belt LEXUS GS400 2000 Service Workshop Manual

A02698
Seal Packing
A11122
A11123
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
EM±55
1409 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(b) Install the VV±i (intake camshaft timing) pulley.
(See page EM±23)
7. CONNECT TIMING BELT TO CAMSHAFT TIMING
PULLEYS (See page EM±23)
8. INSTALL NO.1 AND NO.2 CYLINDER HEAD COVERS
(a) Remove the any old packing (FIPG) material.
(b) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826±00080 or equivalent
(c) Install the gaskets to the cylinder head covers.
(d) Install the cylinder head covers with the 12 bolts and 4
nuts.
Torque: 8.5 N´m (85 kgf´cm, 75 in.´lbf)
9. INSTALL INTAKE MANIFOLD ASSEMBLY
(a) Install a new gasket and the intake manifold and delivery
pipe assembly with the 7 bolts and 2 nuts.
Torque: 28 N´m (280 kgf´cm, 21 ft´lbf)
(b) Pass the water bypass hose between the No.2, No.3 in-
take ports of the manifold and delivery pipe.
(c) Install the manifold stay with the 2 bolts.
Torque: 40 N´m (400 kgf´cm, 30 ft´lbf)
(d) Install the starter wire to the manifold stay.
10. INSTALL FUEL PRESSURE PULSATION DAMPER
(See page SF±27)
11. CONNECT ENGINE WIRE TO CYLINDER HEAD
(a) Install the engine wire protector with the 3 nuts.
(b) Using a 5 mm hexagon wrench, install the bolt holding the
engine wire protector to the No.2 cylinder head cover.
(c) Connect the 6 injector connectors.
HINT:
The Nos.1, 3, 5 injector connectors and dark gray, and the
Nos.2, 4, 6 injector connectors are brown.
(d) Connect the camshaft timing oil control valve connector.
(e) Connect the camshaft position sensor connector.
(f) Connect the ECT sensor connector.

A02733
Clamp Bracket
A02811
A02732
(v)(s)(t)
(u)(u)
(t)
(s) EM±56
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
1410 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(g) Connect the 2 knock sensor connector.
(h) Connect the starter connector.
(i) Connect the oil pressure switch connector.
(j) Connect the oil level sensor connector.
(k) Install the clamp bracket to the intake manifold.
(l) Connect the 2 wire clamps to the No.1 oil pipe and clamp
bracket on the intake manifold.
(m) Install the 2 ground terminals to the intake manifold.
Tighten so that each calking part should face inside.
(n) Install the clamp bracket to the water pump.
(o) Connect the generator connector.
(p) Connect the crankshaft position sensor connector.
(q) Connect the heated oxygen sensor (bank 1 sensor 1)
connector.
(r) Secure the engine wire with the clamp.
(s) Install the 2 hose clamps to the cylinder head and oil filter
bracket.
(t) Install the heated oxygen sensor (bank 2 sensor 1) con-
nector and engine wire clamp to the hose clamps.
(u) Install the 2 water bypass hoses to the hose clamps on
the cylinder head and oil filter bracket.
(v) Install the ground strap to the cylinder head.
12. INSTALL SPARK PLUGS
13. INSTALL IGNITION COILS AND HIGH±TENSION
CORD SET ASSEMBLY (See page IG±9)
14. INSTALL NO.3 TIMING BELT COVER
Torque: 8.0 N´m (80 kgf´cm, 71 in.´lbf)

