drain bolt LEXUS GS400 2000 Service User Guide

BR0JS±06
F01639
BR±28
± BRAKEREAR BRAKE CALIPER
2136 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. DISCONNECT FLEXIBLE HOSE
Remove the union bolt and gasket from the caliper, then discon-
nect the flexible hose from the caliper. Use a container to catch
brake fluid as it drains out.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Install the flexible hose lock securely in the lock hole in the cali-
per.
3. REMOVE CALIPER
(a) Remove the 2 installation bolts.
Torque: 104 N´m (1,065 kgf´cm, 77 ft´lbf)
(b) Remove the caliper.
4. REMOVE BRAKE PADS (See page BR±25)
(a) Remove the anti±squeal spring.
(b) Remove the clip and pad guide pin.
(c) Remove the 2 pads with the 4 anti±squeal shims.

CO0A9±03
B01881
CO±18
± COOLING (2JZ±GE)RADIATOR
1556 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE ENGINE UNDER COVER
2. DRAIN ENGINE COOLANT
3. REMOVE AIR CLEANER INLET
4. REMOVE AIR CLEANER AND MAF METER AS-
SEMBLY
5. REMOVE RADIATOR AND ELECTRIC COOLING FAN
ASSEMBLY
(a) Disconnect the upper radiator hose from the radiator.
(b) Disconnect the lower radiator hose from the radiator.
(c) Disconnect the ECM outlet duct from the ECM box.
(d) Disconnect the wire for electric cooling fan from the clamp
on the electric cooling fan.
(e) Disconnect the 2 electric cooling fan connectors.
(f) Disconnect the ECT switch connector for electric cooling
fan.
(g) Disconnect the 2 oil cooler hoses for A/T from the radiator.
(h) Remove the 2 nuts and 2 upper radiator supports.
(i) Lift out the radiator and cooling fan assembly.
(j) Remove the 2 lower radiator supports.
6. REMOVE ELECTRIC COOLING FAN FROM RADIA-
TOR
(a) Disconnect the radiator reservoir hose from the radiator.
(b) Remove the 6 bolts and electric cooling fan.

CO0AA±01
CO1205
Dimension B
Stopper Bolt
Overhaul HandlePart A
ClawSST
B01865
Lock
PlateSST
Stopper BoltTank
B01867
Ta p
B02033
± COOLING (2JZ±GE)RADIATOR
CO±19
1557 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
DISASSEMBLY
1. REMOVE PACKINGS
2. REMOVE RADIATOR CAP
3. REMOVE DRAIN PLUG
(a) Remove the drain plug.
(b) Remove the O±ring.
4. REMOVE ECT SWITCH
(a) Remove the ECT switch.
(b) Remove the O±ring.
5. ASSEMBLE SST
SST 09230±01010
(a) Install the claw to the overhaul handle, inserting it in the
hole in part A as shown in the diagram.
(b) While gripping the handle, adjust the stopper bolt so that
dimension B is as shown in the illustration.
Dimension B: 0.2 ± 0.3 mm (0.008 ± 0.012 in.)
NOTICE:
If this adjustment is not done the claw may be damaged.
6. UNCAULK LOCK PLATES
Using SST to release the caulking, squeeze the handle until
stopped by the stopper bolt.
SST 09230±01010
7. REMOVE TANKS AND O±RINGS
Lightly tap the bracket of the radiator (or radiator inlet or outlet)
with a soft±faced hammer, and remove the tank and the O±ring.
8. REMOVE OIL COOLER FROM LOWER TANK
(a) Loosen the nut, and remove the cooler pipe. Remove the
2 cooler pipes.
(b) Remove the 2 nuts and 2 plate washers.
(c) Remove the oil cooler and 2 O±rings.

