timing LEXUS GS400 2000 Service Service Manual

EM0DK±03
P02447
EM±76
± ENGINE MECHANICAL (2JZ±GE)CYLINDER BLOCK
1430 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
DISASSEMBLY
1. INSTALL ENGINE TO ENGINE STAND FOR
DISASSEMBLY
2. REMOVE GENERATOR
Remove the bolt, nut, pipe bracket and generator.
3. REMOVE TIMING BELT AND PULLEYS
(See page EM±16)
4. REMOVE NO.2 WATER BYPASS PIPE WITH HOSE
Remove the bolt, 2 nuts, No.2 water bypass pipe and gasket.
5. REMOVE WATER PUMP
Remove the 6 bolts, water pump and O±ring.
6. REMOVE CYLINDER HEAD (See page EM±33)
7. REMOVE OIL PRESSURE SWITCH AND KNOCK
SENSORS
Using SST, remove the switch and sensors.
SST 09816±30010
8. REMOVE OIL FILTER AND BRACKET ASSEMBLY
(a) Remove the union bolt and oil filter bracket.
(b) Remove the gasket from the union bolt.
(c) Remove the O±ring from the oil filter bracket.
9. REMOVE NO.1 OIL PIPE
Remove the union bolt, No.1 oil pipe and 2 gaskets.
10. REMOVE FUEL INLET PIPE
Remove the 2 bolts and fuel inlet pipe.
11. REMOVE LH ENGINE MOUNTING BRACKET AND
INSULATOR ASSEMBLY
Remove the 4 bolts and mounting bracket.
12. REMOVE RH ENGINE MOUNTING BRACKET AND
INSULATOR ASSEMBLY
Remove the 4 bolts and mounting bracket.
13. REMOVE OIL PUMP (See page LU±6)
14. REMOVE REAR OIL SEAL RETAINER
(a) Remove the 6 bolts of the retainer.
(b) Remove the oil seal retainer by prying the area between
the oil seal retainer and main bearing cap with a screw-
driver.

EM±96
± ENGINE MECHANICAL (2JZ±GE)CYLINDER BLOCK
1450 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
20. INSTALL OIL FILTER AND BRACKET ASSEMBLY
(a) Install a new O±ring to the oil filter bracket.
(b) Install a new gasket to the union bolt.
(c) Install the oil filter bracket with the union bolt.
Torque: 90 N´m (900 kgf´cm, 65 ft´lbf)
21. INSTALL OIL PRESSURE SWITCH AND KNOCK
SENSORS (See page LU±1, SF±63)
22. INSTALL CYLINDER HEAD (See page EM±52)
23. INSTALL WATER PUMP (See page CO±8)
24. INSTALL NO.2 WATER BYPASS PIPE WITH HOSE
(a) Install the water bypass pipe with the bolt and 2 nuts.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(b) Connect the water bypass hose to the hose clamp.
25. INSTALL TIMING PULLEYS AND BELT
(See page EM±23)
26. INSTALL GENERATOR
Install the generator and pipe bracket with the bolt and nut.
Torque: 40 N´m (400 kgf´cm, 30 ft´lbf)
27. REMOVE ENGINE STAND FROM ENGINE

V08423 Knock Sensor 1
GRECM
KNK
E1 12
E6
WIRING DIAGRAM
Wiring Diagram
This shows a wiring diagram of the circuit.
Use this diagram together with ELECTRICAL
WIRING DIAGRAM to thoroughly understand the
circuit.
Wire colors are indicated by an alphabetical code.
B = Black, L = Blue, R = Red, BR = Brown,
LG = Light Green, V = Violet, G = Green,
O = Orange, W = White, GR = Gray, P = Pink,
Y = Yellow, SB = Sky Blue
The first letter indicates the basic wire color and
the second letter indicates the color of the stripe.
DTC P0325Knock Sensor 1 Circuit Malfunction
CIRCUIT DESCRIPTION
Knock sensor is fitted to the cylinder block to detect engine knocking. This sensor contains a piezoelectric element which
generates a voltage when it becomes deformed, which occurs when the cylinder block vibrates due to knocking. If engine
knocking occurs, ignition timing is retarded to suppress it.
DTC No. DTC Detecting Condition Trouble Area
P0325No knock sensor 1 signal to ECM with engine speed,
1,200 rpm or more.
Open or short in knock sensor1 circuit

Knock sensor 1 (looseness)

ECM
If the ECM detects the above diagnosis conditions, it operates the fall safe function in which the corrective retard angle
value is set to the maximum value.

