wheel bolts LEXUS GS400 2000 Service User Guide

SA0R6±01
F02311
R11097
F02313
SST
SA±10
± SUSPENSION AND AXLEFRONT AXLE HUB
2010 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE FRONT BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
(c) Remove the disc.
3. CHECK BEARING BACKLASH AND AXLE HUB
DEVIATION
(a) Using a dial indicator near the center of the axle hub and
check the backlash in the bearing shaft direction.
Maximum: 0.05 mm (0.0020 in.)
If the blacklash exceeds the maximum, replace the bearing.
(b) Using a dial indicator, check the deviation at the surface
of the axle hub outside the hub bolt.
Maximum: 0.05 mm (0.0020 in.)
If the deviation exceeds the maximum, replace the axle hub.
4. REMOVE ABS SPEED SENSOR
Remove the bolt and ABS speed sensor.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
5. REMOVE STEERING KNUCKLE
(a) Remove the upper side of the clip and nut.
Torque: 87 N´m (890 kgf´cm, 64 ft´lbf)
(b) Using SST, remove the steering knuckle from the upper
suspension arm.
SST 09610±20012

SA0RA±01
F02311
R05811
SST
R05812
Washer SA±16
± SUSPENSION AND AXLEFRONT WHEEL HUB BOLT
2016 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
FRONT WHEEL HUB BOLT
REPLACEMENT
1. REMOVE FRONT WHEEL
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and remove the brake caliper from the
steering knuckle.
(b) Support the brake caliper securely.
(c) Remove the disc.
3. REMOVE HUB BOLT
Using SST, remove the hub bolt.
SST 09628±10011
4. INSTALL HUB BOLT
(a) Install a washer and nut to the bolt, as shown in the il-
lustration.
(b) Turn the wheel nut to pull the hub bolt until the underside
of the hub bolt head touches the axle hub.
5. INSTALL DISC AND BRAKE CALIPER
(a) Install the disc.
(b) Install the brake caliper and 2 bolts to the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
6. INSTALL FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)

SA0RC±01
F02311
F02313
SST
F02398
SA±18
± SUSPENSION AND AXLEFRONT SHOCK ABSORBER
2018 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and caliper from the steering knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
3. DISCONNECT ABS SPEED SENSOR AND WIRE
HARNESS
(a) Remove the bolt and ABS speed sensor.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(b) Remove the bolt and ABS speed sensor wire harness.
Torque: 5.0 N´m (55 kgf´cm, 48 in.´lbf)
4. DISCONNECT UPPER SUSPENSION ARM FROM
STEERING KNUCKLE
(a) Remove the clip and nut.
Torque: 87 N´m (890 kgf´cm, 64 ft´lbf)
(b) Using SST, disconnect the upper suspension arm from
the steering knuckle.
SST 09610±20012
5. DISCONNECT STABILIZER BAR FROM STABILIZER
BAR LINK
Remove the bolt and nut, and disconnect the stabilizer bar from
the stabilizer bar link
Torque: 55 N´m (560 kgf´cm, 41 ft´lbf)

SA0RJ±01
F02316
SA±26
± SUSPENSION AND AXLEFRONT UPPER SUSPENSION ARM
2026 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE FRONT SHOCK ABSORBER
(See page SA±18)
3. REMOVE UPPER SUSPENSION ARM
Remove the 2 bolts and upper suspension arm.
Torque: 53 N´m (540 kgf´cm, 39 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the bolts.

SA0RN±01
F02311
F02312
SST
F02317
F02318
SA±30
± SUSPENSION AND AXLEFRONT LOWER SUSPENSION ARM
2030 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE ENGINE UNDER COVERS
3. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and caliper.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
(c) Remove the disc.
4. DISCONNECT TIE ROD END
(a) Remove the clip and nut.
Torque: 87 N´m (890 kgf´cm, 64 ft´lbf)
(b) Using SST, disconnect the tie rod end from the steering
knuckle.
SST 09610±20012
5. HID TYPE HEADLIGHT:
DISCONNECT HEIGHT CONTROL SENSOR LINK
FROM SHOCK ABSORBER BRACKET
Remove the nut and disconnect the height control sensor link
from the shock absorber bracket.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
6. REMOVE STABILIZER BAR LINK
(a) Remove the bolt and nut, disconnect the stabilizer bar link
from the stabilizer bar.
Torque: 55 N´m (560 kgf´cm, 43 ft´lbf)
(b) Remove the nut and stabilizer bar link.
Torque: 113 N´m (1,150 kgf´cm, 83 ft´lbf)

SA0RR±01
F02311
W00285
SST
R05802
SST SA±36
± SUSPENSION AND AXLEFRONT LOWER BALL JOINT
2036 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and caliper.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
3. DISCONNECT TIE ROD END FROM LOWER BALL
JOINT
(a) Remove the clip and nut.
Torque: 87 N´m (890 kgf´cm, 64 ft´lbf)
(b) Using SST, disconnect the tie rod end from the lower ball
joint.
SST 09610±20012
4. DISCONNECT LOWER BALL JOINT FROM LOWER
SUSPENSION ARM
(a) Remove the cotter pin and nut.
Torque: 162 N´m (1,650 kgf´cm, 119 ft´lbf)
(b) Using SST, remove the lower ball joint.
SST 09628±62011
5. REMOVE LOWER BALL JOINT FROM STEERING
KNUCKLE
Remove the 2 bolts and lower ball joint.
Torque: 113 N´m (1,150 kgf´cm, 83 ft´lbf)

