lock Lexus IS250 2014 2014-2015 IS250/350 TVIP V4 Remote Engine Starter (RES) Owners G / LEXUS 2014 IS250,IS350 (OM53758U) Service Manual

1213-3. Adjusting the seats
3
Operation of each component
IS350/250_U (OM53758U)
Check that the luggage security sys-
tem lever in the trunk is in the unlock
position.
Pull the seatback lock release lever
and fold the seatback down.
To return the rear seatbacks to their
original position, lift them up until they
lock.
P. 1 1 0
Rear seats (folding type)

: If equipped
The rear seatbacks can be folded down.
Folding down the rear seatbacks
1
2
Luggage security system

1223-3. Adjusting the seats
IS350/250_U (OM53758U)
CAUTION
Observe the following precautions. Failure to do so may result in death or serious injury.
■When folding the rear seatbacks down
●Do not fold the seatbacks down while driving.
●Stop the vehicle on level ground, set the parking brake and shift the shift lever to P.
●Do not allow anyone to sit on a folded seatback or in the trunk while driving.
●Do not allow children to enter the trunk.
■After returning the rear seatback to the upright position
●Check that the seat belts are not twisted or caught in the seatback.
●Make sure that the seatback is securely
locked in position by lightly pushing it back
and forth.
If the seatback is not securely locked, the red
marking will be visible on the seatback lock
release knob. Make sure that the red marking
is not visible.

1233-3. Adjusting the seats
3
Operation of each component
IS350/250_U (OM53758U)
Check that the shift lever is in P.
Turn the engine switch to IGNITION ON mode.
Adjust the driver’s seat, steering wheel, and outside rear view mirrors to the
desired positions.
While pressing the “SET” button, or
within 3 seconds after the “SET” but-
ton is pressed, press button “1”, “2”
or “3” until a buzzer sounds.
If the selected button has already been
preset, the previously recorded position
will be overwritten.
Check that the shift lever is in P.
Turn the engine switch to IGNITION ON mode.
Press button “1”, “2” or “3” to recall
the desired position.
Driving position memory
: If equipped
Your preferred driving position (the position of the driver’s seat, steering
wheel and outside rear view mirrors) can be memorized and recalled by
pressing a button. It is also possible to set this function to activate automati-
cally when the doors are unlocked.
Three different driving positions can be entered into memory.
Entering a position to memory
1
2
3
4
Recalling the memorized position
1
2
3

1253-3. Adjusting the seats
3
Operation of each component
IS350/250_U (OM53758U)
A desired driving position can be recalled linked with the unlocking of the door.
■Setting procedure
Record your driving position to button “1”, “2” or “3” before performing the
following:
Carrying only the key (including the card key) to which you want to link the
driving position, shift the shift lever to P and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be linked prop-
erly.
Turn the engine switch to IGNITION ON mode and recall the position
which you want to link.
While pressing the button to
recall the position, press the
driver’s door lock switch (either
lock or unlock) until the buzzer
sounds.
The driving position is recalled when
the driver’s door is unlocked using
the entry function or wireless remote
control and the driver’s door is
opened.
■Cancelation procedure
Carry only the key for which you want to cancel the linked door unlock opera-
tion.
If 2 or more keys are in the vehicle, the driving position cannot be canceled
properly.
Turn the engine switch to IGNITION ON mode.
While pressing the “SET” button, press the driver’s door lock switch (either
lock or unlock) until the buzzer sounds.
Linking driving position memory with door unlock operation
1
2
1
2

1263-3. Adjusting the seats
IS350/250_U (OM53758U)
■When driving position memory is linked with door unlock operation
If the driver’s door is opened, the driver’s seat will move toward the memorized position
but stop slightly beforehand to allow easy access to the vehicle.
Turning the engine switch to ACCESSORY or IGNITION ON mode, or fastening the
driver’s seat belt moves the seat fully into the memorized position.
■Operating the driving position memory after turning the engine switch off
Memorized seat positions can be activated up to 180 seconds after the driver’s door is
opened and another 60 seconds after it is closed again. Memorized steering wheel posi-
tion can be activated by pr essing the engine switch.
■Correct seat position
When the seat is in the most forward or mo st backward position, and the seat is being
moved in those directions, the system may not correctly recognize the current position
and the memorized position will not be correctly recalled.
■The auto away function for exiting
If the seat is already close to the rearmost position, the auto away function may not oper-
ate when the driver exits the vehicle.
■When the driving position is recalled by a memory linked door unlock operation
●Since each memorized driving position is regi stered to a specific electronic key, the
driving position recalled may be different depending on the carried key.
●When only doors other than the driver’s d oor are unlocked by the smart access system
with push-button start, the driving position will not be recalled. In this case, press a driv-
ing position memory button to recall the desired driving position.
■Customization
The distance that the driver’s seat moves b ackward during the auto away function can be
changed. (Customizable features: P. 5 2 5 )
CAUTION
■Seat adjustment caution
Take care during seat adjustment so that th e seat does not strike the rear passenger or
squeeze your body against the steering wheel.

