brake sensor LEXUS GS400 2000 Service Owner's Manual

SA0RC±01
F02311
F02313
SST
F02398
SA±18
± SUSPENSION AND AXLEFRONT SHOCK ABSORBER
2018 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and caliper from the steering knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
3. DISCONNECT ABS SPEED SENSOR AND WIRE
HARNESS
(a) Remove the bolt and ABS speed sensor.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(b) Remove the bolt and ABS speed sensor wire harness.
Torque: 5.0 N´m (55 kgf´cm, 48 in.´lbf)
4. DISCONNECT UPPER SUSPENSION ARM FROM
STEERING KNUCKLE
(a) Remove the clip and nut.
Torque: 87 N´m (890 kgf´cm, 64 ft´lbf)
(b) Using SST, disconnect the upper suspension arm from
the steering knuckle.
SST 09610±20012
5. DISCONNECT STABILIZER BAR FROM STABILIZER
BAR LINK
Remove the bolt and nut, and disconnect the stabilizer bar from
the stabilizer bar link
Torque: 55 N´m (560 kgf´cm, 41 ft´lbf)

SA0RM±01
F02337
HID Type Headlight:
Height Control Sensor LinkPS Gear
Assembly
Pressure Feed
and Return Tubes
Shock Absorber
Bracket
No.2 Lower Suspension Arm
Strut Bar Bracket
Brake Caliper
Stabilizer Bar Link No.1 Lower Suspension
Arm
Engine Under CoverDisc Clip

Gasket
5.4 (55, 48 in.´lbf)
59 (600, 44)
118 (1,200, 87)
: Specified torque

Non±reusable partN´m (kgf´cm, ft´lbf)
87 (890, 64)
172 (1,755, 127)

Cotter Pin55 (560, 43)
164 (1,690, 122)
162 (1,650, 119)
58 (590, 43)
152 (1,550, 112)
113 (1,150, 83)
35 (360, 26)
65 (660, 48)
Engine Under Cover
Rear RH
Engine Under Cover
Rear LH
157 (1,600, 116)
± SUSPENSION AND AXLEFRONT LOWER SUSPENSION ARM
SA±29
2029 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
FRONT LOWER SUSPENSION ARM
COMPONENTS

SA0RN±01
F02311
F02312
SST
F02317
F02318
SA±30
± SUSPENSION AND AXLEFRONT LOWER SUSPENSION ARM
2030 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE ENGINE UNDER COVERS
3. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and caliper.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
(c) Remove the disc.
4. DISCONNECT TIE ROD END
(a) Remove the clip and nut.
Torque: 87 N´m (890 kgf´cm, 64 ft´lbf)
(b) Using SST, disconnect the tie rod end from the steering
knuckle.
SST 09610±20012
5. HID TYPE HEADLIGHT:
DISCONNECT HEIGHT CONTROL SENSOR LINK
FROM SHOCK ABSORBER BRACKET
Remove the nut and disconnect the height control sensor link
from the shock absorber bracket.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
6. REMOVE STABILIZER BAR LINK
(a) Remove the bolt and nut, disconnect the stabilizer bar link
from the stabilizer bar.
Torque: 55 N´m (560 kgf´cm, 43 ft´lbf)
(b) Remove the nut and stabilizer bar link.
Torque: 113 N´m (1,150 kgf´cm, 83 ft´lbf)

SA0RY±01
F03420
Washer
Suspension Member BraceBrake Caliper
Axle Carrier Assembly
Parking Brake
Cable
Parking Brake
Backing Plate Dust Deflector
Axle CarrierHub Bolt
Axle Hub
Snap Ring Disc
Lock Cap
289 (2,950, 213)
59 (600, 44)
75 (765, 55)
108 (1,100, 80)
104 (1,065, 77)Drive Shaft X6

Cotter Pin

Bearing
N´m (kgf´cm, ft´lbf): Specified torque

Non±reusable part
50 (510, 37)
83 (850, 61)
110 (1,120, 81)
7.8 (80, 69 in.´lbf)
7.8 (80, 69 in.´lbf)
59 (600, 43)
ABS Speed Sensor
± SUSPENSION AND AXLEREAR AXLE CARRIER
SA±43
2043 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REAR AXLE CARRIER
COMPONENTS

SA0RZ±01
F02396
F02326
SA±44
± SUSPENSION AND AXLEREAR AXLE CARRIER
2044 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE ABS SPEED SENSOR
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
3. REMOVE REAR BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and brake caliper from the axle hub.
(b) Support the brake caliper securely.
(c) Remove the disc.
4. CHECK BEARING BACKLASH AND AXLE HUB DEVI-
ATION
(a) Using a dial indicator near the center of the axle hub and
check the backlash in the bearing shaft direction.
Maximum: 0.05 mm (0.0020 in.)
If the backlash exceeds the specified maximum, replace the
bearing.
(b) Using a dial indicator, check the deviation at the surface
of the axle hub outside the hub bolt.
Maximum: 0.07 mm (0.0028 in.)
If the deviation exceeds the specified maximum, replace the
axle hub.
5. INSTALL DISC AND BRAKE CALIPER
(a) Install the disc.
(b) Install the brake caliper and 2 bolts to the axle carrier.
Torque: 104 N´m (1,065 kgf´cm, 77 ft´lbf)
6. REMOVE DRIVE SHAFT (See page SA±52)
7. REMOVE BRAKE CALIPER AND DISC (See step 2)
8. REMOVE PARKING BRAKE SHOE
(See page BR±33)
9. DISCONNECT PARKING BRAKE CABLE
Remove the 2 bolts and disconnect the parking brake cable.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
10. DISCONNECT UPPER SUSPENSION ARM FROM
AXLE CARRIER
(a) Remove the nut.
Torque: 108 N´m (1,100 kgf´cm, 80 ft´lbf)

SA0R5±03
F02340
Clip
Brake Caliper
ABS Speed Sensor
Hub Bolt
Disc
Steering Knuckle
Grease Cap
ABS Speed
Sensor Rotor
Snap Ring

Oil Seal
Brake Dust Cover
Axle Hub

Bearing

O±Ring
87 (890, 64)
118 (1,200, 87)
7.8 (80, 69 in.´lbf)
113 (1,150, 83)199 (2,030, 147)
8.3 (85, 74 in.´lbf)



Non±reusable part: Specified torque
N´m (kgf´cm, ft´lbf)
± SUSPENSION AND AXLEFRONT AXLE HUB
SA±9
2009 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
FRONT AXLE HUB
COMPONENTS