SA0RZ±01
F02396
F02326
SA±44
± SUSPENSION AND AXLEREAR AXLE CARRIER
2044 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE ABS SPEED SENSOR
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
3. REMOVE REAR BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and brake caliper from the axle hub.
(b) Support the brake caliper securely.
(c) Remove the disc.
4. CHECK BEARING BACKLASH AND AXLE HUB DEVI-
ATION
(a) Using a dial indicator near the center of the axle hub and
check the backlash in the bearing shaft direction.
Maximum: 0.05 mm (0.0020 in.)
If the backlash exceeds the specified maximum, replace the
bearing.
(b) Using a dial indicator, check the deviation at the surface
of the axle hub outside the hub bolt.
Maximum: 0.07 mm (0.0028 in.)
If the deviation exceeds the specified maximum, replace the
axle hub.
5. INSTALL DISC AND BRAKE CALIPER
(a) Install the disc.
(b) Install the brake caliper and 2 bolts to the axle carrier.
Torque: 104 N´m (1,065 kgf´cm, 77 ft´lbf)
6. REMOVE DRIVE SHAFT (See page SA±52)
7. REMOVE BRAKE CALIPER AND DISC (See step 2)
8. REMOVE PARKING BRAKE SHOE
(See page BR±33)
9. DISCONNECT PARKING BRAKE CABLE
Remove the 2 bolts and disconnect the parking brake cable.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
10. DISCONNECT UPPER SUSPENSION ARM FROM
AXLE CARRIER
(a) Remove the nut.
Torque: 108 N´m (1,100 kgf´cm, 80 ft´lbf)

SA0S5±03
F02394
Matchmarks
F03449
Matchmarks
SA±52
± SUSPENSION AND AXLEREAR DRIVE SHAFT
2052 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE SUSPENSION MEMBER BRACE
Remove the 2 bolts and suspension member brace.
Torque: 50 N´m (510 kgf´cm, 37 ft´lbf)
3. REMOVE COTTER PIN, LOCK CAP AND LOCK NUT
(a) Remove the cotter pin and lock cap.
(b) With depressing the brake pedal, remove the nut.
Torque: 289 N´m (2,950 kgf´cm, 213 ft´lbf)
4. REMOVE DRIVE SHAFT
(a) Place matchmarks on the adjusting cam and lower sus-
pension arm.
(b) Remove the bolt and nut, disconnect the No.2 lower sus-
pension arm from the axle hub.
Torque: 110 N´m (1,120 kgf´cm, 81 ft´lbf)
(c) Remove the bolt and nut, disconnect the No.1 lower sus-
pension arm from the axle hub.
Torque: 75 N´m (765 kgf´cm, 55 ft´lbf)
(d) Place matchmarks on the drive shaft and side gear shaft.
NOTICE:
Do not punch to mark the matchmarks. Use paint etc.
(e) Using a 10 mm hexagon wrench, remove the 6 hexagon
bolts and 2 washers with depressing the brake pedal.
Torque: 83 N´m (850 kgf´cm, 61 ft´lbf)
HINT:
At the time of installation, apply a light coat of engine oil on the
threads of the bolts.
(f) Hold the inboard joint side of the drive shaft so that the
outboard joint side does not bend too much.

SA0SQ±01
F02383
SST
F02384
SA±94
± SUSPENSION AND AXLEREAR UPPER SUSPENSION ARM
2094 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE DRIVE SHAFT (See page SA±52)
3. REMOVE SHOCK ABSORBER (See page SA±87)
4. REMOVE UPPER SUSPENSION ARM
(a) Remove the nut.
Torque: 108 N´m (1,100 kgf´cm, 80 ft´lbf)
(b) Using SST, disconnect the upper suspension arm from
the axle carrier.
SST 09628±62011
NOTICE:

Be careful not to damage the dust cover.

Support the axle carrier.
(c) Remove the 2 bolts, nuts, washers and upper suspension
arm.
Torque: 88 N´m (900 kgf´cm, 65 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nuts.

SA0SU±01
F02385
F02386
F02387
SA±98
± SUSPENSION AND AXLEREAR LOWER SUSPENSION ARM
2098 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE REAR FENDER APRON SEAL
3. REMOVE NO.1 LOWER SUSPENSION ARM
Remove the 2 bolts, nuts, and No.1 lower suspension arm.
Torque: 75 N´m (765 kgf´cm, 55 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nuts.
4. REMOVE NO.2 LOWER SUSPENSION ARM
(a) Halogen type headlight:
Remove the bolt, nut and disconnect the stabilizer bar link
from the No.2 lower suspension arm.
Torque: 30 N´m (305 kgf´cm, 22 ft´lbf)
(b) HID type headlight:
Remove the bolt, nut and disconnect the stabilizer bar link
and the height control link from the No.2 lower suspen-
sion arm.
Torque: 30 N´m (305 kgf´cm, 22 ft´lbf)
(c) Remove the bolt, nut and disconnect the shock absorber
from the No.2 lower suspension arm.
Torque: 110 N´m (1,120 kgf´cm, 81 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nut.