air Lexus IS220d 2011 Owner's Manual

5
515
5-2. Steps to take in an emergency
When trouble arises
IS250/220d/200d_EE
If the engine will not start
If the engine will not start even though correct starting procedures are
being followed (P. 156), consider each of the following points.
The engine will not start even when the starter motor operates
normally.
One of the following may be the cause of the problem.
There may not be sufficient fuel in the vehicle’s tank.
IS250: Refuel the vehicle.
IS220d and IS200d: P. 531
The engine may be flooded. (IS250)
Try to restart the engine once more following correct start-
ing procedures. (P. 156)
There may be a malfunction in the engine immobilizer sys-
tem.
(P. 96)
The starter motor turns over slowly, the interior lights and
headlights are dim, or the horn does not sound or sounds at a
low volume.
One of the following may be the cause of the problem.
The battery may be discharged. (P. 524)
The battery terminal connections may be loose or corroded.
The starter motor does not turn over, the interior lights and
headlights do not turn on, or the horn does not sound.
One of the following may be the cause of the problem.
One or both of the battery terminals may be disconnected.
The battery may be discharged. (P. 524)
There may be a malfunction in the steering lock system.
Contact any authorized Lexus dealer or repairer, or another
duly qualified and equipped professional, if the problem can-

516
5-2. Steps to take in an emergency
IS250/220d/200d_EE
Emergency start function
When the engine does not start, the following steps can be used as
an interim measure to start the engine if the “ENGINE START
STOP” switch is functioning normally:
Vehicles with an automatic transmission
Set the parking brake.
Put the shift lever in P.
Set the “ENGINE START STOP” switch to ACCESSORY
mode.
Press and hold the “ENGINE START STOP” switch for
about 15 seconds while depressing the brake pedal firmly.
Vehicles with a manual transmission
Set the parking brake.
Put the shift lever in N.
Set the “ENGINE START STOP” switch to the ACCES-
SORY mode.
Push and hold the “ENGINE START STOP” switch for
about 15 seconds while depressing the brake pedal and
clutch pedal firmly.
Even if the engine can be started using the above steps, the system
may be malfunctioning. Have the vehicle checked by any autho-
rized Lexus dealer or repairer, or another duly qualified and
equipped professional.
STEP1
STEP2
STEP3
STEP4
STEP1
STEP2
STEP3
STEP4

5
517
5-2. Steps to take in an emergency
When trouble arises
IS250/220d/200d_EE
If the shift lever cannot be shifted from P
: If equipped
If the shift lever cannot be shifted with your foot on the brake, there
may be a problem with the shift lock system (a system to prevent acci-
dental operation of the shift lever). Have the vehicle inspected by any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional, immediately.
The following steps may be used as an emergency measure to ensure
that the shift lever can be shifted.
Set the parking brake.
Start the engine.
Depress the brake pedal.
Press the shift lock override
button.
The shift lever can be shifted
while the button is pressed.
STEP1
STEP2
STEP3
STEP4

518
5-2. Steps to take in an emergency
IS250/220d/200d_EE
If you lose your keys
New genuine Lexus keys can be made by any authorized Lexus dealer
or repairer, and another duly qualified and equipped professional,
using the other key or the key number stamped on your key number

522
5-2. Steps to take in an emergency
IS250/220d/200d_EEManual transmission
Shift the shift lever to N and depress the clutch pedal.
Touch the Lexus emblem side
of the electronic key to the
“ENGINE START STOP”
switch.
An alarm will sound to indicate
that the start function cannot
detect the electronic key that is
touched to the “ENGINE
START STOP” switch if any of
the doors is opened and closed
while the key is touched to the
switch.
To change “ENGINE START STOP” switch modes: Within
10 seconds of the buzzer sounding, release the clutch pedal
and press the “ENGINE START STOP” switch. Modes can
be changed each time the switch is pressed. (P. 158)
To start the engine: Press the “ENGINE START STOP”
switch within 10 seconds after the buzzer sounds, keeping
the clutch pedal depressed.
In the event that the engine still cannot be started, contact any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
STEP1
STEP2
STEP3