B01863B01866B02081
8 7
6 5
43
2
1
Stopper
Bolt
SSTTank
Lock
Plate
B01861(1) (2)(3) (1)
(1)(1)(1) (3)
(3)
(3) (3)
B01864B01870B02082
B01869
H
± COOLING (2JZ±GE)RADIATOR
CO±21
1559 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
5. CAULK LOCK PLATE
(a) Lightly press SST against the lock plate in the order
shown in the illustration. After repeating this a few times,
fully caulk the lock plate by squeezing the handle until
stopped by the stopper plate.
SST 09230±01010
HINT:

Do not stake the areas protruding around the ports (1),
flange (2) and bracket (3).

The points shown in the illustration cannot be staked with
the SST. Use pliers or similar object and be careful not to
damage the core plates.
(b) Check the lock plate height (H) after completing the caulk-
ing.
Plate height (H): 7.40 ± 7.80 mm (0.2913 ± 0.3071 in.)
If not within the specified height, adjust the stopper bolt of the
handle again and caulk again.
6. INSTALL ECT SWITCH
(a) Install a new O±ring to the ECT switch.
(b) Install the ECT switch.
7. INSTALL DRAIN PLUG
(a) Install a new O±ring to the drain plug.

CO0AF±03
B02071
± COOLING (2JZ±GE)ELECTRIC COOLING FAN
CO±27
1565 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE AIR CLEANER INLET
3. REMOVE AIR CLEANER AND MAF METER AS-
SEMBLY
4. REMOVE ELECTRIC COOLING FAN
(a) Disconnect the upper radiator hose from the radiator.
(b) Disconnect the ECM outlet duct from the ECM box.
(c) Disconnect the wire for electric cooling fan from the clamp
on the electric cooling fan.
(d) Disconnect the 2 electric cooling fan connector.
(e) Disconnect the radiator reservoir hose from the radiator.
(f) Remove the 6 bolts and electric cooling fan.

B01941
Drain Hose
CO±6
± COOLING (2JZ±GE)WATER PUMP
1544 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(e) Remove the 6 bolts, water pump and gasket.
(f) Remove the drain hose.
(g) Remove the O±ring from the cylinder block.

CO0A1±03
P03945
New
O±Ring
P02574
New Gasket
A02801
AB A
B
A
B
B
B
B01614
New O±Ring
CO±8
± COOLING (2JZ±GE)WATER PUMP
1546 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL WATER PUMP
(a) Install a new O±ring to the cylinder block.
(b) Install the drain hose.
(c) Install a new gasket to the water pump.
(d) Connect the water pump to the water bypass pipe. Do not
install the nut yet.
(e) Install the water pump with the 2 bolts (A) and 4 bolts (B).
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
HINT:
Hand tighten the (A) bolts first.
(f) Install the 2 nuts holding the No.2 water bypass pipe to
the water pump.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(g) Install the connector bracket (for crankshaft position sen-
sor connector) with the bolt.
(h) Install the clamp bracket (for engine wire) with the bolt.
(i) Install the generator with the bolt and nut.
Torque: 40 N´m (400 kgf´cm, 30 ft´lbf)
2. INSTALL THERMOSTAT AND WATER INLET
(See page CO±13)
3. INSTALL NO.1 WATER BYPASS PIPE AND WATER
BYPASS OUTLET
(a) Install 2 new O±rings to the No.1 water bypass pipe.
(b) Install a new O±ring and the water bypass outlet with the
2 bolts.
Torque: 9.0 N´m (90 kgf´cm, 80 in.´lbf)
4. INSTALL IDLER PULLEY AND TIMING BELT
(See page EM±23)
5. INSTALL WATER PUMP PULLEY AND DRIVE BELT
Torque: 14 N´m (140 kgf´cm, 10 ft´lbf)

