ECO mode Lexus GS430 2006 Scheduled Maintenance Guide / LEXUS 2006 GS430/GS300 FROM JAN. 2005 PROD. (OM30649U) User Guide

SWITCHES
49
WINDSHIELD WIPER AND WASHERSWITCHES
Variable intermittent wipers
G12007
 1Interval adjuster 2Washer on
To turn the wipers on, move the lever down until you reach
the desired speed setting.
The engine switch must be selected in “IG −ON” mode.
There are 3 settings:
”INT” position: Intermittent operation
”LO” position: Low speed operation
”HI” position: High speed operation
Twist the interval adjuster upward to increase the wiping
time interval between sweeps, and downward to decrease
it. The wiper lever must be in the ”INT” position.
The time interval between sw
eeps is shortened when the
vehicle speed increases. When the vehicle speed reaches
more than about 20 km/h (12 mph) with the interval adjuster
twisted down to the lowest position, the time interval becomes
the shortest 1.5 seconds.
If you stop the vehicle with the wiper switch in the “LO” position,
the wiper speed automatically changes from low speed to
intermittent operation speed.* This function does not work with
the interval adjuster twisted down to the lowest position.
NOTE:
* This feature can be deactivated.
Ask your Lexus dealer for details.
For mist wiper operations (a single wipe), pull the lever up
and release it.
To make the washer squirt, push the lever toward you and
release it.
If the wiper lever is in the “OFF” position, the wipers will
automatically make 3 wipes and then a single wipe later to
sweep the windshield completely.* The interval between the
3 wipes and the last wipe will depend on the vehicle speed.
The last sweep does not happen if the vehicle speed exceeds
about 170 km/h (106 mph). NOTE:
*This function can be changed as follows: The time before the last single wipe can be set for
about 3 seconds.
 The last single wipe can be deactivated.
Ask your Lexus dealer for details.

SWITCHES
50The warning message “LOW WASHER FLUID” is displayed in
the multi−information display when the fluid level in the tank
becomes
very low. For information on adding washer fluid, see
“Adding washer fluid” on page 579.
In cold weather, warm the windshield with the defroster before
using the washer. This will help prevent icing, which could
block your vision.
NOTICE
Do not operate the wipers if the windshield is dry. It may
scratch the glass.
Rainsensing windshield wipers
G12008
 1 Automatic control adjuster 2Washer on
To turn the wipers on, move the lever down until you reach
the desired speed setting.
The engine switch must be selected in “IG −ON” mode.
There are 3 settings:
“AUTO” position: Automatic operation
“LO” position: Low speed operation
“HI” position: High speed operation

SWITCHES
55
HEADLIGHT CLEANER SWITCH
The headlight cleaner switch is located in the switch box.
G12010
Push the button to use the switch box. To spray fluid on
the headlights, push the switch with the headlights on.
The engine switch must be selected in “IG−ON” mode.
The warning message “LOW WASHER FLUID” is displayed in
the multi−information display when the fluid level in the tank
becomes very low. For information on adding washer fluid, see
“Adding washer fluid” on page 579.
After operation, be sure to close the switch box to its original
position.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, keep the switch box closed when not in
use while driving.
NOTICE
Do not turn the headlight cleaner on with the washer
fluid tank empty. It may cause the cleaner motor to
overheat.

SWITCHES
57
POWER WINDOW SWITCHES
G12012
 1For driver’s window
2For front passenger’s window
3For left rear window
4For right rear window
To raise or lower the windows, use the switch on each
door. The passengers’ windows can also be controlled by
the switches on the driver’s door.
The power windows work when the engine switch is selected
in “IG− ON” mode.
Retained accessory power operation: Even if the engine
switch is off with all the doors closed, the window can be
operated until any of the doors is opened (or for about 45
seconds).
G12023
Operating the switches
To lower the window, push the switch halfway down. Pull
it up to raise the window. The window glass moves as long
as the switch is operated.
Automatic operation: To fully raise or lower the window
automatically, pull the switch fully up or push it fully down.
