heater LEXUS GS400 2000 Service Service Manual

PP0TM±01
±
PP±15
67 Author: Date:
EQUIPMENT
HeaterThermostat, ECT switch
Radiator cap tester
Rubber hose (Inside diameter 6 ± 8 mm)
Soft ± faced hammer
ThermometerThermostat, ECT switch
Torque wrench
Vernier calipers

PP0TN±01
PP±16
±
68 Author: Date:
COOLANT
ItemCapacityClassification
Engine coolant (w/ Heater)7.7 liters (8.1 US qts, 6.8 Imp. qts)Ethylene±glycol base

PP0TF±01
PP±6
± PREPARATIONENGINE MECHANICAL (2JZ±GE)
58 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
EQUIPMENT
Abrasive compoundValve
Bolt (Part No. 90105 ± 10345)For suspending engine
Bolt (Part No. 90119 ± 18001)Crankshaft pulley, Crankshaft timing pulley
Caliper gauge
CO/HC meter
Compression gauge
Connecting rod aligner
Cylinder gauge
Dial indicator
Dye penetrant
Engine tune±up tester
Heater
Micrometer
Mirror
Magnetic finger
No.1 engine hanger (Part No. 12281 ± 46050)For suspending engine
OBDII scan tool
Piston ring compressor
Piston ring expander
Plastigage
Precision straight edge
Press
Ridge reamerCylinder
Soft brash
Solvent
Spring testerValve spring
Steel squareValve spring
Thermometer
Torque wrench
Valve seat cutter
Vernier calipers
V±block
Wire brush

PP1XM±01
± PREPARATIONENGINE MECHANICAL (2JZ±GE)
PP±7
59 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
SSM (Special Service Materials)
08826±00080Seal Packing Black or equivalent
(FIPG)No.1, No.3 camshaft bearing cap
Cylinder head cover
Rear oil seal retainer
08833±00070Adhesive 1324,
THREE BOND 1324 or equivalentDrive plate bolt
Heater union
Torque converter clutch bolt
08833±00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentIdler pulley povot bolt

PP0O2±02
± PREPARATIONBODY ELECTRICAL
PP±93
145 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerEngine coolant temperature sender gauge, Engine oil level warn-
ing switch, Seat heater
SyphonBrake fluid level warning switch
Oil bathEngine oil level warning switch
Bulb (1.4 W)Defogger switch
Bulb (3.4 W)Fuel sender gauge, Engine coolant temperature receiver gauge,
Seat belt warning relay
Dry cell batteryFuel sender gauge, Power mirror
Heat lightSeat heater
Hexagon wrench (6 mm)Power seat
Torque wrench
Clip removerFor removing cowl louver
Masking tapeRear window defogger wire
Tin foilRear window defogger wire

SS0FK±01
±
SS±11
167 Author: Date:
SFI (2JZ±GE)
SERVICE DATA
Fuel pressure
regulatorFuel pressure301 ± 347 kPa (3.1 ± 3.5 kgf/cm2, 44 ± 50 psi)
Fuel pumpResistance at 20°C (68°F)0.2 ± 3.0 W
InjectorResistance at 20°C (68°F)
Injection volume
Difference between each cylinder
Fuel leakage13.4 ± 14.2 W
60 ± 73 cm3 (3.7 ± 4.5 cu in.) per 15 sec.
13 cm3 (0.8 cu in.) or less
1 drop or less per 12 minutes
MAF meterResistance (THA ± E2) at ±20°C (±4°F)
at 20°C (68°F)
at 60°C (140°F)13.6 ± 18.4kW
2.21 ± 2.69 kW
0.493 ± 0.667 kW
Throttle bodyThrottle body fully closed angle3.5°
Throttle control
motorMotor (M+ ± M±) at 20°C (68°F)
Clutch (CL+ ± CL±) at 20°C (68°F)0.3 ± 100 W
4.2 ± 5.2 W
Throttle position
sensorResistance (VC ± E2) at 20°C (68°F)
Throttle valve opening percentage STD1.2 ± 3.2 kW
15.6 ± 1.2 %
Accelerator pedal
position sensorResistance (VC ± E2) at 20°C (68°F)
Accelerator pedal position voltage STD1.2 ± 3.2 kW
0.3 ± 0.9 V
Camshaft timing
oil control valveResistance at 20°C (68°F)5.5 ± 12 W
VSV for EVAPResistance at 20°C (68°F)33 ± 39 W
VSV for acoustic
control induction
system (ACIS)Resistance at 20°C (68°F)38.5 ± 44.5 W
VSV for vapor
pressure sensorResistance at 20°C (68°F)33 ± 39 W
ECT sensorResistance at ±20°C (±4°F)
0°C (32°F)
20°C (68°F)
40°C (104°F)
60°C (140°F)
80°C (176°F)10 ± 20 kW
4 ± 7 kW
2 ± 3 kW
0.9 ± 1.3 kW
0.4 ± 0.7 kW
0.2 ± 0.4 kW
Vapor pressure
sensorPower sorce voltage4.5 ± 5.5 V
Heated oxygen
sensorHeater coil resistance at 20°C (68°F)11 ± 16 W
Fuel cut rpmFuel return rpm1,000 rpm

