lock LEXUS GS400 2000 Service Owner's Manual

AT06B±01
D01050
D01051
D00999
AT±34
± AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (1UZ±FE)
1982 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE LEVEL GAUGE
2. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
3. REMOVE ENGINE UNDER COVER
4. REMOVE FRONT AND CENTER EXHAUST PIPES
(a) Disconnect he 2 heated oxygen sensor.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
HINT:
At the time of installation, please refer to the following items.

Before installing the heated oxygen sensor, twist the sen-
sor wire counterclockwise 3 and 1/2 turns.

After installing the heated oxygen sensor wire should not
twist. If it is twisted, remove the heated oxygen sensor
and reinstall it.
(b) Remove the 2 bolts and front floor center brace.
Torque: 7.4 N´m (75 kgf´cm, 65 in.´lbf)
(c) Remove the 4 bolts, nuts and 2 gaskets from the LH and
RH front TWC.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Replace the used nuts and gaskets with new ones.
(d) Remove the 2 bolts and support bracket.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
(e) Remove the 4 bolts and 2 gaskets from the tail pipe.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Replace the used gaskets with new ones.
(f) Disconnect the front and center exhaust pipes from the 2
O±rings and remove them.
5. REMOVE LH AND RH FRONT TWC
Remove the 6 nuts, 2 gaskets, LH and RH front TWC.
Torque: 62 N´m (630 kgf´cm, 46 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Replace the used nuts and gaskets with new ones.

AT5436
SST
AT06D±01
AT5437
Lock
Free
Q03546
AT4184
± AUTOMATIC TRANSMISSIONTORQUE CONVERTER CLUTCH AND DRIVE PLATE
AT±39
1987 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TORQUE CONVERTER CLUTCH
AND DRIVE PLATE
INSPECTION
1. INSPECT ONE±WAY CLUTCH
(a) Install SST so that it fits in the notch of the converter hub
and outer race of the one±way clutch.
SST 09350±30020 (09351±32020)
(b) Press on the serrations of stater with a finger and rotate
it.
Check if it rotates smoothly when turned clockwise and
locks up when turned counterclockwise.
2. MEASURE DRIVE PLATE RUNOUT AND INSPECT
RING GEAR
Set up a dial indicator and measure the drive plate runout.
Maximum runout: 0.20 mm (0.0079 in.)
If runout exceeds 0.20 mm (0.0079 in.) or if the ring gear is dam-
aged, replace the drive plate. If installing a new drive plate, note
the orientation of spacers and tighten the bolts.
Torque: 83 N´m (850 kgf´cm, 61 ft´lbf)
3. MEASURE TORQUE CONVERTER CLUTCH SLEEVE
RUNOUT
(a) Temporarily mount the torque converter clutch to the drive
plate. Set up a dial indictor.
Maximum runout: 0.30 mm (0.0118 in.)
If runout exceeds 0.30 mm (0.0118 in.), try to correct by reori-
enting the installation of the torque converter clutch.
If excessive runout cannot be corrected, replace the torque
converter clutch.
HINT:
Mark the position of the torque converter clutch to ensure cor-
rect installation.
(b) Remove the torque converter clutch.

D00911
Shift Solenoid
Valve SLN
Shift Solenoid
Valve SLTShift Solenoid
Valve S1 Shift Solenoid
Valve S3
Shift Solenoid
Valve SLU
Shift Solenoid Valve S2 Shift Solenoid Valve S4
D01741
Spring Check Ball Body
D00913
Pin
± AUTOMATIC TRANSMISSIONVALVE BODY ASSEMBLY
AT±9
1957 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
8. REMOVE SOLENOID VALVE
(a) Remove the 3 bolts and shift solenoid valve No.1, No.2
and No.3.
(b) Remove the 2 bolts, oil guide plate, lock plate, shift sole-
noid valve SLN and No.4.
(c) Remove the 6 O±rings from each shift solenoid valve.
(d) Remove the bolt, lock plate and shift solenoid valve SLU
and SLT.
9. INSTALL SOLENOID VALVE
(a) Install the shift solenoid valve SLU and SLT and the lock
plate with the bolt.
Torque: 6.4 N´m (65 kgf´cm, 56 in.´lbf)
(b) Coat 6 new O±rings with ATF.
(c) Install the 6 O±rings to the each solenoid valve.
(d) Install the shift solenoid valve SLN, No.4, lock plate and
oil guide plate with the 2 bolts.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
(e) Install the shift solenoid valve No.1, No.2 and No.3 with
the 3 bolts.
Torque:
Shift solenoid valve No.1 and No.3:
6.4 N´m (65 kgf´cm, 56 in.´lbf)
Shift solenoid valve No.2:
10 N´m (100 kgf´cm, 7 ft´lbf)
10. INSTALL CHECK BALL BODY AND SPRING
11. INSTALL VALVE BODY
(a) Align the groove of the manual valve to pin of the lever.

