maintenance Lexus HS250h 2012 Manual Online

488
4-3. Do-it-yourself maintenance
HS250h_U_75050UTurn the bulb base counterclock-
wise.
Unplug the connector while
depressing the lock release.
■ Back-up lights
Open the trunk lid and remove the
cover.
Turn the bulb base counterclock-
wise.

489
4-3. Do-it-yourself maintenance
4
Maintenance and care
HS250h_U_75050URemove the light bulb.
■ License plate lights
Open the trunk lid and remove the
cover, clips and partly remove the
cover.
Turn the bulb base counterclock-
wise.
Remove the light bulb.

490
4-3. Do-it-yourself maintenance
HS250h_U_75050U■
Rear turn signal lights
Open the trunk lid and remove the
cover.
To prevent damage to the rear
combination assembly, cover the
tip of the screwdriver with a rag.
Remove the bolts, stopper rubber
and rear combination assembly.
Turn the bulb base counterclock-
wise.
Remove the light bulb.

491
4-3. Do-it-yourself maintenance
4
Maintenance and care
HS250h_U_75050U■
Lights other than the above
If any of the lights listed below has burnt out, have it replaced by your
Lexus dealer.
● Headlight low beams (LED headlight type)
● Side turn signal lights
● Stop/tail lights
● Tail lights
● Rear side marker lights
● High mounted stoplight
● Outer foot lights
■When replacing the front righ t headlight, front turn signal lights and parking light
bulbs
■LED light bulbs
The headlight low beams (LED headlights type), side turn signal lights, rear side
marker lights, stop/tail lights, tail lights and high mounted stoplight consist of a num-
ber of LEDs. If any of the LEDs burn out, take your vehicle to your Lexus dealer to
have the light replaced. Remove the securing clip and move the
washer fluid filler opening to allow easy
access to the light bulbs.
After replacing the bulbs, make sure to
secure the washer fluid filler opening with the
clip.

492
4-3. Do-it-yourself maintenance
HS250h_U_75050U
■Condensation build-up on the inside of the lens
Contact your Lexus dealer for more information in the following situations. Tempo-
rary condensation build-up on the inside of the headlight lens does not indicate a
malfunction.
●Large drops of water have built up on the inside of the lens.
●Water has built up inside the headlight.
■When replacing light bulbs
→P. 4 8 0
CAUTION
■Replacing light bulbs
●Turn off the lights. Do not attempt to replace the bulb immediately after turning
off the lights.
The bulbs become very hot and may cause burns.
●Do not touch the glass portion of the light bulb with bare hands. Hold the bulb by
the plastic or metal portion.
If the bulb is scratched or dropped, it may blow out or crack.
●Fully install light bulbs and any parts used to secure them. Failure to do so may
result in heat damage, fire, or water entering the headlight unit. This may damage
the headlights or cause condensation to build up on the lens.
■To prevent damage or fire
Make sure bulbs are fully seated and locked.

510
5-2. Steps to take in an emergency
HS250h_U_75050U
CAUTION
■Maintenance of the tires
Each tire, including the spare (if provided), should be checked monthly when cold
and inflated to the inflation pressure recommended by the vehicle manufacturer on
the vehicle placard or tire inflation pressure label (tire and load information label).
(If your vehicle has tires of a different size than the size indicated on the vehicle
placard or tire inflation pressure label [tire and load information label], you should
determine the proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has been equipped with a tire pressure
monitoring system (TPMS-tire pressure warning system) that illuminates a low tire
pressure telltale (tire pressure warning light) when one or more of your tires is sig-
nificantly under-inflated. Accordingly, when the low tire pressure telltale (tire pres-
sure warning light) illuminates, you should stop and check your tires as soon as
possible, and inflate them to the proper pressure. Driving on a significantly under-
inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation
also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling
and stopping ability.
Please note that the TPMS (tire pressure warning system) is not a substitute for
proper tire maintenance, and it is the driver’s responsibility to maintain correct tire
pressure, even if under-inflation has not reached the level to trigger illumination of
the TPMS low tire pressure telltale (tire pressure warning light).
Your vehicle has also been equipped with a TPMS (tire pressure warning system)
malfunction indicator to indicate when the system is not operating properly. The
TPMS (tire pressure warning system) malfunction indicator is combined with the
low tire pressure telltale (tire pressure warning light). When the system detects a
malfunction, the telltale will flash for approximately one minute and then remain
continuously illuminated. This sequence will continue upon subsequent vehicle
start-ups as long as the malfunction exists. When the malfunction indicator is illumi-
nated, the system may not be able to detect or signal low tire pressure as intended.
TPMS (tire pressure warning system) malfunctions may occur for a variety of rea-
sons, including the installation of replacement or alternate tires or wheels on the
vehicle that prevent the TPMS (tire pressure warning system) from functioning
properly. Always check the TPMS (tire pressure warning system) malfunction tell-
tale after replacing one or more tires or wheels on your vehicle to ensure that the
replacement or alternate tires and wheels allow the TPMS (tire pressure warning
system) to continue to function properly.

