check oil Lexus GX470 2004 Pictorial Index / LEXUS 2004 GX470 FROM SEP. 2004 PROD. (OM60B57U) User Guide

ENGINE
561
CAUTION
Used engine oil contains potentially harmful
contaminants which may cause skin disorders such
as inflammation or skin cancer, so care should be
taken to avoid prolonged and repeated contact with
it. To remove used engine oil from your skin, wash
thoroughly with soap and water.
 Dispose of used oil and used oil filters only in a safe
and acceptable manner. Do not dispose of used oil
and used oil filters in household trash, in sewers or
onto the ground. Call your Lexus dealer or a service
station for information concerning recycling or
disposal.
 Do not leave used oil within the reach of children.
CHECKING THE ENGINE OIL LEVEL
With the engine at operating temperature and turned off,
check the oil level on the dipstick.
1. To get a correct reading, the vehicle should be on level
ground. After turning off the engine, wait a few minutes for the
oil to drain back into the bottom of the engine.
2. Pull the dipstick out, hold a rag under the end and wipe it
clean.
3. Reinsert the dipstick and push it in as far as it will go, or the
reading will not be correct.

ENGINE
563
If the oil level is below or only slightly above the low line,
add engine oil of the same type as already in the engine.
Remove the oil filler cap and add engine oil a little at a time,
checking the dipstick. We recommend that you use a funnel
when adding oil. The approximate quantity of oil needed to
raise the level between low line and full line on the dipstick is
indicated below for reference.
When the level reaches within the correct range, return the filler
cap and turn the cap clockwise until you hear a click.
Oil quantity. L (qt., lmp. qt.) 1.5 (1.6, 1.3)

ENGINE
564
NOTICE
Be careful not to spill engine oil on the vehiclecomponents.
Avoid overfilling, or the engine could be damaged.
Check the oil level on the dipstick once again afteradding the oil.

ENGINE
566To ensure excellent lubrication performance for your engine,
Toyota Genuine Motor Oilº is available, which has been
specifically tested and approved for all Lexus engines.
Please contact your Lexus dealer for further details about
Toyota Genuine Motor Oilº.
CHECKING THE ENGINE COOLANT
LEVEL

1Reservoir cap2Fº (upper) line
3Lº (lower) line
Look at the see-through coolant reservoir when the
engine is cold. The coolant level is satisfactory if it is
between the Fº and Lº lines on the reservoir. If the level
is low, add the coolant. (For the coolant type, see Coolant
type selectionº described below.)
The coolant level in the reservoir will vary with engine
temperature. However, if the level is on or below the Lº line,
add coolant. Bring the level up to the Fº line.

GAS STATION INFORMATION

Fuel selection:
Select Octane Rating 87 (Research Octane Number 91) or
higher. For improved vehicle performance, the use of
premium unleaded gasoline with an Octane Rating of 91
(Research Octane Number 96) or higher is recommended.

Fuel tank capacity:
87 L (23 gal., 19.1 lmp. gal.)

Engine oil:
Toyota Genuine Motor Oilº or equivalent
Oil grade: API grade SL Energy- Conservingº or ILSAC multigrade engine oil.
Recommended oil viscosity: SAE 5W-30
Oil capacity:
Drain and refill with filter 6.2 L (6.5 qt., 5.5 lmp. qt.)
without filter 5.7 L (6.0 qt., 5.0 lmp. qt.)
See page 561 for detailed information.

Engine coolant:
Capacity: 12.9 L (13.6 qt., 11.4 lmp. qt.)
Coolant type Ð Toyota Super Long Life Coolantº or similar
high quality ethylene glycol based non-silicate, non-amine,
non- nitrite, and non- borate coolant with long- life hybrid
organic acid technology (Coolant with long- life hybrid
organic acid technology is a combination of low phosphates and organic acids.)
Do not use plain water alone.
For checking the engine coolant, see page 566.

Automatic transmission:
Fluid type Ð Toyota Genuine ATF WSº
See page 572 for detailed information.

Tire information:
See pages 578 through 601 for detailed information.

Tire inflation pressure:
Tire size: P265/65R17 110S
Tire inflation pressure: 220kPa (2.2 kgf/cm
2 or bar, 32 psi)