start stop button Lexus GS430 2006 Scheduled Maintenance Guide / LEXUS 2006 GS430/GS300 FROM JAN. 2005 PROD. OWNER'S MANUAL (OM30649U)

KEYS AND DOORS
32OPERATING THE WINDOWS AND MOON ROOF
The windows and moon roof can be operated using an
electronic key from outside the vehicle.*
NOTE:
*The windows can be deactivated. The moon roof can be
set to slide open, tilt up or deactivated.
Ask your Lexus dealer for details.
G11017
Push the “UNLOCK” button until the windows and moon roof
start to move. When you release the button, the windows and
moon roof stop operating.
This function will work even with the window lock switch
pressed in. For vehicles sold in U.S.A.
This device complies with
Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
NOTICE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and
receiver.
 Connect the equipment into an outlet on a circuit differ-
ent from that to which the receiver is connected.

SWITCHES
45
G12002
The automatic light control sensor is on top center of the
instrument panel.
Do not place anything on the instrument panel, and/or do not
affix anything on the windshield to block this sensor.
When the headlights come on, the lights automatically turn off
about 30 seconds after any of the doors is opened and closed
with the engine switch off.* To turn them on again, select the
engine switch in “IG− ON” mode, or turn the headlight switch off
and then twist the knob until the first or second clickstop.
If you are going to park for over one week, make sure the
headlight switch is off.
When the headlight switch is on with all the doors locked and
the trunk closed, pushing the ”LOCK” button on the electronic
key turns off the headlights.
NOTE:
*The time before turning off the lights can be changed.
Ask your Lexus dealer for details. Daytime Running Light System
The headlights turn on at reduced intensity when the parking
brake is released with the engine started, even with the light
switch in the ”OFF” position. They will not
go off until the engine
switch is turned off.
To turn on the other exterior lights and instrument panel lights,
twist the knob to the first clickstop.
Twist the knob to the second clickstop to turn on the headlights
to full intensity for driving at night.
When setting the knob to the third clickstop (”AUTO”), the
headlights will automatic ally adjust to full intensity and/or turn
on the other lights depending on the darkness of the
surroundings. Likewise, as the surroundings become brighter,
the headlights will turn to reduced intensity, ultimately turning
off the other lights.
NOTICE
To prevent the battery from being discharged, do not
leave the lights on longer than necessary when the
engine is not running.

OCCUPANT RESTRAINT SYSTEMS
199
Conditions for memorized position activation

Engine switch in “IG−ON” mode and selector lever in ”P”
position, with the vehicle stopped.
 Engine switch in “OFF” mode and within 30 seconds of
opening driver’s door.
The memorized position can be activated, except for the tilt
and telescopic steering.
If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1”, “2” or \
“3”)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s
memory will be erased and the memorized positions will have
to be set again.
CAUTION
 Do not start the vehicle while the adjustments are
being made.
 Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch.
MEMORY RECALL FUNCTION
You can recall the memorized position using the entry
function or wireless remote control.
If you unlock the door using the entry function or wireless
remote control, the memorized seat position is recalled when
the driver’s door is opened. The memorized steering wheel
position will be recalled when you push the engine switch.
This function can be used after setting by the following
procedure.
Setting the driving position onto the electronic key
The driver’s door must be closed with the engine switch turned
off.
1. Push and hold the previously memorized driving position
button “1”, “2” or “3”.
2. While depressing the button above, push and hold the
“LOCK” or “UNLOCK” button on the electronic key until a beep
sounds.
If you wish to set other driv ing position, repeat the above
procedure. The previous setting will be erased and the new
position will be set.
Resetting the driving position on the electronic key
The driver’s door must be closed with the engine switch turned
off.
1. Push and hold the “SET” button.
2. Push and hold the “LOCK” or “UNLOCK” button on the
electronic key until two beeps sound.