B01935
Wire
Grommet
Clamp
A02802
EM±58
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
1412 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
Torque: 44 N´m (440 kgf´cm, 32 ft´lbf)
(d) Connect the wire grommet and sensor wire of the the
heated oxygen sensor (bank 2 sensor 2) to the hole and
clamp on the floor.
23. INSTALL PS PUMP
(a) Install the vane pump with the 2 bolts.
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
(b) Install the pump rear stay with the 2 bolts.
Torque: 39.2 N´m (400 kgf´cm, 29 ft´lbf)
(c) Connect the PS air hose to the No.4 timing belt cover.
(d) Connect the PS air hose to the air intake chamber.
24. INSTALL DRIVE BELT (See page CH±1)
25. INSTALL AIR CLEANER, MAF METER AND INTAKE
AIR RESONATOR ASSEMBLY (See page EM±68)
26. INSTALL AIR CLEANER INLET
27. CONNECT UPPER RADIATOR HOSE TO WATER OUT-
LET
28. INSTALL ENGINE COVER
Install the engine cover with the 4 nuts.
29. FILL WITH ENGINE COOLANT
30. START ENGINE AND CHECK FOR LEAKS
31. INSTALL ENGINE UNDER COVER
32. ROAD TEST
Check for abnormal noise, shock, slippage, correct shift points
and smooth operation.
33. RECHECK ENGINE COOLANT LEVEL

EM0DG±03
A09759
Air Cleaner,
MAF Meter and
Intake Air Resonator
Assembly
PCV Hose
Hood SupportHood
MAF Meter
Connector
Engine Wire
ClampWasher Hose
Accelerator Cable PS Air Hose
EVAP Hose
Air Cleaner Inlet
Radiator Lower Hose
Engine Under CoverFront Suspension
Member Brace x 6
x 18 Radiator Upper Hose
Upper Radiator
Drive Belt
ECM Outlet Duct
ECT Switch Connector
Connector
Radiator Assembly Radiator Lower Support
Oil Cooler Hose for A/TEVAP Hose
Heater
Hose
Support
Electric Cooling Fan Engine Cover
± ENGINE MECHANICAL (2JZ±GE)ENGINE UNIT
EM±59
1413 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
ENGINE UNIT
COMPONENTS

EM0DH±05
A02753
EVAP
Hose
Clamp
MAF Meter
Connector
A02751
EM±62
± ENGINE MECHANICAL (2JZ±GE)ENGINE UNIT
1416 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE HOOD
NOTICE:
Be careful not to damage the body or glass with the hood
end.
2. REMOVE ENGINE UNDER COVER
3. DRAIN ENGINE COOLANT
4. DRAIN ENGINE OIL
5. REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
6. REMOVE AIR CLEANER INLET
7. REMOVE AIR CLEANER, MAF METER AND INTAKE
AIR RESONATOR ASSEMBLY
(a) Disconnect the MAF meter connector.
(b) Disconnect the engine wire clamp from the air cleaner
case.
(c) Disconnect the EVAP hose from the air cleaner case.
(d) Disconnect the PS air hose from the No.4 timing belt cov-
er.
(e) Disconnect the PCV hose from the No.2 cylinder head
cover.
(f) Loosen the hose clamp bolt holding the intake air resona-
tor to the throttle body.
(g) Remove the 3 bolts, the air cleaner, MAF meter and intake
air resonator assembly.
8. DISCONNECT ACCELERATOR CABLE FROM EN-
GINE
9. REMOVE RADIATOR ASSEMBLY (See page CO±18)
10. REMOVE DRIVE BELT (See page CH±1)
11. REMOVE FRONT SUSPENSION MEMBER BRACE
Remove the 6 bolts and brace.