1273-3. Adjusting the seats
3
Operation of each component
IS350/250_U (OM53758U)
◆Vertical adjustmentUp
Pull the head restraints up.
Down
Push the head restraint down while
pressing the lock release button.
◆Horizontal adjustment (if equipped)
The position of the head restraint
can be adjusted forward in 4 stages.
If the head restraint is pulled forward
from the foremost position, it will return
to the rearmost position.
Head restraints
Head restraints are provided for all seats.
Front seats
Lock release button
1
2

1283-3. Adjusting the seats
IS350/250_U (OM53758U)
Up
Pull the head restraints up.
Down
Push the head restraint down while
pressing the lock release button.
■Removing the head restraints
■Installing the head restraints
Front seats
Rear seats
Rear seats
Lock release button
1
2
Pull the head restraint up while pressing the lock
release button.
If the head restraint to uches the ceiling, making
the removal difficult, change the seat height or
angle.
Align the head restrain t with the installation
holes and push it down to the lock position.
Press and hold the lock release button when
lowering the head restraint.
Align the head restrain t with the installation
holes and push it down to the lowest lock posi-
tion while pressing the lock release button.
Lock release button
Lock release button
Lock release button

1293-3. Adjusting the seats
3
Operation of each component
IS350/250_U (OM53758U)
■Adjusting the height of the head restraints
■Adjusting the rear seat head restraint
Always raise the head restraint one level from the stowed position when using. Make sure that the head restraints are adjusted
so that the center of the head restraint is closest
to the top of your ears.
CAUTION
■Head restraint precautions
Observe the following precautions regarding the head restraints. Failure to do so may
result in death or serious injury.
●Use the head restraints designed for each respective seat.
●Adjust the head restraints to the correct position at all times.
●After adjusting the head restraints, push down on them and make sure they are
locked in position.
●Do not drive with the head restraints removed.

1313-4. Adjusting the steering wheel and mirrors
3
Operation of each component
IS350/250_U (OM53758U)
To sound the horn, press on or close to
the mark.
■The steering wheel can be adjusted when (power type)
The engine switch is in ACCESSORY or IGNITION ON mode
*.
*: If the driver’s seat belt is fastened, the steering wheel can be adjusted regardless of
engine switch mode.
■Automatic adjustment of the steering position (if equipped)
A desired steering position can be entered to memory and recalled automatically by the
driving position memory system. ( P. 1 2 3 )
■Power easy access system (if equipped)
The steering wheel and driver’s seat move in accordance with engine switch mode and
the driver’s seat belt condition. ( P. 1 2 4 )
Horn
CAUTION
■Caution while driving
Do not adjust the steering wheel while driving.
Doing so may cause the driver to mishandle the vehicle and cause an accident, result-
ing in death or serious injury.
■After adjusting the steering wheel (manual type)
Make sure that the steering wheel is securely locked.
Otherwise, the steering wheel may move suddenly, possibly causing an accident, and
resulting in death or serious injury. Also, the horn may not sound if the steering wheel is
not securely locked.

137
3
Operation of each component
IS350/250_U (OM53758U)3-5. Opening, closing the windows and moon roof
The power windows can be opened and closed using the switches.
Operating the switch moves the windows as follows:
Closing
One-touch closing
*
Opening
One-touch opening
*
*
: To stop the window partway, operate the switch in the opposite direction.
Press the switch to lock the passenger
window switches.
The indicator will come on.
Use this switch to prevent children from
accidentally opening or closing a pas-
senger window.
Power windows
Opening and closing procedures
1
2
3
4
Window lock switch
Indicator