Diagnostic Trouble Code No. and Detection Item

Circuit Description
The major role and operation, etc. of the circuit
and its component parts are explained.

Indicates the diagnostic trouble code, diagnostic
trouble code set parameter and suspect area of
the problem.


± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN±29
29 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
6. CIRCUIT INSPECTION
How to read and use each page is shown below.

± INTRODUCTIONTERMS
IN±39
39 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) OEM
Original Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead Valve
OPTOption
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
PKBParking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take±Off
R & PRack And Pinion
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight±Hand
RHDRight±Hand Drive
RLYRelay
ROMRead Only Memory
RrRear
RRRear±Engine Rear±Wheel Drive
RRSRigid Rear Suspension
RWDRear±Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SOCState Of Charge
SOHCSingle Overhead Camshaft
SPECSpecification
SPISingle Point Injection
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
STJCold±Start Fuel Injection
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TBIThrottle Body Electronic Fuel Injection
TCTurbocharger
TCCSTOYOTA Computer±Controlled System
TCVTiming Control Valve
TDCTop Dead Center

Z17748
A
AB
BSeal Width
4 ± 5 mm
P02404
New Gasket
A02760
New O±Ring
Push
LU±14
± LUBRICATION (2JZ±GE)OIL PUMP
1586 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

Using a non±residue solvent, clean both sealing
surfaces.
NOTICE:
Do not use a solvent which will affect the painted surfaces.
(b) Apply seal packing to the No.2 oil pan as shown in the il-
lustration.
Seal packing: Part No.08826±00080 or equivalent

Install a nozzle that has been cut to a 4 ± 5 mm (0.16
± 0.20 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.

Parts must be assembled within 5 minutes of application.
Otherwise the material must be removed and reapplied.

Immediately remove nozzle from the tube and reinstall
cap.
(c) Install the No.2 oil pan with the 16 bolts and 2 nuts.
Torque: 9.0 N´m (90 kgf´cm, 80 in.´lbf)
6. INSTALL OIL LEVEL SENSOR
(a) Install a new gasket to the level sensor.
(b) Install the level sensor with the 4 bolts.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(c) Connect the level sensor connector.
7. INSTALL OIL DIPSTICK GUIDE AND DIPSTICK
(a) Install a new O±ring on the dipstick guide.
(b) Apply soapy water on the O±ring.
(c) Push in the dipstick guide into the guide hole of the No.1
oil pan.
(d) Install the dipstick guide with the bolt.
(e) Install the dipstick.
(f) Connect the engine wire clamp to the dipstick guide.
8. INSTALL CRANKSHAFT TIMING PULLEY, IDLER
PULLEY AND TIMING BELT (See page EM±23)

LU05I±01
B01978
No.3 Timing Belt Cover
Oil Filler Cap
Engine Wire Clamp Crankshaft Position Sensor
Oil Pump
Oil Level Sensor Connector
Oil Dipstick and Guide  O±Ring
Gasket  Crankshaft Front Oil Seal
Timing Belt Plate
No.2 Timing Belt Cover
Timing BeltOil Level Sensor
Oil Strainer Oil Pan Baffle Plate
Timing Belt Tensioner
Engine Oil Drain PlugTiming Belt Guide Drive Belt Tensioner
No.1 Timing Belt Cover
No.2 Oil Pan
Gasket
Idler Pulley

35 (350, 26)
 O±Ring
 O±Ring
21 (210, 15)
x 9
8.0 (80, 71 in.´lbf)
x 5
 Gasketx 16
 Gasket
x 6 x 16
No.1 Oil Pan
Crankshaft Pulley
330 (3,300, 243)
27 (270, 20)
Dust Boot
Crankshaft Timing
Pulley
 Gasketx 6
N´m (kgf´cm, ft´lbf) : Specified torque
 Non±reusable part

Precoated part
LU±4
± LUBRICATION (2JZ±GE)OIL PUMP
1576 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
OIL PUMP
COMPONENTS

