight assembly will be
extremely hot. To prevent burns, do not
touch these metal components until you
are certain they have cooled down.
Metal components

821
7 7-1. Essential information
When trouble arises
GS450h_300h_OM_OM30D53E_(EE)
If your vehicle has to be stopped in an emergency
Steadily step on the brake pedal with both feet and firmly depress
it.
Do not pump the brake pedal repeatedly as this will increase the effort
required to slow the vehicle.
Shift the shift lever to N.
If the shift lever is shifted to N
After slowing down, stop the vehicle in a safe place by the road.
Stop the hybrid system.
If the shift lever cannot be shifted to N
Keep depressing the brake pedal with both feet to reduce vehicle
speed as much as possible.
To stop the hybrid system,
press and hold the power
switch for 2 consecutive sec-
onds or more, or press it
briefly 3 times or more in suc-
cession.
Stop the vehicle in a safe place by the road.
Only in an emergency, such as if it becomes impossible to stop the
vehicle in the normal way, stop the vehicle using the following
procedure:
1
2
3
4
3
Press and hold for 2 seconds or
more or press briefly 3 times or
4
5

8237-2. Steps to take in an emergency
7
When trouble arises
GS450h_300h_OM_OM30D53E_(EE)
If a tow truck is not available in
an emergency, your vehicle may
be temporarily towed using a
cable or chain secured to the
emergency towing eyelet. This
should only be attempted on hard
surfaced roads for short distances
at under 30 km/h (18 mph).
A driver must be in the vehicle to
steer and operate the brakes. The
vehicle’s wheels, drive train,
axles, steering and brakes must
be in good condition.
Emergency towing

8247-2. Steps to take in an emergency
GS450h_300h_OM_OM30D53E_(EE)
Take out the towing eyelet. (P. 872, 886)
Remove the eyelet cover using
a flathead screwdriver.
To protect the bodywork, place a
rag between the screwdriver and
the vehicle body as shown in the
illustration.
Insert the towing eyelet into
the hole and tighten partially
by hand.
Tighten down the towing eye-
let securely using a wheel nut
wrench.
Installing towing eyelet
1
2
3
4

8277-2. Steps to take in an emergency
7
When trouble arises
GS450h_300h_OM_OM30D53E_(EE)
Before emergency towing
Release the parking brake.
Shift the shift lever to N.
Turn the power switch to ACCESSORY (hybrid system off) or ON (hybrid
system operating) mode.
CAUTION
Observe the following precautions.
Failure to do so may result in death or serious injury.
When transporting the vehicle
Caution while towing
Use extreme caution when towing the vehicle.
Avoid sudden starts or erratic driving maneuvers which place excessive
stress on the emergency towing eyelets and the cables or chains. Always
be cautious of the surroundings and other vehicles while towing.
If the hybrid system is off, the power assist for the brakes and steering will
not function, making steering and braking more difficult.
Installing towing eyelets to the vehicle
Make sure that towing eyelets are installed securely.
If not securely installed, towing eyelets may come loose during towing.
1
2
3
Be sure to transport the vehicle with the
rear wheels raised or with all four wheels
raised off the ground. If the vehicle is
towed with the rear wheels contacting
the ground, the drivetrain and related
parts may be damaged or the motor may
generate electricity. If the motor gener-
ates electricity, depending on the state of
the damage or malfunction, a fire may
dt hti it

8677-2. Steps to take in an emergency
7
When trouble arises
GS450h_300h_OM_OM30D53E_(EE)
Inte-
rior
buzzerExterior
buzzerWarning messageDetailsCorrection
procedure
Once
• When the doors
were unlocked
with the
mechanical key
and then the
power switch
was pressed, the
electronic key
could not be
detected in the
vehicle.
• The electronic
key could not
be detected in
the vehicle even
after the power
switch was
pressed two
consecutive
times.
To u c h t h e
electronic
key to the
power
switch
while
depressing
the brake
pedal.
Once
An attempt was
made to start the
hybrid system
with the shift
lever in an incor-
rect position.Shift the
shift lever
to P and
start the
hybrid sys-
tem.
(Flashes)
(Flashes)