OCCUPANT RESTRAINT SYSTEMS
201
Conditions for memorized position activation

Engine switch in “IG−ON” mode and selector lever in ”P”
position, with the vehicle stopped.
 Engine switch in “OFF” mode and within 30 seconds of
opening front passenger’s door.
If any seat position memory switch is pushed while one of the
memorized seat position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1”, “2” or \
“3”)
again.
The seat position memory control system cannot be operated
while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s
memory will be erased and the memorized positions will have
to be set again.
CAUTION
 Do not start the vehicle while the adjustments are
being made.
 Take care not to select the wrong button, or the seat
could strike the rear passenger . If this happens, you
can stop the movement by pressing another driving
position memory switch.

AUDIO
296
NOTICE
This XM tuner supports “Audio Services” (Music and
Talk) of only XM satellite radio and “Text Information”,
linked to the respective “Audio Services”.
*Text Information includes, Station Name, (Artist)
Name, (Song) Title and Category Name.
Cassette tape player operation
(a) Playing a cassette tape
G22019
When you insert a cassette tape, the exposed tape should
face to the right.
The player will automatically start when you insert a cassette
tape. At this time, the “TAPE” screen appears on the display.
If a metal or chrome equivalent cassette tape is put in the
cassette player, the player will automatically recognize it and
“MTL” appears on the display.
To stop or eject the cassette tape, push the “
” (eject)
button.

AUDIO
307
DVD player operation (For a Mark Levinson
brand audio system)
The DVD player can play audio CDs, DVD video discs and
video CDs.
For appropriate discs for this paper, see “Audio system
operating hints” on page 333.
For safety reasons, you can enjoy DVD video discs and video
CDs only when the vehicle is completely stopped with the
engine switch in “ACC” or “IG−ON” mode and the parking
brake applied. While you are driving, you can hear audio alone
even in the DVD video or video CD mode.
The DVD player can play the discs labeled as shown below. (a) Inserting or ejecting discs
The engine switch must be in “ACC” or “IG
−ON” mode.
Your automatic changer can store up to 6 discs.
G22048
 Setting a single disc:
1. Push the “LOAD” button briefly.
The green indicators at both ends of the slot start blinking and
“WAIT” appears on the display. After the blinking indicators
stay on and the “WAIT” changes to the “LOAD”, the DVD door
opens.

ELECTRICAL COMPONENTS
566
No.FUSEAMPERECIRCUIT
1 STR LOCK25Steering lock system
2 SECURITY7.5Smart access system with
push−button start
3 TI &TE20Power tilt and telescopic
steering wheel, Multiplex
communication system
4 AM17.5Starting system
5 STOP SW7.5
Stop/tail lights, Multi− port fuel
injection system/sequential
multiport fuel injection system,
Starting system, Electronic
control brake system, Vehicle
stability control system, Shift
lock system
6 OBD7.5On− board diagnosis system
7 FR P/SEAT
RH30Power seat system
8 AIR SUS20Electronic modulated
suspension
9 PWR
OUTLET15Power outlet
10 CIG15Cigarette lighter
11 ACC7.5
Multiplex communication
system, Smart access system
with push− button start, Rear
view monitor system, Audio
system, Air conditioning system
No.FUSEAMPERECIRCUIT
12 IGN10
Multi− port fuel injection
system/sequential multiport fuel
injection system, SRS airbag
system, Stop/tail lights,
Steering lock system, Electronic
control brake system
13 GAUGE7.5Gauges and meters
14 ECUIG
RH10
Power tilt and telescopic
steering wheel, Multiplex
communication system, Smart
access system with
push −button start, Audio
system, Air conditioning
system, Shift lock system, Tire
pressure warning system,
Combination switch
15 FR S/HTR
RH15Seat heater, Heated and
ventilated seats
16 RHIG7.5
Seat heater switches, Front
right door control system, Rear
right door control system,
Capacitor, Combination switch,
Seat belt pretensioners,
Intuitive parking assist
17 AM215Starting system