hood open LEXUS GS400 2000 Service Repair Manual

BE0GQ±03
I01365
Luggage Compartment
Courtesy SwitchIgnition Switch
Door Lock Assembly

Door Lock Motor

Door Unlock Detection
Switch

Door Key Lock and
Unlock Switch
Door Lock Assembly

Door Lock Motor

Door Unlock Detection
Switch

Door Key Lock and Unlock SwitchLuggage Compartment
Opener Switch
Luggage Compartment
Key Lock and Unlock
Switch
Horn Theft Deterrent HornEngine Room No.1 Junction Block

HORN Fuse

Headlight Control Relay

Starter Relay
Engine Hood Courtesy Switch
Driver Side Junction Block

ST Fuse

Taillight Control RelayEngine Room No.2 Relay Block

Horn Relay
BE±140
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
2441 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
THEFT DETERRENT SYSTEM
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

DI3CO±10
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±141
2442 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
PRE±CHECK
1. THEFT DETERRENT SYSTEM
When the system is set to the theft deterrent mode and any of
the following conditions are met, the system sounds the horns
and flashes the headlights and the taillights for approx. 1 min-
ute.
At the same time the system locks all doors (If all door are not
locked at once, the system repeats door locking operation ev-
ery 0.55 seconds during the one minute alarm time).
There are 2 modes in this system, which are active mode and
passive mode.
All initial setting are performed in active mode. It can be
switched to passive mode by specified operation. (See step 4.
CHANGING METHOD OF PASSIVE MODE)
Condition:
Any of the doors (Including the engine hood and luggage
compartment door) is unlocked or opened without the
key. *1
The battery terminal is disconnected and reconnected.
The system receives panic signal from remote keyless
entry. *2
*1: Only active arming mode.
*2: When the ignition key is not inserted in the key cylin-
der.
There are 4 conditions in this system which are disarming
condition, disarming preparation condition, arming condition
and alarming condition.
(a) Disarming condition:
(1) When a user is near the vehicle.
(2) When the alarming function does not operate.
(3) When theft deterrent function is not performed.
(b) Disarming preparation condition:
(1) Time from a user locks a door to be leaves the ve-
hicle.
(2) Time until transferring to disarming condition.
(3) Theft deterrent function is not performed.
(c) Arming condition:
(1) When a user leaves the vehicle completely.
(2) When theft deterrent function is possible.

Disarming condition
Any of the following conditions is met

When all doors and engine hood are closed, lock all the doors using a key.

When all doors and engine hood are closed, lock all the doors using wireless remote function.

When all doors and engine hood are closed, open and close either of doors and engine hood
then close and lock all doors and engine hood.
Disarming preparation condition
Any of the following conditions is met

30 seconds elapse when the engine hood
is closed and all doors are locked.
Any of the following conditions is met

Close and open either of all doors and
engine hood.

Lock and unlock either of doors.

Insert a key into the ignition key cylinder.

Reconnect the battery.
Arming condition
Any of the following conditions is met

Unlock the locked doors using the wireless
remote function.

Unlock the locked doors using the key.

Insert the key into the ignition key cylinder
and turn the ignition key ON.
Any of the following conditions is met

Either of closed doors opens.

Either of locked doors is unlocked by any
operation other than key or wireless remote
function.

The closed engine hood is opened.

The battery is reconnected.
Alarming condition
Any of the following conditions is met

Unlock the locked doors using the wireless
remote function.

Unlock the locked doors using the key.

Insert the key into the ignition key cylinder
and turn the ignition key ON.
In this mode, once theft is detected, it is
informed using light and sound to people
around the vehicle.
The alarming time described above passes.
(Key not inserted in ignition cylinder.)
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±143
2444 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
2. ACTIVE ARMING MODE

Disarming condition (A)
Disarming preparation condition
Any of the following
conditions is met

With all doors and
engine hood closed
30 seconds elapse.
Arming condition
Any of the following conditions is met
(Refer to HINT * on the next page)

Press unlock switch of the wireless.

Insert the key into the driver and passenger
doors key cylinders, turn the key to unlock.