BE0GU±05
I01361
Ignition Switch
Buckle Switch
Driver Side Junction Block

ECU±IG Fuse
Electric Tension Reducer Solenoid
BE±104
± BODY ELECTRICALELECTRIC TENSION REDUCER SYSTEM
2405 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
ELECTRIC TENSION REDUCER SYSTEM
LOCATION

BE0GV±04
I04110
(b) (d)
Slowly
RetractedRetracted
More Quickly
I04111
Wire Harness Side
± BODY ELECTRICALELECTRIC TENSION REDUCER SYSTEM
BE±105
2406 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT TENSION REDUCER SOLENOID OPERA-
TION
(a) Connect the positive (+) lead from the battery to terminal
1, and negative (±) lead to terminal 2.
(b) Pull the belt upward and check that the belt is slowly re-
tracted when released.
(c) Disconnect the lead from the battery.
(d) Pull the belt upward and check that the belt is retracted
more quickly when released than in (b).
HINT:
Do not tilt the retractor.
If the operation is not as specified, replace the front seat outer
belt assembly.
2. INSPECT TENSION REDUCER SOLENOID CIRCUIT
Disconnect the tension reducer solenoid connector and inspect
the connector on wire harness side, as shown.
Tester connectionConditionSpecified condition
2 ± GroundBuckle switch position
OFF (belt unfastened)No continuity
2 ± GroundBuckle switch position
ON (belt fastened)Continuity
1 ± GroundIgnition switch ACC or LOCKNo voltage
1 ± GroundIgnition switch ONBattery positive voltage
If the circuit is specified, replace the front seat outer belt assem-
bly.
If the circuit is not as specified, inspect the circuits connected
to other parts.

BE0GS±10
I01362
Defogger WireIgnition SwitchDefogger Switch
Defogger Switch
Mirror Assembly

Mirror Defogger
LEXUS navigation
System
Passenger Side
Junction Block

DEF M±Fuse

MIR HTR Fuse

Mirror Defogger Relay
Mirror Assembly

Mirror Defogger
Passenger Cowl Side
Relay Block

Defogger Relay
± BODY ELECTRICALDEFOGGER SYSTEM
BE±107
2408 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
DEFOGGER SYSTEM
LOCATION

BE0GT±03
I04112
6
I04113
I04114
Wire Harness Side
Connector ºAº Connector ºBº
I01200
2 1
35
2 5
1 3
BE±108
± BODY ELECTRICALDEFOGGER SYSTEM
2409 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT DEFOGGER TIMER OPERATION
(a) Connect the positive (+) lead from the voltmeter to termi-
nal 6 of body ECU No.1 connector and negative (±) lead
to body ground.
(b) When the switch is OFF, the voltage should be approx.
12V.
(c) Turn the defogger switch ON and check that the indicator
lights up and that the voltage is less than 1 V.
(d) After 15 minutes, check that the switch is OFF and the
voltage is approx. 12 V.
If operation is not as specified, replace the switch.
2. INSPECT DEFOGGER SWITCH (in PANEL SWITCH)
CIRCUIT
Connector disconnected:
Disconnect the connector from the panel switch and inspect the
connector on wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
B10 ± GroundConstantContinuity
A1 ± GroundConstantBattery voltage
A2 ± GroundIgnition switch LOCKNo voltage
A2 ± GroundIgnition switch ACC or ONBattery voltage
If the circuit is not as specified, replace the switch.
3. INSPECT DEFOGGER RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 ± 2Continuity
Apply B+ between
terminals 1 and 2.3 ± 5Continuity
If continuity is not as specified, replace the relay.
4. INSPECT DEFOGGER RELAY CIRCUIT
(See page DI±812 and BE±21)

BE02C±02
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE±111
2412 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
POWER WINDOW CONTROL SYSTEM
TROUBLESHOOTING
1. WINDOW DOES NOT OPERATE WITH POWER WINDOW MASTER SWITCH. (MANUAL OR AU-
TOMATIC OPERATION CAN NOT BE PERFORMED.)
TroubleSuspect Area (terminal No.)Parts name
All windows do not operate with master
switch of each window.
PWS terminal of body ECU does not output sig-
nal.

Body ECU PWS terminal (B8) output

Master Switch PW terminal (15) output

Check wire harness between PWS terminal
and PW terminal (15)

Body ECU

Master switch
Windows except driver's do not operate
with master switch of each window.
Master switch (window lock circuit) faulty

Check continuity between master switch PW
terminal (15) and W/L2 terminal (10)

Check wire harness between W/L2 terminal of
master switch (10) and PCT terminals of each
power window switch.

