light LEXUS GS400 2000 Service Repair Manual

I04102
ON OFF
I04103
ON OFF
I04104
Wire Harness Side
I01286
BatteryWarning Light
± BODY ELECTRICALCOMBINATION METER
BE±101
2402 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
26. INSPECT ENGINE OIL LEVEL WARNING SENSOR
(a) Check that continuity exists between terminals with the
switch to below 40 °C (104 °F). (Warning switch ON)
(b) Heat the switch to above 60 °C (140 °F) in an oil bath.
(c) Check that there is continuity between terminals with the
switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
27. INSPECT ENGINE OIL LEVEL WARNING SENSOR
CIRCUIT
Disconnect the switch connector and inspect the connector on
wire harness side, as shown.
Tester connectionConditionSpecified condition
2 ± GroundConstantContinuity
If continuity is not as specified, inspect the wire harness or
ground point.
28. INSPECT OPEN DOOR WARNING LIGHT
Disconnect the connector from the door courtesy switch and
ground terminal 1 on the wire harness side, and check that the
warning light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
29. INSPECT DOOR COURTESY SWITCH CONTINUITY
AND CIRCUIT (See page BE±60)

I04105
Dark
(10k W)Bright
(0W)
4
5
I01322
Battery Ignition
SwitchWarning Light
2 1 Wire Harness Side
I01323
1 2 OFF
ON
I01328
Battery Ignition
SwitchWarning Light
2 1 Wire Harness Side
I04107
12
4
OFF
ON BE±102
± BODY ELECTRICALCOMBINATION METER
2403 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
30. INSPECT LIGHT CONTROL RHEOSTAT OPERATION
Gradually, turn the rheostat knob from the bright side to dark
side and check that the resistance decreases from 10 kW to 0
W between terminal 4 and 5. (Rheostat knob turned to clock-
wise)
If operation is not as specified, replace the rheostat light control.
31. INSPECT WINDOW WASHER LEVEL WARNING
LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Engine running and check that the warning light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
32. INSPECT WINDOW WASHER LEVEL WARNING
SWITCH CONTINUITY
(a) Check that no continuity exists between the terminals with
the switch OFF (float up).
(b) Check that continuity exists between the terminals with
the switch ON (float down).
If operation is not as specified, replace the switch or inspect
ground point.
33. INSPECT SEAT BELT WARNING LIGHT
(a) Disconnect the connector from the retractor switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
34. INSPECT SEAT BELT BUCKLE SWITCH CONTINUITY
(a) Check that continuity exists between the terminals 1 and
4 on the switch side connector with the switch ON (belt
fastened).
(b) Check that continuity exists between the terminals 2 and
4 on the switch side connector with the switch OFF (belt
unfastened).
If operation is not as specified, replace the switch.

± BRAKETROUBLESHOOTING
BR±3
2111 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) Noise from brakes
1. Pad (Cracked or distorted)
2. Installation bolt (Loose)
3. Disc (Scored)
4. Pad support plate (Loose)
5. Sliding pin (Worn)
6. Pad (Dirty)
7. Pad (Glazed)
8. Tension or return spring (Faulty)
9. Anti±squeal shim (Damaged)
10.Shoe hold±down spring (Damaged)BR±15
BR±24
BR±15
BR±24
BR±18
BR±27
BR±18
BR±18
BR±15
BR±24
BR±15
BR±24
BR±33
BR±18
BR±27
BR±33
Noise from hydraulic brake booster
(Abnormal pump motor operation noise)Accumulator bracket clearance (Out or adjustment)BR±56
Brake warning light lights up*1
(Parking brake pedal released)
1. Brake fluid level
2. Hydraulic brake booster power supply system (Faulty)BR±38
Brake warning light lights up and brake warning buzzer sounds*2Hydraulic brake booster power supply system (Faulty)BR±38
ABS warning light lights up*31. Anti±lock brake system (Faulty)
2. Hydraulic brake booster power supply system (Faulty)
BR±38
*1, *3: The light may stay on for about 60 seconds after the engine has been started. It is normal if it goes
out after a while.
*
2, *3: Depressing the brake pedal repeatedly may turn on the warning light and buzzer. It is normal if the
light goes out and the buzzer stops sounding after a few seconds.
*
3: While ABS warning light is ON, both VSC warning light and VSC OFF indicator light come on.