A02823
A01483
A02794
A02791
A02789
Matchmark
Wire Clamp
EM±64
± ENGINE MECHANICAL (2JZ±GE)ENGINE UNIT
1418 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
14. DISCONNECT PS PUMP AND A/C COMPRESSOR
WITHOUT DISCONNECTING HOSES
(a) Disconnect the PS air hose from the No.4 timing belt cov-
er.
(b) Disconnect the PS air hose from the air intake chamber.
(c) Remove the 2 bolts and pump rear stay.
(d) Remove the 3 bolts and plate washer, and disconnect the
vane pump assembly from the engine.
(e) Loosen the nut.
(f) Using a torx socket (E10), remove the stud bolt and nut.
(g) Disconnect the PPS solenoid valve connector.
(h) Disconnect the A/C compressor connector.
(i) Remove the 2 bolts, and disconnect the compressor from
the engine.
HINT:
Put aside the vane pump and compressor, and suspend it se-
curely.
15. REMOVE PROPELLER SHAFT (See page PR±4)
16. REMOVE TRANSMISSION CONTROL ROD
Remove the 2 nuts and control rod.
17. DISCONNECT PS GEAR HOUSING
(a) Check the steering wheel at the straight±ahead position,
and place matchmarks on the sliding yoke and intermedi-
ate shaft.
(b) Remove the bolt holding the sliding yoke to the steering
intermediate shaft.
(c) Disconnect the PS pressure switch connector and wire
clamp.

A02794
A02804A BA
A02823
A02786
A02759
Ground
Cable
± ENGINE MECHANICAL (2JZ±GE)ENGINE UNIT
EM±71
1425 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
13. INSTALL A/C COMPRESSOR AND PS PUMP
(a) Temporarily install the compressor with the 2 bolts.
(b) Using a torx socket (E10), install the stud bolt.
Torque: 26 N´m (265 kgf´cm, 19 ft´lbf)
(c) Tighten the nut and 2 bolts.
Torque: 52 N´m (530 kgf´cm, 38 ft´lbf)
(d) Connect the compressor connector.
(e) Connect the PPS solenoid valve connector.
(f) Install the vane pump assembly with the 3 bolts and plate
washer.
Torque:
57.9 N´m (590 kgf´cm, 43 ft´lbf) for A bolts
52 N´m (530 kgf´cm, 38 ft´lbf) for B bolt
(g) Install the pump rear stay with the 2 bolts.
Torque: 39.2 N´m (400 kgf´cm, 29 ft´lbf)
(h) Connect the PS air hose to the No.4 timing belt cover.
(i) Connect the PS air hose to the air intake chamber.
14. CONNECT ENGINE WIRE TO ECM BOX
(a) Install the engine wire grommet to the ECM box.
(b) Connect the 3 ECM connectors.
(c) Connect the 4 wire harness connectors.
(d) Connect the 2 junction connectors.
(e) Install the ECM cover and ECM hood.
15. CONNECT CLAMPS, WIRES, CONNECTORS, HOSES,
CABLE AND STRAP
(a) Connect the 2 engine wire clamps to the clamp brackets.
(b) Connect the DLC1.
(c) Connect the igniter connector.
(d) Connect the ground cable to the bracket on the cylinder
block.
(e) Connect the engine wire clamp to the wire clip of the gen-
erator.
(f) Connect the generator wire.

A02765
EVAP Hose
A02751
A02753
EVAP
Hose Clamp
MAF Meter
Connector
EM±72
± ENGINE MECHANICAL (2JZ±GE)ENGINE UNIT
1426 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(g) Connect the heated oxygen sensor (bank 1 sensor 1)
connector.
(h) Connect the heated oxygen sensor (bank 1 sensor 2)
connector.
(i) Connect the EVAP hose to the pipe (from charcoal canis-
ter).
(j) Connect the heater hose to the heater pipe.
(k) Connect the heater hose to the water bypass pipe.
(l) Connect the ground strap to the dash panel.
(m) Connect the fuel inlet hose to the fuel pipe support.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
(n) Connect the starter wire to the terminal and manifold stay.
(o) Connect the ground wire to the floor.
16. INSTALL FRONT SUSPENSION MEMBER BRACE
Install the brace with the 6 bolts.
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
17. INSTALL DRIVE BELT (See page CH±1)
18. INSTALL RADIATOR ASSEMBLY (See page CO±23)
19. CONNECT ACCELERATOR CABLE TO ENGINE
20. INSTALL AIR CLEANER, MAF METER AND INTAKE
AIR CONNECTOR PIPE ASSEMBLY
(a) Connect the intake air resonator to the throttle body.
(b) Install the air cleaner case with the 3 bolts.
(c) Tighten the hose clamp bolt holding the intake air resona-
tor to the throttle body.
(d) Connect the MAF meter connector.
(e) Connect the engine wire clamp to the air cleaner case.
(f) Connect the EVAP hose to the air cleaner case.
(g) Connect the PS air hose to the No.4 timing belt cover.
(h) Connect the PCV hose to the No.2 cylinder head cover.
21. INSTALL AIR CLEANER INLET
22. INSTALL ENGINE COVER
Install the engine cover with the 4 nuts.
23. FILL WITH ENGINE COOLANT
24. FILL WITH ENGINE OIL
25. START ENGINE AND CHECK FOR LEAKS
26. INSTALL ENGINE UNDER COVER