To stop the window partway, lightly push or pull the switch in
the opposite direction and then release it.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
68
FUEL GAUGE
G13001
Low fuel level warning light
The gauge indicates the approximate quantity of fuel
remaining in the tank when the engine switch is selected
in “IGON” mode.
It is a good idea to keep the tank over 1/4 full.
If the fuel level approaches ”E” or the low fuel level warning light\
comes on, fill the fuel tank as soon as possible.
On inclines or curves, due to the movement of fuel in the tank,
the fuel gauge needle may fluctuate or the low fuel level
warning light may come on earlier than usual.
If the fuel tank is completely empty, the malfunction indicator
lamp comes on. Fill the fuel tank immediately.
The indicator lamp goes off after driving several times. If the
indicator lamp does not go off, contact your Lexus dealer as
soon as possible. See the inner back cover for fuel capacity and recommended
fuel selection.
ENGINE COOLANT
TEMPERATURE GAUGE
G13002
 Normal range
The gauge indicates the engine coolant temperature when
the engine switch is selected in “IGON” mode. The
engine operating temperature will vary with changes in
weather and engine load.
If the needle points to the red zone or higher, stop your vehicle
and allow the engine to cool.
Your vehicle may overheat during severe operating conditions,
such as:
 Driving up a long hill on a hot day.
 Reducing speed or stopping after high speed driving.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
70
ODOMETER AND TRIP METER
G13045
This meter displays the odometer and two trip meters. To
change the mode indication, use the “ODO TRIP” switch.
The “ODO TRIP” switch is located in the switch box.
G13004
Push the button to use the switch box and then push the
“ODO TRIP” switch. The odometer records the total distance the vehicle has
been driven. The twin trip meter records two different
distances independently.
For example, you can use one meter to calculate the fuel
economy and the other to measure the distance on each trip.
To change the trip meter indication from one trip to the
other, push the “ODO TRIP” change switch. To set the A
trip meter to
zero, display the A meter reading, then push
the “RESET” switch. The same applies for the B trip
meter.
The data of trip meters will be cancelled if the electrical power
source is disconnected.
After operation, be sure to close the switch box to its original
position.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, keep the switch box closed when not in
use while driving.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
71
LIGHT SENSITIVE OPTITRONMETER
Light sensitive optitron meter reduces unwanted glare of
the instrument cluster to provide a fine view for the driver.
The reflection of the instrument cluster is adjusted
automatically depending on the lighting condition of your
surrounding.
To make an adjustment, follow the procedure below.
The reflection control switch is located in the switch box.
G13044
Push the button to use the switch box. When you push the
“MODE” switch, the present setting appears on the
multiinformation display. To change the setting, push the “MODE” switch once and then
again within 6 seconds. Each time you push the button, the
setting changes in the following order:
1. AUTO−Norm
2. AUTO−Lo
3. AUTO−Hi
4. MANUAL−1
5. MANUAL−2
6. MANUAL−3
7. MANUAL−4
The setting display goes off automatically about 6 seconds
after the “MODE” switch is pushed. The mode shown last is
set.
After operation, be sure to close the switch box to its original
position.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, keep the switch box closed when not in
use while driving.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
74IF THIS INDICATOR OR
BUZZER COMES ON ...
DO THIS.
(p)Key reminder
buzzerTurn off the engine
switch.
(a) Brake System Warning Light (red) and Buzzer
This light comes on in the following cases when the engine
switch is selected in “IG −ON” mode.
 When the parking brake is applied ...
GS430—This light comes on fo r a few seconds when the
engine is started even after the parking brake is released.
GS300—This light comes on fo r a few seconds when the
engine switch is selected in “IG −ON” mode even after the
parking brake is released.
If you drive your vehicle without releasing the parking brake,
the buzzer sounds and the message “PARK BRAKE” appears
on the multi −information display.
 When the brake fluid level is low ...
CAUTION
It is dangerous to continue driving normally when the
brake fluid level is low.
Have your vehicle checked at your Lexus dealer in the
following case:
The light does not come on even if the parking brake is
applied when the engine is started.