Insert the key into the ignition key cylinder
and turn the key to ON.
Any of the following conditions is met

Either of closed door is opened and entry
delay time elapses. (Refer to HINT on the
next page)

Engine hood is closed and opened.

Battery is reconnected.
Alarming condition
In this mode, once theft is detected, it is
informed using light and sound to people
around the vehicle.
The alarming time described above passes.
Any of the following conditions is met

Pull the key out of the ignition key cylinder which the key was inserted in.
Disarming condition (B)
Any of the following conditions is met

Press the unlock button of wireless.

Insert the key into the key cylinder of driver
or passenger seat and turn the key to unlock.

Insert the key into the ignition key cylinder.

Reconnect the battery.
Any of the following conditions is met

Open and close either of all doors and
engine hood.
Any of the following conditions is
met

Close and open either of
all doors and engine hood.Any of the following conditions is met

Press the unlock button of wireless.

Insert the key into the key cylinder of driver
or passenger seat and turn the key to unlock.

Insert the key into the ignition key cylinder.

Reconnect the battery.
Any of the following conditions is met

Press unlock switch of the wireless.

Insert the key into the driver and passenger
doors key cylinders, turn the key to unlock.

Insert the key into the ignition key cylinder
and turn the key to ON.
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±145
2446 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

Remove the ignition key from key cylinder.
All the doors, engine hood and luggage
compartment door are closed and unlocked.
Any of doors is locked and unlocked by turns
3 times by the key or remote control.
Driver's side knob for door lock is locked and
unlocked 3 times.
Driver's side door is opened.
The system starts force lock at once after 2
sec.
Driver's side knob for door lock is unlocked.
Driver's side door is closed and opened 2
times
Driver's side knob for door lock is locked and
unlocked.
The system starts force lock at once after 2
secs.
PASSIVE MODE OFF
Driver's side door is closed and opened 4
times
Driver's side knob for door lock is locked and
unlocked.
The system starts force lock at once after 2
sec.
PASSIVE MODE ON
Within
30 sec.
Within
20 sec.
HINT:

Initial mode is PASSIVE MODE OFF.

If there is a different signal in the middle of changing. It is invalid.
Input to the vehicle
Output from the vehicle BE±148
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
2449 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
6. CHANGING METHOD OF PASSIVE MODE
(ON or OFF)

± BODY ELECTRICALTROUBLESHOOTING
BE±11
2312 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) The Key related power window operations does not operate with
driver side door key cylinder.
(Master switch operation is normal.)
TROUBLESHOOTING NO.3BE±111
Power window does not operate with multi±function transmitter.
(Windows operate normally with master switch.)TROUBLESHOOTING NO.4BE±111
Window moves down without being ordered during the up opara-
tion.TROUBLESHOOTING NO.5BE±111
POWER DOOR LOCK CONTROL SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
All the doors cannot be locked or unlocked.
(Power Window Control System is normal.)1. Door Lock Control Switch
2. Wire Harness
3. Body No.1 ECUBE±131
±
DI±776
Only one side door lock control does not operate.
1. Door Lock Motor
2. Wire Harness
3. Each Door ECUBE±131
±
±
Door key related function does not operate.
1. Door Key Lock and Unlock Switch
2. Wire Harness
3. Each Door ECU
4. Body No.1 ECUBE±131
±
±
DI±776
Key confinement prevention function does not operate.
1. Key Unlock Warning Switch
2. Door Courtesy Switch
3. Wire Harness
4. Each Door ECUBE±31
BE±60
±
±
Luggage compartment door opener function does not operate.
1. Luggage Compartment Door Opener Switch
2. Luggage Compartment Door Opener Motor
3. Wire Harness
4. Body No.1 ECUBE±131
BE±131
±
DI±776
THEFT DETERRENT SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
The system cannot be set.
1. Indicator Light
2. Key Unlock Warning Switch
3. Door Unlock Detection Switch
4. Engine Hood Courtesy Switch
5. Luggage Compartment Door Courtesy Switch
6. Wire Harness
7. Each Door ECU
8. Body No.1 ECUBE±150
BE±31
BE±131
BE±150
BE±60
±
±
DI±776
The system cannot be canceled when the ignition switch is turned
to ON with key.
1. Key Unlock Warning Switch
2. Ignition Switch
3. RAD NO.2 Fuse
4. Wire Harness
5. Body No.1 ECUBE±31
BE±31
BE±21
±
DI±776
The system cannot be canceled when the luggage compartment
door is unlocked with key.1. Luggage Compartment Door Courtesy Switch
2. Wire Harness
3. Body No.1 ECUBE±60
±
DI±776
The system does not operate when the engine hood is opened.
1. Engine Hood Courtesy Switch
2. Wire Harness
3. Body No.1 ECUBE±150
±
DI±776