EM0DK±03
P02447
EM±76
± ENGINE MECHANICAL (2JZ±GE)CYLINDER BLOCK
1430 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
DISASSEMBLY
1. INSTALL ENGINE TO ENGINE STAND FOR
DISASSEMBLY
2. REMOVE GENERATOR
Remove the bolt, nut, pipe bracket and generator.
3. REMOVE TIMING BELT AND PULLEYS
(See page EM±16)
4. REMOVE NO.2 WATER BYPASS PIPE WITH HOSE
Remove the bolt, 2 nuts, No.2 water bypass pipe and gasket.
5. REMOVE WATER PUMP
Remove the 6 bolts, water pump and O±ring.
6. REMOVE CYLINDER HEAD (See page EM±33)
7. REMOVE OIL PRESSURE SWITCH AND KNOCK
SENSORS
Using SST, remove the switch and sensors.
SST 09816±30010
8. REMOVE OIL FILTER AND BRACKET ASSEMBLY
(a) Remove the union bolt and oil filter bracket.
(b) Remove the gasket from the union bolt.
(c) Remove the O±ring from the oil filter bracket.
9. REMOVE NO.1 OIL PIPE
Remove the union bolt, No.1 oil pipe and 2 gaskets.
10. REMOVE FUEL INLET PIPE
Remove the 2 bolts and fuel inlet pipe.
11. REMOVE LH ENGINE MOUNTING BRACKET AND
INSULATOR ASSEMBLY
Remove the 4 bolts and mounting bracket.
12. REMOVE RH ENGINE MOUNTING BRACKET AND
INSULATOR ASSEMBLY
Remove the 4 bolts and mounting bracket.
13. REMOVE OIL PUMP (See page LU±6)
14. REMOVE REAR OIL SEAL RETAINER
(a) Remove the 6 bolts of the retainer.
(b) Remove the oil seal retainer by prying the area between
the oil seal retainer and main bearing cap with a screw-
driver.

EM±96
± ENGINE MECHANICAL (2JZ±GE)CYLINDER BLOCK
1450 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
20. INSTALL OIL FILTER AND BRACKET ASSEMBLY
(a) Install a new O±ring to the oil filter bracket.
(b) Install a new gasket to the union bolt.
(c) Install the oil filter bracket with the union bolt.
Torque: 90 N´m (900 kgf´cm, 65 ft´lbf)
21. INSTALL OIL PRESSURE SWITCH AND KNOCK
SENSORS (See page LU±1, SF±63)
22. INSTALL CYLINDER HEAD (See page EM±52)
23. INSTALL WATER PUMP (See page CO±8)
24. INSTALL NO.2 WATER BYPASS PIPE WITH HOSE
(a) Install the water bypass pipe with the bolt and 2 nuts.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(b) Connect the water bypass hose to the hose clamp.
25. INSTALL TIMING PULLEYS AND BELT
(See page EM±23)
26. INSTALL GENERATOR
Install the generator and pipe bracket with the bolt and nut.
Torque: 40 N´m (400 kgf´cm, 30 ft´lbf)
27. REMOVE ENGINE STAND FROM ENGINE