 The light does not come on even if the engine is started with
the parking brake released.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
75
A warning light turning on briefly during operation does not
indicate a problem.
CAUTION
If either of the following conditions occurs, immediately
stop your
vehicle at a safe place and contact your Lexus
dealer.
 The light does not turn off even after the parking
brake is released while the engine is running.
In this case, the brakes may not work properly and
your stopping distance will become longer. Depress
the brake pedal firmly and bring the vehicle to an
immediate stop.
 The brake system warning light remains on together
with the “ABS” warning light.
In this case, not only the antilock brake system will
fail but also the vehicle will become extremely
unstable during braking.
GS430 only—Any of the following conditions may occur,
but do not indicate the malfunction:
The light may stay on for about 60 seconds after the engine
is started. It is normal if it turns off after a while.
 Depressing the brake pedal repeatedly may turn on the
warning light and buzzer. It is normal if the light turns off and
the buzzer stops sounding after a few seconds. 
You may hear a small sound in the engine compartment
after the engine is started or the brake pedal is depressed
repeatedly. This is a pump pulsating sound of the brake
system, and it is not a malfunction.
(b) Brake System Warning Light (yellow)
The light comes on when the engine switch is selected in
“IG−ON” mode.
GS430—If the engine is started, and the traction control
system, vehicle stability control system and hill −start assist
control system work properly, the light turns off after a few
seconds. Thereafter, if any part of the system malfunctions,
the light comes on again.
GS300—If the engine switch is selected in “IG −ON” mode, and
the traction control system, vehicle stability control system and
hill −start assist control system work properly, the light turns off
after a few seconds. Thereafter, if any part of the system
malfunctions, the light comes on again.
Although it is no problem to continue driving, have your vehicle
checked by your Lexus dealer as soon as possible.
(c) Driver’s Seat Belt Reminder Light and Buzzer
The light and buzzer act as a reminder to have the driver buckle
up the seat belt.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
76Once the engine switch is selected in “IG
−ON” mode, the
reminder light flashes and buzzer sounds if the driver’s seat
belt is not fastened. Unless the driver fastens the belt, the light
continues flashing and the buzzer stops after about 4 to 8
seconds.
If the vehicle speed exceeds about 15 km/h (10 mph) with the
driver’s seat belt reminder light flashing, beeps sound
intermittently for about 20 seconds.
(d) Front Passenger’s Seat Belt Reminder Light
The light acts as a reminder to have the front passenger buckle
up the seat belt.
Once the engine switch is selected in “IG −ON” mode, the
reminder light flashes if a passenger sits in the front passenger
seat and does not fasten the seat belt. Unless the front
passenger fastens the belt, the light continues flashing.
However, if a front passenger uses an additional seat cushion,
the indicator light may not flash even when the seat belt is not
buckled up.
If luggage or other load is placed on the front passenger seat,
depending on its weight and how it is placed on the seat,
built−in sensors in the seat cushion may detect the pressure,
causing the reminder light to flash.
(e) SRS Warning Light
The indicator comes on when the engine switch is
selected in “IGON” mode. It goes off after about 6
seconds. This means the SRS airbags and seat belt
pretensioners are operating properly.
This warning light system monitors the airbag sensor
assembly, front airbag sensors, side and curtain shield airbag
sensor assemblies, curtain shield airbag sensor assemblies,
driver’s seat position sensor, driver’s seat belt buckle switch,
occupant detection sensor, front passenger’s seat belt buckle
switch, seat belt pretensioner assemblies, inflators, warning
light, interconnecting wiring and power sources.
If either of the following conditions occurs, this indicates a
malfunction somewhere in the parts monitored by the warning
light system. Contact your Lexus dealer as soon as possible
to service the vehicle.
 When the engine switch is selected in “IG−ON” mode, the
light does not come on or remains on for more than 6
seconds.
 The light comes on while driving.
If the light stays on, it indicates that the SRS driver and front
passenger airba gs, SRS side and curtain shield airbags and/or
seat belt pretensioners have a problem.