LU05J±01
B01989
O±Ring
Pull
P10747
Z02375
SSTSST LU±6
± LUBRICATION (2JZ±GE)OIL PUMP
1578 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
HINT:
When repairing the oil pump, the oil pan and strainer should be
removed and cleaned.
1. REMOVE ENGINE WITH TRANSMISSION
(See page EM±62)
2. SEPARATE ENGINE AND TRANSMISSION
(See page EM±62)
3. INSTALL ENGINE TO ENGINE STAND FOR
REMOVAL
4. REMOVE CRANKSHAFT POSITION SENSOR
5. REMOVE TIMING BELT, IDLER PULLEY AND CRANK-
SHAFT TIMING PULLEY (See page EM±16)
6. REMOVE OIL DIPSTICK AND GUIDE
(a) Disconnect the engine wire clamp from the dipstick guide.
(b) Remove the bolt.
(c) Pull out the dipstick guide together with the dipstick.
(d) Remove the O±ring from the dipstick guide.
7. REMOVE OIL LEVEL SENSOR
(a) Disconnect the level sensor connector.
(b) Remove the 4 bolts and level sensor.
(c) Remove the gasket from the level sensor.
NOTICE:
Be careful not to drop the oil level sensor when removing
it.
8. REMOVE NO.2 OIL PAN
(a) Remove the 16 bolts and 2 nuts.
(b) Insert the blade of SST between the No.1 and No.2 oil
pan, break the seal of the applied sealer and remove the
No.2 oil pan.
SST 09032±00100
NOTICE:
Be careful not to damage the No.2 oil pan contact surface
of the No.1 oil pan. Be careful not to damage the oil pan
flange.

MA004±04
B01384
± MAINTENANCEENGINE
MA±5
48 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
ENGINE
INSPECTION
HINT:
Inspect these items when the engine is cold.
1. REPLACE TIMING BELT
(2JZ±GE ENGINE: See page EM±16)
(1UZ±FE ENGINE: See page EM±14)
2. INSPECT DRIVE BELT
(2JZ±GE ENGINE: See page CH±1)
(1UZ±FE ENGINE: See page CH±1)
3. REPLACE SPARK PLUGS
(2JZ±GE ENGINE: See page IG±1)
(1UZ±FE ENGINE: See page IG±1)
4. INSPECT AIR FILTER
(a) Remove the air filter.
(b) Visually check that the air filter is not excessively dam-
aged or oily.
If necessary, replace the air filter.
(c) Clean the filter with compressed air.
First blow from the inside thoroughly, then blow the out-
side of the filter.
(d) Reinstall the air filter.
5. REPLACE AIR FILTER
Replace the air filter with a new one.
6. REPLACE ENGINE OIL AND OIL FILTER
(2JZ±GE ENGINE: See page LU±2)
(1UZ±FE ENGINE: See page LU±3)
7. REPLACE ENGINE COOLANT
(2JZ±GE ENGINE: See page CO±2)
(1UZ±FE ENGINE: See page CO±2)
8. REPLACE GASKET IN FUEL TANK CAP
(2JZ±GE ENGINE: See page EC±7)
(1UZ±FE ENGINE: See page EC±7)
9. INSPECT FUEL LINES AND CONNECTIONS
Visually check the fuel lines for cracks, leakage, loose connec-
tions, deformation or tank band looseness.
10. INSPECT EXHAUST PIPES AND MOUNTINGS
Visually check the pipes, hangers and connections for severe
corrosion, leaks or damage.
11. ADJUST VALVE CLEARANCE
(2JZ±GE ENGINE: See page EM±5)
(1UZ±FE ENGINE: See page EM±4)

± PREPARATIONENGINE MECHANICAL (2JZ±GE)
PP±3
55 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(09316±00051)Replacer ºDºCamshaft oil seal
09330±00021Companion Flange Holding ToolCrankshaft pulley
09816±30010Oil Pressure Switch SocketKnock sensor
Oil pressure switch
09843±18020Diagnosis Check Wire
09950±50012Puller C Set
(09951±05010)Hanger 150Crankshaft pulley
Crankshaft timing pulley
(09952±05010)Slide ArmCrankshaft pulley
Crankshaft timing pulley
(09953±05020)Center Bolt 150Crankshaft pulley
Crankshaft timing pulley
(09954±05010)Claw No.1Crankshaft timing pulley
(09954±05030)Claw No.3Crankshaft pulley
09950±70010Handle Set
(09951±07100)Handle 100Valve guide bushing
Crankshaft rear oil seal
09960±10010Variable Pin Wrench Set

PP±4
± PREPARATIONENGINE MECHANICAL (2JZ±GE)
56 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(09962±01000)Variable Pin Wrench Arm AssyCamshaft timing pulley
(09963±01000)Pin 10Camshaft timing pulley