F02847
Stop Light Switch
Push Rod
Pedal HeightBR0JB±07
F02849
Pedal Freeplay
± BRAKEBRAKE PEDAL
BR±9
2117 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
BRAKE PEDAL
ON±VEHICLE INSPECTION
1. CHECK PEDAL HEIGHT
Pedal height from asphalt sheet:
150.0 ± 160.0 mm (5.906 ± 6.299 in.)
2. IF NECESSARY, ADJUST PEDAL HEIGHT
(a) Remove the No. 1 under cover, end pad, No. 1 safety pad
and No. 7 heater to register duct (See page BO±88).
(b) Disconnect the connector from the stop light switch.
(c) Loosen the stop light switch lock nut and remove the stop
light switch.
(d) Loosen the push rod lock nut.
(e) Adjust the pedal height by turning the pedal push rod.
(f) Tighten the push rod lock nut.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(g) Install the stop light switch.
(h) Push in the brake pedal 5 ± 15 mm (0.20 ± 0.59 in.), turn
the stop light switch to lock the nut in the position where
the stop light goes off.
(i) Connect the connector to the stop light switch.
(j) After installation, push in the brake pedal 5 ± 15 mm (0.20
± 0.59 in.), check that stop light lights up.
(k) After adjusting the pedal height, check the pedal freeplay.
(l) Install the No. 7 heater to register duct, No. 1 safety pad,
end pad and No. 1 under cover.
3. CHECK PEDAL FREEPLAY
(a) Stop the engine and depress the brake pedal more than
40 times until there is no more pressure left in the booster.
(b) Push in the pedal by hand until the second point of resis-
tance begins to be felt, then measure the distance, as
shown.
Pedal freeplay: 0.2 ± 2.0 mm (0.008 ± 0.079 in.)
If incorrect, check the stop light switch clearance. If the clear-
ance is OK, then troubleshoot the brake system.
Stop light switch clearance:
0.5 ± 2.4 mm (0.020 ± 0.094 in.)
HINT:
The freeplay to the 1st point of resistance is due to the play be-
tween the clevis and pin. It is 0.2 ± 2.0 mm (0.008 ± 0.079 in.)
on the pedal.

CH043±01
B01372
Except Maintenance±Free Battery
B01888
Maintenance±Free BatteryVoltmeter
± CHARGING (2JZ±GE)CHARGING SYSTEM
CH±1
1603 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
CHARGING SYSTEM
ON±VEHICLE INSPECTION
CAUTION:

Check that the battery cables are connected to the
correct terminals.

Disconnect the battery cables when the battery is giv-
en a quick charge.

Do not do tests with a high voltage insulation resis-
tance tester.

Never disconnect the battery while the engine is run-
ning.
1. CHECK BATTERY ELECTROLYTE LEVEL
Check the electrolyte quantity of each cell.
Maintenance±Free Battery:
If under the lower level, replace the battery (or add distilled wa-
ter if possible). Check the charging system.
Except Maintenance±Free Battery:
If under the lower level, add distilled water.
2. Except Maintenance±Free Battery:
CHECK BATTERY SPECIFIC GRAVITY
Check the specific gravity of each cell.
Standard specific gravity: 1.25 ± 1.29 at 20°C (68°F)
If the specific gravity is less than specification, charge the bat-
tery.
3. Maintenance±Free Battery:
CHECK BATTERY POSITIVE VOLTAGE
(a) After having driven the vehicle and in the case that 20
minutes have not passed after having stopped the en-
gine, turn the ignition switch ON and turn on the electrical
system (headlight, blower motor, rear defogger etc.) for
60 seconds to remove the surface charge.
(b) Turn the ignition switch OFF and turn off the electrical sys-
tems.
(c) Measure the battery positive voltage between the nega-
tive (±) and positive (+) terminals of the battery.
Standard voltage: 12.5 ± 12.9 V at 20°C (68°F)
If the voltage is less than specification, charge the battery.
4. CHECK BATTERY TERMINALS AND FUSES
(a) Check that the battery terminals are not loose or cor-
roded.
If the terminals are corroded, clean the terminals.
(b) Check the fusible link and fuses for continuity.