SF0OC±04
B08610
Ohmmeter
+B
HT
B02065
+B
HTOhmmeter
± SFI (2JZ±GE)HEATED OXYGEN SENSOR
SF±67
1533 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT HEATER RESISTANCE OF HEATED
OXYGEN SENSORS (BANK 1, 2 SENSOR 1 AND
BANK 1 SENSOR 2)
(a) Disconnect the oxygen sensor connectors.
(b) Using an ohmmeter, measure the resistance between the
terminals +B and HT.
Resistance: 11 ± 16 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 45 N´m (450 kgf´cm, 33 ft´lbf)
(c) Reconnect the oxygen sensor connectors.
2. INSPECT HEATER RESISTANCE OF HEATED
OXYGEN SENSOR (BANK 2 SENSOR 2)
(a) Take out the front side of the floor carpet.
(b) Disconnect the oxygen sensor connector.
Using an ohmmeter, measure the resistance between the
terminals +B and HT.
Resistance: 11 ± 16 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 45 N´m (450 kgf´cm, 33 ft´lbf)
(c) Reconnect the oxygen sensor connector.
(d) Reinstall the floor carpet.
3. INSPECT OPERATION OF HEATED OXYGEN SEN-
SOR (See page DI±44)

F02562
Matchmarks
A
B
F02563
SR±12± STEERINGPOWER TILT AND POWER TELESCOPIC STEERING
COLUMN
2182 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
3. REMOVE UPPER AND LOWER COLUMN COVERS
Remove the 3 screws.
4. REMOVE COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Disconnect the 4 connectors.
(b) Disconnect the airbag connector.
(c) Remove the 3 screws.
5. REMOVE SPIRAL CABLE (See page BE±34)
NOTICE:
Do not disassemble the cable or apply oil to it.
6. REMOVE NO.1 UNDER COVER
(a) Remove the 3 screws.
(b) Disconnect the OBD II.
(c) Disconnect the connectors.
7. REMOVE FINISH PLATE AND END PAD
8. REMOVE NO.1 SAFETY PAD
(a) Remove the 2 screws and disconnect the hood lock re-
lease lever from the panel.
(b) Remove 4 pad set bolts and screw.
9. REMOVE HEATER TO REGISTER DUCT NO.7
10. DISCONNECT INTERMEDIATE SHAFT ASSEMBLY
(a) Place matchmarks on the intermediate shaft and control
valve shaft.
(b) Loosen the bolt A and remove the bolt B.
11. REMOVE STEERING COLUMN ASSEMBLY
(a) Disconnect the connectors.
(b) Remove the brake pedal return spring.
(c) Loosen the hole cover clamp.
(d) Remove the 4 column assembly set nuts.
12. REMOVE INTERMEDIATE SHAFT ASSEMBLY
Remove the bolt A.
13. REMOVE DUST COVER

SR0DP±01
F02563
F02562
A
B
Matchmarks
± STEERINGPOWER TILT AND POWER TELESCOPIC STEERING
COLUMNSR±17
2187 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL DUST COVER
2. INSTALL INTERMEDIATE SHAFT ASSEMBLY
Temporarily tighten the bolt A.
3. INSTALL STEERING COLUMN ASSEMBLY
(a) Torque the 4 column assembly set nuts.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(b) Tighten the hole cover clamp.
(c) Install the brake pedal return spring.
(d) Connect the connectors.
4. CONNECT INTERMEDIATE SHAFT ASSEMBLY
(a) Align the matchmarks on the intermediate shaft and con-
trol valve shaft.
(b) Torque the bolt B.
Torque: 35 N´m (360 kgf´cm, 26 ft´lbf)
(c) Torque the bolt A.
Torque: 35 N´m (360 kgf´cm, 26 ft´lbf)
5. INSTALL HEATER TO REGISTER DUCT NO.7
6. INSTALL NO.1 SAFETY PAD
(a) Install the 4 pad set bolts and screw.
(b) Install the 2 screws and connect the hood lock release le-
ver to the panel.
7. INSTALL FINISH PLATE AND END PAD
8. INSTALL NO.1 UNDER COVER
(a) Connect the connectors.
(b) Connect the OBD II.
(c) Tighten the 3 screws.
9. INSTALL SPIRAL CABLE
(See page BE±34)
10. INSTALL COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Tighten the 3 screws.
(b) Connect the airbag connector.
(c) Connect the 4 connectors.
11. INSTALL UPPER AND LOWER COLUMN COVERS
Tighten the 3 screws.

SR0DK±03
F03671
Column Upper CoverCombination Switch
(w/ Spiral Cable)Steering Wheel Lower
No.2 CoverTorx Screw
Steering Wheel Pad
Steering Wheel
Steering Wheel Lower No.3
Cover
Finish Plate Steering Column
Assembly
Column Lower Cover
8.8 (90, 78 in.´lbf)
Torx Screw
8.8 (90, 78 in.´lbf)
35 (360, 26)
25 (260, 19)
End Pad
No.1 Safety
Pad Brake Pedal
Return Spring
Dust Cover
Intermediate Shaft
Assembly
Heater to Register Dust No.7
OBD II
No.1 Under CoverHood Lock Release
Lever
N´m (kgf´cm, ft´lbf) : Specified torque
35 (360, 26)
± STEERINGPOWER TILT AND POWER TELESCOPIC STEERING
COLUMNSR±9
2179 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
POWER TILT AND POWER TELESCOPIC STEERING
COLUMN
COMPONENTS