EM0D6±04
A01482
A02663
5 mm Hexagon Wrench
A02649
A02690
SST
EM±16
± ENGINE MECHANICAL (2JZ±GE)TIMING BELT
1370 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE ENGINE UNDER COVER
2. DRAIN ENGINE COOLANT
3. REMOVE RADIATOR ASSEMBLY (See page CO±18)
4. REMOVE DRIVE BELT (See page CH±1)
5. REMOVE PS PUMP AND FRONT BRACKET
(a) Remove the 3 bolts, plate washer and pump front bracket.
(b) Disconnect the vane pump from the bracket.
6. REMOVE NO.3 TIMING BELT COVER
Using a 5 mm hexagon wrench, remove the 4 bolts, oil filler cap,
timing belt cover and gasket.
7. REMOVE NO.2 TIMING BELT COVER
Using a 5 mm hexagon wrench, remove the 3 bolts, timing belt
cover and gasket.
8. REMOVE DRIVE BELT TENSIONER
Remove the 3 bolts and tensioner.
NOTICE:
Be careful not to drop the bolts inside the timing belt cover.
9. LOOSEN CRANKSHAFT PULLEY BOLT
Using SST, loosen the pulley bolt.
SST 09213 ± 70010, 09330 ± 00021

A02655
Drain Hole
Rotate
(30°)
DO NOT
REMOVE
A02650
Hold
Straight
Screw
PlugSet Bolt
Seal Washer
Hexagon Wrench
A02745
SST
Bolt
± ENGINE MECHANICAL (2JZ±GE)TIMING BELT
EM±19
1373 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
18. REMOVE VVT±i (INTAKE CAMSHAFT TIMING)
PULLEY
NOTICE:

The 5 bolts shown in the illustration determine the
backlash of the gear in the timing pulley, so do not re-
move them.
If any of the 5 bolts are removed, install a new cam-
shaft timing pulley assembly.

When removing the straight screw plug, follow the
prescribed procedure in order to avoid spilling oil on
the timing system parts.
(a) Rotate the VVT±i pulley from left to right 2 to 3 times within
its range of movement (30°) and use a waste cloth to col-
lect the oil from the camshaft timing oil control valve instal-
lation hole.
NOTICE:
Approximately 20 cc (1.2 cu in.) of oil will be ejected, so
take care not to spill it.
(b) Holding the hexagon portion of camshaft with a wrench.
(c) Using a 14 mm hexagon wrench, remove the straight
screw plug and seal washer.
NOTICE:
Some oil may spill, so put a waster cloth below the plug
white doing the operation.
(d) Using a 10 mm hexagon wrench, and remove the set bolt
and VVT±i pulley.
(e) Remove the wrench.
19. REMOVE CRANKSHAFT PULLEY
Using SST and bolt (diameter: 8 mm, pitch: 1.5 mm), remove
the crankshaft pulley.
SST 09950±50012 (09951±05010, 09552±05010,
09553±05020, 09554±05030)
Bolt: Part No. 90119±18001
NOTICE:
Do not turn the crankshaft pulley.
20. REMOVE NO.1 TIMING BELT COVER
Remove the 5 bolts, timing belt cover and gasket.
21. REMOVE TIMING BELT GUIDE

EM0DA±03
A02823
A02802
B01935
Wire
Grommet
Clamp
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
EM±33
1387 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE ENGINE UNDER COVER
2. DRAIN ENGINE COOLANT
3. DISCONNECT UPPER RADIATOR HOSE FROM WA-
TER OUTLET
4. REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
5. REMOVE AIR CLEANER INLET
6. REMOVE AIR CLEANER, MAF METER AND INTAKE
AIR RESONATOR ASSEMBLY (See page EM±62)
7. REMOVE DRIVE BELT (See page CH±1)
8. DISCONNECT PS PUMP WITHOUT DISCONNECTING
HOSES
(a) Disconnect the PS air hose from the No.4 timing belt cov-
er.
(b) Disconnect the PS air hose from the air intake chamber.
(c) Remove the 2 bolts and pump rear stay.
(d) Remove the 2 bolts, and disconnect the vane pump from
the pump bracket.
HINT:
Put aside the vane pump, and suspend it.
9. DISCONNECT FRONT EXHAUST PIPE FROM EX-
HAUST MANIFOLD
(a) Disconnect the wire grommet and sensor wire of the
heated oxygen sensor (bank 2 sensor 2) from the hole
and clamp on the floor.