5
When trouble arises
517
5-2. Steps to take in an emergency
HS250h_U_75050U
(Flashes)
(If equipped)
Indicates that the moon
roof is not fully closed A buzzer also sounds.
(With the “POWER”
switch off, and the
driver's door open)
Close the moon roof.
Indicates that the parking
brake is still engagedIf the vehicle reaches a
speed of 3 mph
(5 km/h),
flashes and a buzzer
sounds to indicate that
the parking brake is still
engaged.
Release the parking
brake.
Indicates that the washer
fluid level is lowAdd washer fluid.
(U.S.A. only)
Indicates that all mainte-
nance according to the
driven distance on the
maintenance schedule*
1
should be performed
soon.
If necessary, perform
maintenance.
Comes on approximately
4500 miles (7200 km)
after the maintenance
data has been reset.
Wa r n i n g m e s s a g eDetailsCorrection procedure

518
5-2. Steps to take in an emergency
HS250h_U_75050U
(U.S.A. only)
Indicates that all mainte-
nance is required to cor-
respond to the driven
distance on the mainte-
nance schedule*
1 .Pe r f o r m t h e n e c e s s a r y
maintenance.
Please reset the mainte-
nance data after the main-
tenance is performed
(→ P. 4 2 4 )
Comes on approximately
5000 miles (8000 km)
after the maintenance
data has been reset.
(The indicator will not
work properly unless the
maintenance data has
been reset.)
Indicates that the tire
inflation pressure is lowCheck the tire inflation
pressure, and adjust to the
appropriate level.
(If equipped)
Indicates that the pre-
collision system is not
currently functional
• The grille or the sensor is
dirty.
• The pre-collision system is not functional due to
overheating.
• Check the grille and the sensor and clean them if
they are dirty.
• Check that the system will become functional
after the system cools
down.
Wa r n i n g m e s s a g eDetailsCorrection procedure

5
When trouble arises
523
5-2. Steps to take in an emergency
HS250h_U_75050U*
1: Refer to the separate “Scheduled maintenance” or “Owner’s Manual
Supplement” for the maintenance interval applicable to your vehicle.
*
2: For the EV drive mode operating conditions ( →P. 1 5 7 ) .
Indicates that the EV
drive mode is not avail-
able*
2
A buzzer also sounds.
The reason the EV drive
mode is not available
(the vehicle is idling, bat-
tery charge is low, speed
is higher than the EV
drive mode operating
speed range, accelera-
tor pedal is depressed
too much) may be dis-
played.
Use the EV drive mode
when it becomes avail-
able.
(Flashes 3
times)
Indicates that the EV
drive mode has been
automatically can-
celled*
2
A buzzer also sounds.
The reason the EV drive
mode is not available
(the battery charge is
low, speed is higher than
the EV drive mode
speed range, accelera-
tor pedal is depressed
too much) may be dis-
played.
Drive the vehicle for a
while.
Wa r n i n g m e s s a g eDetailsCorrection procedure

Vehicle specifications6
559
HS250h_U_75050U
6-1. SpecificationsMaintenance data (fuel, oil level, etc.) .............. 560
Fuel information ..................... 569
Tire information...................... 572
6-2. Customization Customizable features ........ 584
6-3. Initialization Items to initialize .................... 596