524
5-2. Steps to take in an emergency
IS250/220d/200d_EE
If the vehicle battery is discharged
The following procedures may be used to start the engine if the vehi-
cle's battery is discharged.
You can call any authorized Lexus dealer or repairer, or another duly
qualified and equipped professional.
If you have a set of jumper (or booster) cables and a second
vehicle with a 12-volt battery, you can jump start your Lexus
following the steps below.
Remove the engine compartment covers. (P. 407)
Connecting the jumper cables
Left-hand vehicles
STEP1
STEP2

5
525
5-2. Steps to take in an emergency
When trouble arises
IS250/220d/200d_EE
Right-hand vehicles
Positive (+) battery terminal on your vehicle
Positive (+) battery terminal on the second vehicle
Negative (-) battery terminal on the second vehicle
Connect the jumper cable to ground on your vehicle as shown
in the illustration.
Start the engine of the second vehicle. Increase the
engine speed slightly and maintain at that level for
approximately 5 minutes to recharge the battery of your
vehicle.
Open and close any of the doors with the “ENGINE
START STOP” switch OFF.
Maintain the engine speed of the second vehicle and turn
the “ENGINE START STOP” switch to IGNITION ON
mode, then start the vehicle's engine.
Once the vehicle’s engine has started, remove the jumper
cables in the exact reverse order in which they were con-
nected.
Once the engine starts, have the vehicle checked at any autho-
rized Lexus dealer or repairer, or another duly qualified and
STEP3
STEP4
STEP5
STEP6

528
5-2. Steps to take in an emergency
IS250/220d/200d_EE
If your vehicle overheats
If your engine overheats:
Stop the vehicle in a safe place and turn off the automatic
air conditioning system.
Check to see if steam is coming out from under the hood.
If you see steam:
Stop the engine. Carefully lift the hood after the steam
subsides and then restart the engine.
If you do not see steam:
Leave the engine running and carefully lift the hood.
Check to see if the cooling fans are operating.
If the fans are operating:
Wait until the temperature of the engine (shown on the
instrument cluster) begins to fall and then stop the
engine.
If the fans are not operating:
Stop the engine and call any authorized Lexus dealer
or repairer, or another duly qualified and equipped pro-
fessional.
After the engine has cooled
down sufficiently, check the
engine coolant level and
inspect the radiator core
(radiator) for any leaks.
If the engine compartment
cover needs to be removed:
STEP1
STEP2
STEP3
STEP4

5
529
5-2. Steps to take in an emergency
When trouble arises
IS250/220d/200d_EE
Overheating
If you observe the following, your vehicle may be overheating.
The engine coolant temperature gauge enters the red zone or a loss of
power is experienced.
Steam is coming from under the hood.
CAUTION
To prevent an accident or injury when inspecting under the hood of your
vehicle
If steam is seen coming from under the hood, do not open the hood until
the steam has subsided. The engine compartment may be very hot, caus-
ing serious injury such as burns.
Keep hands and clothing away from the fans and other belts while the
engine is running.
Do not loosen the radiator cap (IS250), or the coolant reservoir cap
(IS220d and IS200d) while the engine and radiator are hot.
Serious injury, such as burns, may result from hot coolant and steam
released under pressure.
Add engine coolant if neces-
sary.
Water can be used in an
emergency if engine coolant
is unavailable.
(P. 5 4 4)
Have the vehicle checked at the nearest authorized Lexus dealer
or repairer, or another duly qualified and equipped professional,
as soon as possible.
STEP5

5
531
5-2. Steps to take in an emergency
When trouble arises
IS250/220d/200d_EE
If you run out of fuel and the engine stalls (IS220d and IS200d)
NOTICE
When restarting the engine
Do not crank the engine before refueling and priming the fuel system. This
may damage the engine and fuel system.
If you run out of fuel and the engine dies:
Refuel your vehicle.
Prime the fuel system by
using the satellite switches.
Push “” or “” to select prim-
ing operation mode. ( )
Press the “ON/OFF” button to
select “ON”. ( )
The priming operation will
start.
Wait for 1 minute and start the engine. (P. 156)
The priming operation will automatically stop when the engine
starts.
If the engine does not start after the above steps performed,
wait for 10 seconds and try step 2 and step 3 again. If the
engine still does not start, contact any authorized Lexus dealer
or repairer, or another duly qualified and equipped profes-
sional.
fihidhl dllihl
STEP1
STEP2
STEP3