MA001±07
± MAINTENANCEOUTSIDE VEHICLE
MA±1
44 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
These are maintenance and inspection items which are considered to be the owner's responsibility.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item an cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge. If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing nuts. If necessary, tighten them.
4. TIRE ROTATION
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean. If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, have the cause found and corrected.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

SS0FF±03
SS±64
± SERVICE SPECIFICATIONSBODY
220 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
BODY
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
FRONT BUMPER±±±
Front bumper cover x Body5.45548 in.´lbf
Reinforcement x Body2930022
REAR BUMPER±±±
Reinforcement x Body2829021
HOOD±±±
Hood support x Hood2222516
Hood x Hood hinge2626519
Radiator support upper seal x Door lock8.08271
Hood lock nut x Hood lock8.08271
FRONT DOOR±±±
Outside handle x Door panel5.55649 in.´lbf
Door lock striker x Door panel2323517
Door hinge x Body32.533124
Door hinge x Door panel32.533124
Window regulator x Door panel1111 28
Door lock x Door panel5.55649 in.´lbf
REAR DOOR±±±
Outside handle x Door panel5.55649 in.´lbf
Door hinge x Door panel32.533124
Door hinge x Body32.533124
Window regulator x Door panel5.45548 in.´lbf
Door lock x Door panel5.45548 in.´lbf
OUTSIDE REAR VIEW MIRROR±±±
Outside rear view mirror x Door panel5.45548 in.´lbf
LUGGAGE COMPARTMENT DOOR AND HINGE±±±
Door hinge x Door panel8.08271 in.´lbf
Door lock striker x Body5.55649 in.´lbf
Door hinge x Body12.51279
FUEL LID±±±
Lock retainer x Opening lid5.55649 in.´lbf
Fuel lid lock assembly x Body Luggage side nut:5.55649 in.´lbf
Fuel lid side nut:8.08271 in.´lbf
FRONT WIPER AND WASHER±±±
Wiper arm x Wiper link2222016
Wiper link x Body5.45548 in.´lbf
SLIDING ROOF±±±
Drive rail x Bracket5.55649 in.´lbf
Sliding roof housing x Body5.55649 in.´lbf
Drive rail x Bracket8.08271 in.´lbf
Bracket x Body8.08271 in.´lbf
Sliding roof glass x Drive gear5.55649 in.´lbf

RS07Q±01
H02616
± SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
RS±53
2284 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
NOTICE:
Do not open the cover or the case of the ECU and various
computers unless absolutely necessary.
(If the IC terminals are touched, the IC may be destroyed by
static electricity.)
1. REMOVE THESE PARTS:
(See page BO±91)
(a) Finish plate
(b) End Pad
(c) No.1 under cover
(d) Hood lock release lever
(e) No.1 safety pad
(f) No.2 under cover
(g) Glove compartment finish plate
(h) Glove compartment panel assembly
(i) Front ash receptacle
(j) Cluster finish panel
(k) Console box carpet
(l) Accessary socket
(m) Accessary case
(n) Lower rear console box
(o) Rear console armrest
(p) Console box register
(q) Console box
(r) No.3 console box mounting bracket
(s) No.1 console box duct
2. REMOVE AIRBAG SENSOR ASSEMBLY
(a) Disconnect the airbag sensor connectors.
NOTICE:
Remove the connectors with the sensor assembly
installed.
(b) Using a torx wrench, remove the 3 screws and airbag sen-
sor assembly.
Torx wrench: T40 (Part No.09042±00020 or locally
manufactured tool)