Z03473
Ammeter
Battery
VoltmeterGenerator Disconnect Wire
from Terminal B
B01656
Terminal F
± CHARGING (2JZ±GE)CHARGING SYSTEM
CH±3
1605 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
7. CHECK CHARGE WARNING LIGHT CIRCUIT
(a) Warm up the engine and then turn it off.
(b) Turn off all accessories.
(c) Turn the ignition switch ºONº. Check that the charge warn-
ing light is lit.
(d) Start the engine. Check that the light goes off.
If the light does not go off as specified, troubleshoot the charge
light circuit.
8. INSPECT CHARGING CIRCUIT WITHOUT LOAD
HINT:
If a battery/generator tester is available, connect the tester to
the charging circuit as per manufacturer's instructions.
(a) If a tester is not available, connect a voltmeter and amme-
ter to the charging circuit as follows:

Disconnect the wire from terminal B of the genera-
tor, and connect it to the negative (±) probe of the
ammeter.

Connect the positive (+) probe of the ammeter to
terminal B of the generator.

Connect the positive (+) probe of the voltmeter to
terminal B of the generator.

Ground the negative (±) probe of the voltmeter.
(b) Check the charging circuit as follows:
With the engine running from idling to 2,000 rpm, check
the reading on the ammeter and voltmeter.
Standard amperage: 10 A or less
Standard voltage: 13.2 ± 14.8 V
If the voltmeter reading is more than standard voltage, replace
the voltage regulator.
If the voltmeter reading is less than standard voltage, check the
voltage regulator and generator as follows:

With terminal F grounded, start the engine and
check the voltmeter reading of terminal B.

If the voltmeter reading is more than standard volt-
age, replace the voltage regulator.

If the voltmeter reading is less than standard volt-
age, check the generator.
9. INSPECT CHARGING CIRCUIT WITH LOAD
(a) With the engine running at 2,000 rpm, turn on the high
beam headlights and place the heater blower switch at
ºHIº.
(b) Check the reading on the ammeter.
Standard amperage: 30 A or more
If the ammeter reading is less than the standard amperage, re-
pair the generator.
HINT:
If the battery is fully charged, the indication will sometimes be
less than standard amperage.

CO0AA±01
CO1205
Dimension B
Stopper Bolt
Overhaul HandlePart A
ClawSST
B01865
Lock
PlateSST
Stopper BoltTank
B01867
Ta p
B02033
± COOLING (2JZ±GE)RADIATOR
CO±19
1557 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
DISASSEMBLY
1. REMOVE PACKINGS
2. REMOVE RADIATOR CAP
3. REMOVE DRAIN PLUG
(a) Remove the drain plug.
(b) Remove the O±ring.
4. REMOVE ECT SWITCH
(a) Remove the ECT switch.
(b) Remove the O±ring.
5. ASSEMBLE SST
SST 09230±01010
(a) Install the claw to the overhaul handle, inserting it in the
hole in part A as shown in the diagram.
(b) While gripping the handle, adjust the stopper bolt so that
dimension B is as shown in the illustration.
Dimension B: 0.2 ± 0.3 mm (0.008 ± 0.012 in.)
NOTICE:
If this adjustment is not done the claw may be damaged.
6. UNCAULK LOCK PLATES
Using SST to release the caulking, squeeze the handle until
stopped by the stopper bolt.
SST 09230±01010
7. REMOVE TANKS AND O±RINGS
Lightly tap the bracket of the radiator (or radiator inlet or outlet)
with a soft±faced hammer, and remove the tank and the O±ring.
8. REMOVE OIL COOLER FROM LOWER TANK
(a) Loosen the nut, and remove the cooler pipe. Remove the
2 cooler pipes.
(b) Remove the 2 nuts and 2 plate washers.
(c) Remove the oil cooler and 2 O±rings.