Master switch
Only specific window does not operate.
(Manual and automatic operation can not
be performed.)
FLOW CHART ±
Only specific window does not operate.
(Automatic operation can not be per-
formed.)When ºJam Protectionº sensor is defective, auto-
matic function as a fail±safe function might be
unable.
Master switch

Power window switch

Door control ECU

Only specific window does not operate. (Neither manual nor automatic operation is available.)1
Diagnosis check:
Check output diagnosis trouble codes 21 ± 26 when operating the
master switch and power window switch.
(Refer to ºMultiplex Communication Systemº)If the door lock of the applicable seat operates.
Wire harness faulty or
D FR DOOR fuse faulty.
No Yes
Disconnect the driver door control ECU connector.
Ye sNo
Voltage check:
With ignition switch ON if 10 to 14 V power is
supplied to PCT (3) of power window switch.Wire harness faulty.
(Between master switch W/L2 terminal
(10) and power window switch PCT
terminal (3)
Continuity check:
Master switch faulty.
Check continuity master switch and power window switch.No (Driver side)
No (Except driver side)Ye s
No Ye s
Wire harness check:
Master switch
Master switch Driver door control ECU
AUTO (7)
DDN (18)
DUP (6)AUTO (B6)
MDN (B4)
MUP (B5)
Power window switch
Power window switch Driver door control ECU
A (5)
D (4)
U (6)AUTO (A22)
MDN (A23)
MUP (A24)
Wire harness faulty.
Continuity check:
Check continuity between UP terminal (A2) and
GND terminal (C12), DN terminal (A11) and
GND terminal (C12) of driver door control ECU .
Ye s
When replacing with the normal driver door control ECU
removed from another seat, if it operates normally.
Driver door control ECU faulty.No Yes
Driver door control ECU faulty.
No
Power window motor check:
Disconnect the motor connector.
Connect the battery positive (+) lead to terminal
UP (2) and negative (±) lead to terminal DN
(1) of wire harness side motor connector, check that
the motor operates.
Check power window motor.Ye s
No
Wire harness faulty.
Ye s
Power window motor faulty.
No
BE±112
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
2413 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
FLOW CHART

BE±114
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
2415 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) Only AUTO DOWN operation does not
operate.
(All window (Except driver side) doors.)
Master switch ON SC3 terminal does not output.
Driver door control ECU SC3 terminal does not
input.

Master switch SC3 terminal (13)

Driver door control ECU SC3 terminal (B11)

Check wire harness between terminal SC3 (13)
and SC3 (B11)

Driver door control ECU

Master switch
Only AUTO DOWN operation does not
operate.
(Only specific window does not operate.)Master switch faulty

Check continuity of master switch.
3. THE KEY RELATED POWER WINDOW OPERATION DOES NOT OPERATE WITH DRIVER SIDE
DOOR KEY CYLINDER. (MASTER SWITCH OPERATION IS NORMAL.)
TroubleSuspect Area (terminal No.)Parts name
Door lock system does not operate with
door key.Refer to ºPOWER DOOR LOCK CONTROL
SYSTEMº.±
Door lock system does not operate with
door key.
Fail±safe mode caused by error on jam protec-
tion sensor of power window.
(Operation of power window with multi±function
transmitter is prohibited.)
HINT: DTC 31 ± 38 output
Refer to ºMultiplex Communication Systemº.
4. POWER WINDOW DOES NOT OPERATE WITH MULTI±FUNCTION TRANSMITTER. (WINDOWS
OPERATE NORMALLY WITH MASTER SWITCH.)
TroubleSuspect Area (terminal No.)Parts name
Door lock and luggage compartment
opener do not operate with multi±function
transmitter.Refer to ºWIRELESS DOOR LOCK CONTROL
SYSTEMº.±
Only luggage compartment opener oper-
ates with multi±function transmitter.Wireless door lock transmitter faulty.Check wireless door lock transmitter.
Door lock and luggage compartment
opener operate with multi±function trans-
mitter.
Fail±safe mode caused by error on jam protec-
tion sensor of power window.
(Operation of power window with multi±function
transmitter is prohibited.)
HINT: DTC 31 ± 38 output
Refer to ºMultiplex Communication Systemº.
5. WINDOW MOVES DOWN WITHOUT BEING ORDERED DURING THE UP OPERATION
TroubleSuspect Area (terminal No.)Parts name
After the window is fully closed, it starts to
move down.
Power window motor limit switch wire harness
faulty.

Power window motor reset switch is reset.

Driver door control ECU LMT terminal (B12)

Driver door control ECU
The window moves down during the up
operation.FLOW CHART ±