CO0AB±03
B01862
75°
Pipe
CO0317O±Ring Normal X TwistedX Twisted
B01868
CORRECT
WRONG
Ta pTank
Plate
Lock
CO1206
Dimension B
Punch Assembly
Overhaul HandleStopper BoltPartSST
CO±20
± COOLING (2JZ±GE)RADIATOR
1558 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REASSEMBLY
1. INSTALL OIL COOLER TO LOWER TANK
(a) Install 2 new O±rings to the oil cooler.
(b) Install the oil cooler to the lower tank with the 2 plate
washers and 2 nuts.
Torque: 8.3 N´m (85 kgf´cm, 74 in.´lbf)
(c) Install the cooler pipes in the direction indicated in the il-
lustration.
Torque: 14.7 N´m (150 kgf´cm, 11 ft´lbf)
2. INSPECT LOCK PLATE FOR DAMAGE
HINT:

If the sides of the lock plate groove are deformed, reas-
sembly of the tank will be impossible.

Therefore, first correct any deformation with pliers or simi-
lar object. Water leakage will result if the bottom of the
lock plate groove is damaged or dented.
NOTICE:
The radiator can only be recaulked 2 times. After the 2nd
time, the radiator core must be replaced.
3. INSTALL NEW O±RINGS AND TANKS
(a) After checking that there are no foreign objects in the lock
plate groove, install a new O±ring without twisting it.
HINT:
When cleaning the lock plate groove, lightly rub it with sand pa-
per without scratching it.
(b) Install the tank without damaging the O±ring.
(c) Tap the lock plate with a soft±faced hammer so that there
is no gap between it and the tank.
4. ASSEMBLE SST
SST 09230±01010, 09231±14010
(a) Install the punch assembly to the overhaul handle, insert-
ing it in the hole in part A as shown in the illustration.
(b) While gripping the handle, adjust the stopper bolt so that
dimension B is as shown in the illustration.
Dimension B: 8.4 mm (0.331 in.)

B01863B01866B02081
8 7
6 5
43
2
1
Stopper
Bolt
SSTTank
Lock
Plate
B01861(1) (2)(3) (1)
(1)(1)(1) (3)
(3)
(3) (3)
B01864B01870B02082
B01869
H
± COOLING (2JZ±GE)RADIATOR
CO±21
1559 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
5. CAULK LOCK PLATE
(a) Lightly press SST against the lock plate in the order
shown in the illustration. After repeating this a few times,
fully caulk the lock plate by squeezing the handle until
stopped by the stopper plate.
SST 09230±01010
HINT:

Do not stake the areas protruding around the ports (1),
flange (2) and bracket (3).

The points shown in the illustration cannot be staked with
the SST. Use pliers or similar object and be careful not to
damage the core plates.
(b) Check the lock plate height (H) after completing the caulk-
ing.
Plate height (H): 7.40 ± 7.80 mm (0.2913 ± 0.3071 in.)
If not within the specified height, adjust the stopper bolt of the
handle again and caulk again.
6. INSTALL ECT SWITCH
(a) Install a new O±ring to the ECT switch.
(b) Install the ECT switch.
7. INSTALL DRAIN PLUG
(a) Install a new O±ring to the drain plug.

B01982
LEXUS
Hand±Held
Tester
EM0D3±02
A02667
TC
E1 SST
DLC1
A02668
Igniter
White Lead Wire
A02637
EM±12
± ENGINE MECHANICAL (2JZ±GE)IGNITION TIMING
1366 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
IGNITION TIMING
INSPECTION
1. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
2. CONNECT LEXUS HAND±HELD TESTER OR OBDII
SCAN TOOL
(a) Connect the LEXUS hand±held tester or OBDII scan tool
to the DLC3.
(b) Please refer to the LEXUS hand±held tester or OBDII
scan tool operator's manual for further details.
3. CONNECT TIMING LIGHT TO ENGINE
4. CHECK IDLE SPEED (See page EM±13)
5. INSPECT IGNITION TIMING
(a) Using SST, connect terminals TC and E1 of the DLC1.
SST 09843±18020
(b) Connect the timing light clip to the white lead wire.
NOTICE:
Use a timing light that can detect the primary signal.
(c) Using a timing light, check the ignition timing.
Ignition timing: 10 ± 2° BTDC @ idle
(Transmission in neutral position)
(d) Remove the SST from the DLC1.
6. FURTHER CHECK IGNITION TIMING
Ignition timing: 6 ± 16° BTDC @ idle
(Transmission in neutral position)
HINT:
The timing mark moves in a range between 6° and 16°.
7. DISCONNECT TIMING LIGHT FROM ENGINE
8. DISCONNECT LEXUS HAND±HELD TESTER OR
OBDII SCAN TOOL